2016 AUDI A8 change wheel

Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.,. After you experience a tire failure, pull the car
well away from moving traffic and try to reach
level ground before you stop¢.,&. .
.. All passengers should
leave the car and move
to a safe location (for instance, beh ind the
guardrail) ¢.,&. .
.,. Engage the
parking brake to prevent your vehi­
cle from rolling unintentionally ¢.,&. .
.. Move
selector lever to position P ¢ .,&. .
1> lfyou are towing a trailer, unhitch the trailer
from your vehicle.
.,. Take the
jack and the spare tire out of the lug­
gage compartment,
¢page 257.
..&, WARNING
You or your passengers could be injured wh ile
changing a wheel if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance
off the road. Turn off the engine, turn the
emergency flashers on and use other warn­
ing devices to alert other motorists.
- Make sure that passengers wa it in a safe
place away from the vehicle and well away
from the road and traffic.
- T o help prevent the vehicle from moving
sudden ly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be­
ing changed. When one front wheel is lifted
off the ground, plac ing the Automatic
Transmission in "P" (Park) will
not prevent
the vehicle from moving.
- Before you change a wheel, be sure the
ground is level and firm . If necessary, use a
sturdy board under the jack .
- Always store the vehicle tool k it, the jack
and the replaced tire in the luggage com­
partment ¢
page 135.
Emergency assistance
{!) Tips
Before changing the wheel, you must activate
the jacking mode, so that the automat ic con­
tro ls for the Adaptive Air Suspension do not
make it more difficult to lift the vehicle with
the jack ¢
page 261 .
Changing a wheel
When you change a wheel , follow the sequence
described below step-by-s tep and in exactly tha t
order .
l. Activate the vehicle jack mode ¢ page 261 .
2. Remove the decorative wheel cover*. For
more details see also¢
page 260, Decora ­
tive wheel covers
or¢ page 260, Wheels
with wheel bolt caps .
3. Loosen the wheel bolts¢ page 260.
4. Locate the proper mounting point for the
jack and align the jack below that point
¢ page 261 or¢ page 262.
5. Raise the car with the jack¢ page 261 or
¢page 262.
6. Remove the wheel with the flat tire and then
install
the spare ¢ page 263.
7. Tighten all wheel bolts lightly .
8.
Lower the vehicle with the jack .
9. Use the wheel bolt wrench and
firmly tighten
all wheel bolts<=>
page 260.
10. Replace the decorative wheel cover*.
11. Deactivate the vehicle jack mode in the MMI :
I CAR! function button > Car systems contro l
button
> Servicing & checks > Air susp.: jack
mode > Off.
The vehicle jack mode switches off automatically
at speeds above 10 km/h .
..&, WARNING
Always read and follow all WARNINGS and in­
formation
¢ .&. in AB: Raising the vehicle on
page 262
and ¢ page 264.
259

Emergency assistance
After changing a wheel
A wheel change is not complete without the do­
ing the following .
• Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
<=>page 135.
• Check the tire pressure on the spare wheel im­
mediate ly after mounting it.
• As soon as possible, have the
tightening tor­
ques
on all wheel bolts checked with a torque
wrench. The correct tightening torque is 90 ft
lb (120 Nm).
• Have the flat tire
replaced as soon as possible.
@ Tips
- If you notice that the whee l bolts are cor­
roded and difficu lt to turn while changing a
tire, they should be replaced before you
check the tightening torque .
- Drive at reduced speed until you have the
tightening torques checked.
- After changing a wheel, the tire pressure in
a ll four tires must be checked/corrected and
the tire pressure mon itor ing indicator must
be stored in the MMI
c> page 255.
Decorative wheel covers
App lies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 216 Chan gin g a w heel : Removing the whee l cover
Removing
• Insert the hook (provided with the ve hicle tool
kit) in the hole in the wheel hub cover.
• Pull off the
decorative wheel cover c> fig. 216.
260
Wheels with wheel bolt caps
Applies to: vehicles with wheel bo lts with caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed .
Fig. 217 Changing a wheel: removing the wheel bo lt caps
Removing
• Push the plastic clip (provided with the vehicle
tool kit) over the whee l bolt cap until the inner
retainers on the clip align with the edge of the
cover.
• Remove the cap with the
plastic clip (vehicle
tool kit)
<=> fig. 217 .
Refitting
• Place the caps over the wheel bolts and push
them back on .
The caps are to protect and keep the wheel bolts
clean.
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising
the vehicle.
Fig. 218 Chang ing a wheel: loosening the wheel bo lts

Loosening
• Slide the wh eel wr ench onto the wheel bolt as
far as it will go.
• Take tight hold of the
end of the wrench handle
and turn the wheel bolts
counter-cloc kwise
about one single turn in the direction of arrow
<=>fig. 218.
Tightening
• Slide the wheel wrench onto the wheel bolt as
far as it w ill go.
• Take tight hold of the
end of the wrench handle
and turn each wheel bolt
cloc kwise until it is
seated.
A WARNING
- Do not use force or hurry when changing a
wheel· you can cause the vehicle to slip off
the jack and cause se rious personal injur ies.
- Do not loosen the wheel bolts more than
one turn
before you raise the vehicle with
the jack. -You risk an injury.
(D Tips
- Never use the hexagonal socket in the han­
dle of the screwdriver to loosen or tighten
the wheel bo lts .
- If a wheel bolt is
very tight, you may find it
easier to loosen by carefully push ing down
on the end of the wheel bo lt wrench with
one
foot only . As you do so, hold on to the
car to keep your balan ce and take care no t
to slip .
Emergen cy a ssis tanc e
A8: Raising the vehicle
The vehicle must be lifted with the jack first be­
fore the wheel can be removed.
Fig . 219 Sill panels: markings
F ig . 220 S ill: positioning the vehicle jack
• Activate the vehicle jack mode in the MMI:
!CARI function button > Car systems control
button
> Ser vicing & chec ks> A ir su sp .: jac k
mode > On .
• Engage the pa rki ng br ake to prevent your veh i­
cle from rolling unintentionally.
"' Move the
selector l eve r to position P .
"' Find the mark ing (imprint) on the sill that is
nea rest the wheel that will be changed
<=> fig. 219 . Behind t he marking, there is a lift ­
ing point on the sill fo r th e vehi cle jack.
• Turn the
vehicle jack located under the lifting
point on the sill to raise the jack unt il its arm @
<=> fig. 220 is located under the designated plas­
tic mount<=> .&.<=>CD.
"' Align the jack so that its arm@<=>
fig. 220 en­
gages in the designated lifting point in the door
sill and the movable base @ lies flat on the
gro und . The base @ must be
vertical under the
lifting point@.
"' Wind the jack up fu rther until the f lat ti re
comes off the ground ¢..&._ . ""
261

Emerg ency assis ta nce
Position the vehicle jack only under the designat­
ed lifting po ints on the sill
¢fig. 219. There is ex­
actly
one locat ion for each wheel. The jack must
not be positioned at any other location
c> &<=>0.
An uns table su rf a ce under the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground . If necessary
place a sturdy board or similar support under the
jack. On
hard, slippery su rfaces (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c> ,&..
A WARNING
-
-Yo u or your passengers could be injured
wh ile chang ing a wheel if you do not follow
these safety precaut ions:
- Position the vehicle jack only at the desig­
nated lifting points and align the jack.
Otherw ise, the vehicle jack cou ld slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable s urface under the jack
may cause the vehicle to slip off the jack.
Always p rovide a firm base for the jack on
the ground. If necessary, use a sturdy
board under the jack.
- On hard, s lippery surface (such as tiles)
use a rubber mat or similar to prevent the
jack from slippi ng.
- T o help prevent injury to yo urself and yo ur
passenge rs:
- Do not raise the vehicle unti l you are sure
the jack is securely engaged .
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack.
- Changes in temperature or load can affect
the height of the vehicle.
(D Note
Do not lift the vehicle by the sill . Position the
vehicle jack only at the designated lifting
262
points on the sill. Otherwise, your vehicle wi ll
be damaged .
(1) Tips
The vehicle jac k mode sw itches off automa ti­
cally at speeds above 10 km/h.
58: Raising the vehicle
The vehicle must be li~ed with the jack first be ­
fore the wheel can be removed .
Fig. 221 Sill panels : ma rkings
F ig. 222 Sill : pos ition ing the veh icle jack
.. Activate the vehicle jack mode in the MMI :
!CARI function button > Car s yst ems control
button
> Ser vicin g & che cks > A ir su sp .: jack
mode > On .
.. Engage the parking brake to prevent your vehi­
cle from rolling uni ntentiona lly .
.. Move the
select or lever t o positi on P.
.. Find the marking (imprint) on the sill that is
nearest the wheel that will be changed
<=>fig. 221 . Behind the marking, there is a lift­
ing point
on the sill for the vehicle jack.
.. Turn the
vehicl e jack located under the lifting
point on the sill to raise the jack until its arm
@ Ill>

c::> fig. 222 is located under the designated plas­
tic mount
c::> A in AB: Raising the vehicle on
page
262 <=:>(D.
.. Align the jack so that its arm®
c::> fig. 222 en­
gages in the designated lifting point in the door
sill and the movable base ® lies flat on the
ground . The base ® must be
vertical under the
li ft ing po int @ .
.,. Wind the jack up further unt il the fla t tire
c omes off the ground
c::> A in AB: Raising the
vehicle on page
262.
Position the veh icle jack
onl y under the designat­
ed lifting points on the sill
<=:>page 261, fig. 219 .
There is exactly one locatio n for each wheel. The
jack must not be positioned at any other location
c::> .&. in AB: Raising the vehicle on page 262<=:> 0.
An
un stabl e surface under the jac k can ca use the
vehi cle to slip off the jack . Always provide a firm
base for the jack on the ground. If necessary
p lace a sturdy board or similar support under the
jack. On
hard , slippery surfaces (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping
c::> .&. .
A WARNING
-
-You or your passengers could be injured
wh ile chang ing a wheel if you do not follow
these safety precautions :
- Position the vehicle jack only at the desig ­
nated lifting points and align the jack.
Otherw ise, the vehicle jack cou ld slip and
cause an injury if it does not have suffi­
cient hold on the vehicle.
- A soft or unstable surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the ground .
If necessary, use a sturdy
board under the jack.
- O n hard, s lippery surface (such as tiles)
use a rubber mat or s imilar to prevent the
jack from slipp ing.
- To help prevent inju ry to yourself and your
passenge rs:
- Do not raise the vehicle unt il you are sure
the jack is secure ly engaged .
Emergen cy a ssis tanc e
-Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traffic.
- Make sure jack position is correct, adjust
as necessary and then continue to raise
the jack .
- Changes in temperature or load can affect
the height of the veh icle.
(D Note
Do not lift the vehicle by the si ll. Position the
vehicle jack on ly at the designated lift ing
points on the sill. Otherwise, your veh icle w ill
be damaged.
@ Tips
The vehicle jack mode switches off automati­
cally at speeds
above 10 km/h.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig . 223 Cha ngin g a w heel: us ing the screwdriver handle
(wit h the b lade removed) to turn th e bolts
Fig. 224 Changing a w hee l: a lig nment p in in side the top
hole
263

After you change a tire:
- Check the tire pressure on the spare immedi­
ately after in stallation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
s ible by your authorized Audi dealer or a
qualified servi ce stat ion .
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of 90
ft lb (120 Nm).
- If you notice that the wheel bolt s are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque .
- Replace the flat tire with a new one and have
it installed on you r vehicle as soon as possi­
ble. Remount the wheel cover .
Until then, drive with extra care and at reduced
speeds.
& WARNING
- If you are going to equ ip your vehi cle w it h
t ir es o r rims which differ f rom those which
we re factory installed, then be s ure to read
the info rmat io n ¢
page 243.
- Always ma ke sure the damaged whee l or
even a flat tire and the jack and tool kit a re
prope rly secured in the luggage com part ­
me nt and are not loose in t he passenger
compar tment.
- In an accident o r sudden maneuver they
cou ld fly forward, inju ring anyone in the ve­
hicle.
- Always store damaged whee l, jac k and too ls
sec urely in the luggage co mpartment . Oth ­
erwise, in an accide nt or sudd en man euver
they could fly fo rw ar d, ca usin g injury to p as­
sengers i n the vehicle .
-
Emergency assistance
265

Jumper cables . . . . . . . . . . . . . . . . . . . . . . . . 272
K
Key
Battery replacement master key . . . . . . . . .
31
Key not recognized . . . . . . . . . . . . . . . . . . . 83
Key replacement . . . . . . . . . . . . . . . . . . . . . 30
Mechanical key . . . . . . . . . . . . . . . . . . . . . . . 31
Kick-down (automatic transmission) . . . . . . 115
Knee airbags . . . . . . . . . . . . . . . . . . . . . . . . . 160
Description . . . . . . . . . . . . . . . . . . . . . . . . . 160
How they work . . . . . . . . . . . . . . . . . . . . . . 161
Important safety instructions . . . . . . . . . . 162
L
Lane Change Assistant
refer to Side ass ist . . . . . . . . . . . . . . . . . . . 102
LATCH . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Description . . . . . . . . . . . . . . . . . . . . . . . . . 181
Guidance fixtures for lower anchorages . . 182
Install ing a child restraint . . . . . . . . . . . . . 183
Location . . . . . . . . . . . . . . . . . . . . . . . . . . . 181
Mounting and releasing the anchorage
hook . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
183
Leather cleaning/protection . . . . . . . . . . . . 209
Leaving hom e . . . . . . . . . . . . . . . . . . . . . . . . . 48
Lifting jack . . . . . . . . . . . . . . . . . . . . . . 261, 262
Light
Ambience lighting . . . . . . . . . . . . . . . . . . . .
50
Coming/Leaving home . . . . . . . . . . . . . . . . . 48
Daytime running lights . . . . . . . . . . . . . . . . 46
Emergency flashers . . . . . . . . . . . . . . . . . . . 47
H eadlight range control . . . . . . . . . . . . . . . 46
High beam . . . . . . . . . . . . . . . . . . . . . . . . . . 48
H igh beam assist . . . . . . . . . . . . . . . . . . . . . 49
Interior/r eading lights . . . . . . . . . . . . . . . . 50
Low beam . ................... ..... .. 46
Rear fog lights . . . . . . . . . . . . . . . . . . . . . . . 46
Side marker lights . . . . . . . . . . . . . . . . . . . . 46
Turn signals . . . . . . . . . . . . . . . . . . . . . . . . . 48
Light/rain sensor
Headlig hts . . . . . . . . . . . . . . . . . . . . . . . . . .
46
Intermittent (windshield wipers) . . . . . . . . 54
Sensor defective . . . . . . . . . . . . . . . . . . . . . . 22
Index
Lighting
Exterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
46
Interior . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Loading the roof rack . . . . . . . . . . . . . . . . . . . 71
Locking
Luggage compartment lid . . . . . . . . . . . . . .
36
Power locking switch . . . . . . . . . . . . . . . . . . 35
Remote control . . . . . . . . . . . . . . . . . . . . . . 33
Using the key . . . . . . . . . . . . . . . . . . . . . . . . 35
Low beams . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Luggage compartment
Luggage compartment net . . . . . . . . . . . . .
68
Pass-through with ski sack . . . . . . . . . . . . . 69
Storing cargo cor rectly . . . . . . . . . . . . . . . 135
Stowing luggage . . . . . . . . . . . . . . . . . . . . 135
Tie-downs . . . . . . . . . . . . . . . . . . . . . . . . . . . 68
Luggage compartment lid
Automatic operation . . . . . . . . . . . . . . . . . .
37
Emergency release . . . . . . . . . . . . . . . . . . . . 39
Movement-activated opening . . . . . . . . . . . 39
Opening and closing . . . . . . . . . . . . . . . . . . 36
Lumbar support
Front seats . . . . . . . . . . . . . . . . . . . . . . . . . .
60
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
M
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . 281
Malfunction Ind icator Lamp (MIL) . . . . . 20, 28
Massage function
Front seats . . . . . . . . . . . . . . . . . . . . . . . . . .
60
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . 61
Reclining rear seat . . . . . . . . . . . . . . . . . . . . 63
Matte finish paint cleaning . . . . . . . . . . . . . 206
Mechan ica l key . . . . . . . . . . . . . . . . . . . . . . . . 31
Memory function . . . . . . . . . . . . . . . . . . . . . . 65
Mirrors
Adjusting the exterior mirrors . . . . . . . . . . .
51
Compass.. .. .. .. .. ............... .. . 56
dimming .. .... .. ................. .. . 52
Vanity mirrors . . . . . . . . . . . . . . . . . . . . 53, 54
Monitoring the Advanced Airbag System . . 156
Multifunction steering wheel . . . . . . . . . . . . . 24
N
Natural leather
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . .
209
291