Instrumen ts and ind icator ligh ts
the I SET! button, you de lete the warning thresh
old.
Digital clock with date display and
Odometer
F ig . 5 Ins trum en t cluster: odo meter
Fig . 6 Instrument cluster: reset bu tton
Digi tal clock/GP S controll ed cl ock*
Depending on the vehicle equipment level, you
may choose between the quartz clock or the
GPS
controlled clock* l!j in the radio or in the MMI *.
You can learn more about this in the MMI manual
or in the rad io user 's manual.
Odometer /t ri p odomete r
The display of distance driven is shown in kilome
ters "km" or in miles "mi".
- USA mode ls - Miles
- Canada models - Kilometers
The units of measure (kilometers/miles) can be changed in the radio or MMI* . You can learn
mo re about this in the MMI manual or in the ra
d io user's manual.
The odometer @ shows the total number of kilo
meters or miles that have been driven on the ve
h icle .
12
The trip odometer @ shows the distance driven
since it was last reset.
It can be used to measure
short distances. The last digit shows distances of
100 meters or 1/10 of a mile .
The trip odometer can be reset to zero by press
ing the reset button
!O.O I ¢ fig. 6.
Malfunction message
If there is a malfunction somewhe re in the in
strume nt cluster,
DEF w ill appear in the tr ipod
ometer and w ill stay on. Contact yo ur authorized
Aud i dealer to have the prob lem corrected.
Immobilizer
When the ignition is switched on, the data on the
i gnition key are scan ned automat ica lly .
If an unauthor ized key was used,
SAFE is d is·
played permanently in the odomete r display
field . The vehicle cannot be operated
¢ page 32 .
{i) Tips
-When you switch off the ignition or open
the driver door, the time, date, odometer
and tempe rature are displayed for an addi
tional
30 seconds.
- You can also call up the display with the
!SE T! button¢ page 11 while the ignition is
switched off .
Fuel gauge
The fuel gauge works only when the ignition is
on.
When the needle re aches the red area, the warn
i ng l ight
li'J in the instrument cluster wi ll illumi
nate ¢
page 20. Time to refuel!
The tota l tank capacity of your ve hicle is listed in
¢ page 242.
(D Note
Neve r run the tan k comp letely dry! An ir regu
l a r supply of fuel can cause eng ine misfiring
and fuel could enter in to the exhaust system .
The cata lytic conver ter cou ld the n overheat
and be damaged.
.... N
0 I-co ....
This warning/i ndicator light monitors the ABS
and the electronic differential lock (EDL) .
The warning/indicator light fIE) (USA models)/
ti] (Canada models) wi ll come on for a few sec
onds when the ig nition is switched on. The ligh t
w ill go out after an au tomatic check sequence is
comp leted.
There is a malfunction in the ABS when :
-The warning/indicator lig ht does not ill uminate
when you switch the ig nition on .
- The warning/indicator light does not go out af
ter a few seconds.
- The warning/indicator lig ht ill uminates wh ile
driv ing .
The ESC indicator light a lso ill uminates if the re is
a ma lf u nction in the ABS. The message
Stabiliza
tion control (ESC ): Fault! See owner's manual
als o appears in the inst rument cluste r display
and a warn ing tone sounds.
The brake system will still respond even with
out the assistance of the ABS system. See your
authorized Audi dealer as soon as possible to re
store full braking performance.
For mo re infor
mat io n regarding the ABS
c::> pag e 170.
M alfunction in the brake system
If the b rake warning light c::> page 15 and the ABS
warn ing illuminate
together there may be a ma l
function in the ABS , and there may also be a ma l
function in the b rake system itse lf
c::> .&. . The ABS
will not work and you will notice a change in braking respon se and performance.
In the event of a malfunction in the brake sys
tem
the warn ing/ indicator light 1111 (USA mod
e ls)/ . (Canada models) in the instrument clus
ter f lashes
r:::;, page 15 .
Malfunction in the electronic differential
lock (EDL)
The EDL works toget he r with the ABS . The ABS
war ning light w ill come on if there is a ma lf u nc
tion in the ED L sys tem
c::> page 1 70 . See your au
t h oriz ed A udi de aler as soon as poss ib le .
Instruments and ind icator lights
A WARNING
- If the fIE) (USA mode ls)/ tl] (Canada mod
els) warning light does not go out, or if it
comes on while dr iv ing, the A BS system is
not working prop erly. The veh icle can t hen
be s toppe d only wi th the s ta nd ard brake s
(wit hou t A BS). Y ou will no t have the pro te c
t ion A BS provi des . Cont act your aut hor ized
Au di deale r as soon as possible.
- US A mode ls: I f th e 1111 warning light and
the
9 warn ing ligh t come on togethe r, the
rear w heels could lock up fi rst under hard
braking . Rear wheel lock- up can cause loss
of vehicle contro l and an acc ident. Have yo ur
veh icle repaired immediately by your au
thorized A udi dealer or qualified workshop .
Drive s low ly an d avoid sudd en, hard brak e
ap pli catio ns.
- Canada models : If the brake warn ing light
• and t he A BS warning ligh t
tlJ come on
toge ther, th e re a r wh ee ls cou ld loc k up first
un der hard b raking. Rea r whee l lo ck- up can
c a use l oss of ve hicle con trol and a n acci
dent . Have your ve hicl e repaired immedia te
ly by your a uthorized Audi dea ler or q uali
fied workshop. D rive slowly and avoi d sud
den, ha rd brake applications.
tli I !i: Safety systems
The fl (USA models)/ EI (Canada mode ls) indi
cator lig ht monitors the safety systems (e.g. a ir
bags, pretens ione rs) and illum inates fo r a few
seco nds each time you swi tch the ignition on.
If the
II (USA models) tEI (Canada models) in
dicator light does not go out, o r if it ill uminates
wh ile you a re dr iv ing, or if it sta rts to b link, t hen
t h ere is a malfunct io n somewhere in the system .
If the ligh t does not illum inate wh en yo u sw itc h
t h e igni tion o n, t his a lso means there is a mal
funct ion.
A WARNING ~
If yo u have a ma lf u nct ion in the safe ty sys-
tems, contact your authorize d Au di d ealer im
mediately. Ot herwise the safety systems may
not wor k properly in an accident .
19
Driver information system
Trip computer
Introduction
The trip computer gives you information on cur
rent and average fuel mileage , average speed ,
fu el range and driving time .
Fig. 9 Tri p computer display: Average fu el mile age
~ 9 a: CX) m
The fo llow ing information is contin uously evalu
ated by the trip computer and can be displayed
sequent ia lly in the instrument cluster display:
Fuel range
The estima ted cruising range i n miles (km) ap
pea rs in the disp lay . Th is tells you how far your
veh icle w ill be able to travel on the c urrent tank
of fuel and with the same driv ing style. The dis
p lay changes in increments of 5 miles (10 km).
T he cruising range is calcu lated based on the fuel
consumption for the last 18 m iles (30 km). If you
drive conse rvatively, the cru is ing range will in
crease.
Average fuel mileage
T he avera ge f uel economy in M PG (l/ 100 k m)
since you last clea red the memory a ppears in this
d isp lay . You can use this display to adj ust your
driving technique to achieve a desired mileage .
Current fuel mileage
The instant aneous f ue l cons umption in miles per
ga llon (l/100 km) is shown in this display. Yo u
can use t his disp lay to adjust yo ur driving techni
que to ach ieve a desired mileage .
F ue l cons umption is recalcu lated at inte rv a ls of
33 y ards ( 30 meters) . T his d isp lay sw itches to
ga llons/ho ur ( liters/hour) when the vehicle is not
mov ing.
24
Average speed
The average s peed in mp h (km /h) s in ce you last
rese t the memory appears in t he d isplay .
Elapsed time
The length of time that yo u have been drivi ng
s ince you la st reset t he memory appears in this
display .
Distance
The distance that has been covered since the last
time the memory was cleared appears in the dis play .
0) Tips
-Fuel consumptio ns (ave rage and current),
range and speed are disp layed in metric
units on Canad ian mode ls .
- All stored values will be lost if the vehicle
bat tery is discon nect ed.
Memories
The trip computer is equipped with two fully au
tomatic memories as well as an efficiency pro
gram* .
Fig. 10 Trip computer display: memory level 1
You can sw itch between the t rip computer 1 and
2 and the efficiency program* by pressing the
IRESET I button@c:>page 25, fig. 11.
You can te ll w hich memory leve l is cur rently a c-
tive by the number or the sig n in the display
¢fig. 10 . The data from the single-trip memory
(memory leve l 1) is being d isp layed if a
D ap-
pears in the display. If a
fJ is shown, then the da
ta from the tota l-tr ip memory is being d isp layed .,..
Driver information s ystem
Fuel economy messages
Applies to vehicles: with trip computer with efficiency pro
gram
F ig. 16 D isplay: fuel eco nomy message
Fue l economy messages are displayed when fue l
consumption is inc reased by certain conditions. If
you follow these fuel economy messages, you can reduce your vehicle's consumption of fuel. The
messages appear automatically and are only dis
p layed in the eff iciency program . The fuel econo
my messages turn off automat ica lly afte r ace r
tain period of t ime.
"' To turn a fuel economy message off immed i
ate ly after it appears , press t he I R ESE T I button
¢ page 25, fig. 11 @ , or
"' Press t he f unct ion sele ct io n sw itch
~ page 2 5,
fig. 11
® ·
(D Tips
- Once you have t urned a fue l economy mes
sage off, it will on ly appea r again after you
turn the ig nition on ag ain.
- T he fuel economy messages a re not d is
p layed in every ins tance, but rather in in ter
v al s over a per io d of t ime.
Service interval display
The service interval display reminds you when
your next service is due .
The schedule for the next oil change o r inspec
tion is calc ulated a utomatically and displayed ac
cord ingly. The display works in two stages:
28
Service reminder
3 0 days before the next service is due , a servi ce
r eminder appears in the display when you turn on
the ignition .
After abou t
5 seconds the display swit ches bac k
to normal. The dist ance a nd time rem aining are
u pda ted each time the ignit ion is turned on unt il
the date due for service is reached.
Service due
Whe n the d ue date for se rvice is rea ched, the
message
Service due! appears in the inst rument
cl uster immed iate ly after you tu rn o n the igni
tion . Add itiona lly, a warn ing tone sounds. A fter
about
5 seconds the display switches back to nor
mal.
Calling up the service schedules
I f or w hen an oil change o r inspec tion is due, can
be shown in the radio or MMI * display by se lect
i ng the service interval display in the car menu.
Se lect
I CAR I fu nction button > Se rvice interval
display
or ! CAR I function button > Car systems *
control button > Ser vicing & checks .
Resetting the s ervice interval display
Yo ur a utho rized Aud i dea ler will rese t the corre
sponding service schedu le after performing the
approp riate service on your vehicle . You also have
the possibility to reset t he oi l change schedule
after having pe rformed an oil change accord ing
to Audi specifications. Select
I CA R I fu nction but
ton
> Service interval display > Re set oil change
interval
or ICA RI fu nction button > Car systems *
control button > Servicing & check s > Reset oil
change interval.
(D Note
- Only reset the oil c hange display when you
h ave completed an o il change.
- If you disconnect the battery term inals, no
calcu lations can be made for the se rvice in
te rv al display dur ing th is time and no se rv
i c e rem inder will appear. Remembe r th at
ob serv ing the pro per serv ice intervals is vi-
ta lly im po rt an t to extending the life o f your .,.
-Do not remove the key from the ignition
lock until the vehicle has come to a com
plete stop . Otherwise the steer ing column
lock could suddenly engage -causing the
risk of an accident .
(D Tips
-The operation of the remote control key can
be temporarily d isrupted by interference
from transmitters in the vicinity of the vehi
cle work ing in the same frequency range
(e .g. a cell phone, radio equipment).
- For security reasons, replacement keys are
only available from authorized Aud i dea ler .
- For Declaration of Compliance to Un ited
States FCC and Industry Canada regulations
<::>page 247.
Removing the mechanical key
F ig. 19 Remote master key: removing t he m ec hani ca l key
.,. Press the release button @r=> fig. 19.
.,. Pull the mechan ical key ® out of the master
key.
Using the mechan ical key, you can :
- lock and unlock* the glove compartment on the
passenger's side
c> page 61 .
-lock and unlock the lockable rear bench seat
and pass-through
c> page 64.
- lock and unlock the vehicle manually
c> page 36 if this should not be possible with
the master key.
- use the ign ition key emergency release
;::; opage 34.
0 1-CX)
rl I.Cl U"I
rl I.Cl rl
Open ing and closing
Check light and battery in the master key
Fig. 20 Remote master key: re moving the bat tery holder
Check light in the master key
The check light @r=> fig. 20 in the master key
provides information about d ifferent conditions .
.,. The check light turns on briefly once when a
button is pressed, and during an "inquiry" by
the convenience key system.
.,. If the check light does not come on, the battery
is dead and has to be replaced . In addition,
when the battery is dead the
Ill indicator light
appears in the instr ument cluster display as
well as the message
Please change key bat
tery .
Master key battery replacement
.,. Remove the mechanical key o page 33 .
.,. Press the re lease button ® o fig. 20on the bat
t ery holder and at the same time pull the ba t
tery holder out of the master key in the d irec
tion of the arrow .
.,. Insta ll the new battery CR 2032 with the"+"
sign facing down .
.,. Push the battery holder carefully into the mas
ter key .
.,. Install the mechanical key.
@) For the sake of the environment
Dispose of dead batteries properly so as not
to pollute the environment.
@ Tips
The replacement battery must be the same
specificat ion as the original.
33
Light and Vision
The coming home and leaving h ome functions
only operate when it is dark and t he light switch
is in the AUTO position
~ page 44, fig. 36.
Auto headlights*
W hen the light swi tch is in the A UTO ~ page 44
position, the sw itch-on po int of the lights can be
cha nged in the automatic driving light function.
Daytime running lights
USA models :
You can switch the daytime r unning
lights
on and off .
Canada models: The funct ion cannot be tu rned
off .
It is activated automatically each t ime the ig
n ition is switched on.
Tra vel mode*
The headlight beam is asymmetrical. This pro
vides stronger illumination on the side of the
road on which you are driving.
If you are driving
in a cou ntry that dr ives on the opposite side of
the road from you r own country, this will cause
g lar e fo r oncom ing dr ive rs . To p revent glare:
- Travel mode must be selected in veh icles w ith
Xenon headlights* .
- In vehicles with halogen headlights, certain
areas of the headlight lenses must be cove red
with waterproof adhesive covers that prev ent
l ight from passing through. For more informa
tion, ple ase see you r auth orized Audi dea le r or
a uthorized repair fa ci lity .
When travel mode is ac tiva ted, a disp lay in
t he dr ive r inf orm ation sys tem in dicates this
e ach t ime yo u sw itch the ignition on .
46
Emergency flashers
Fig. 38 Center console: emergency flashe r switc h
The emergency flashers makes other motorists
aware that you or your ve hicle are in an emergen
cy situat io n .
.. Press the switch~¢
fig. 38 to turn the emer-
gency flashers on or off .
When the emergency flashers are on, all four
turn s ignals b link at the same time. The turn sig
nal indicator lights
RB i n the instrument clus
ter, as well as the light in t he emergency flasher
switch
IA] blink likewise .
You can indicate a lane change or a turn when the
emergency flashers are switched on by using the
turn signal lever . The emergency flashers stop
tempora rily .
The emergency flashe rs a lso wor k when the ign i
tion is turned off.
The emergency flashers will turn on automatical
l y if you a re in an accident where the airbag has
deployed .
@ Tips
You should turn on the emergency flashers
when:
-you are the last vehicle standi ng in a traffic
jam so that any other vehicles com ing can
see yo u, or when
- yo ur ve hicle has broken down or yo u are in
an eme rge ncy sit uat ion, or w hen
-your vehicle is be ing towed by a tow tru ck or
if yo u are towing another vehicle behin d
you.
.... N
0 Ico ....
cause a crash and personal injury.
- Only mount the roof rack on the designated
locations on the roof
c:> fig . 65.
- The roof rack system must be installed ex
act ly according to the instructions provided .
- When driving with a roo f rack system,
changes to the center of gravity and wind
resistance can change the vehicle handling
and lead to a collision. Always adapt your
dr iv ing and your speed to the current condi
t ions .
- Your vehicle warranty does not cover any
damages to the vehicle caused by using roof
racks or mounting structures not approved
by Audi for your vehicle . The same applies to
damage result ing from incorrect roof rack
i nstallation .
-Always check the roof rack mount ings and
hardware before each t rip and dur ing a tr ip
to make sure everyt hing is securely tight
ened.
If necessary, ret igh ten the mo unt ings
and c hec k the en tire system from time to
time.
- After mounting a roof rack system, or when
you transport objects on the roof of your ve
hicle, the height of the vehicle is naturally
increased . Be careful when driving under
l ow bridges or in parking garages for exam
ple. This could cause damage to the load
and even the vehicle itself.
- Make s ure that the open rear lid and the
sunroof do not come into contact with ob
jects on the roof .
Loading the roof rack
Always distribu te loads evenly. Make sure any
thing on the roof rack is securely tied down.
~ Always distribute th e loads on the roof rack
evenly .
~ Always attach items to the roof rack securely
before you drive off .
T he maximum perm iss ible roof weight is
165 lb
( 75 kg ). The roof weight is the total of the
Seat s and sto rage
weight o f the roof rack, the attachments and the
cargo you ar e carrying. You must a lso not exceed
the max imum load weight for the roof rack you
are using.
When using a roo f rack system which has a lower
load carry ing capacity, you must not use up the
total max imum permissible load carry ing capac i
ty specified above. Instead, you should load the
roof rack sys tem only to the maximum capacity
specified by the manufacturer of the roof rack
system .
A WARNING
= -Weak, damaged or imprope r straps used to
secure items to the roof rac k can fail d uring
hard brak ing o r in a co llision and cause seri
ous persona l injury.
- Make sure the roof r ack is installed exactly
as specified above
c:> page 62.
- Always use suitable mounting straps fo r se
cur ing items to the roof rac k to he lp prevent
items from shifting o r flying forward .
- Items on the roof rack mus t always be se
curely mounted.
- The use of a roof rack can negative ly affect
the w ay a vehicle hand les . Cargo tha t is
large, heavy, b ulk y, long or flat wi ll have a
grea ter negat ive infl uence on the vehicle's
aerodynamics, center of gravity and overa ll
handling. Always drive slowly, avoid sudden
braking and maneuvers when transporting
cargo on the roof of your vehicle.
- Never exceed the max imum permissib le
load carrying capacity of the roof of your ve
h icle, the permiss ible axle weights and the
perm iss ible total we ight of your vehicle
c:> page 241, Weights .
@ For the sake of the environment
As a result of the increased wind res istance
created by a roof rack, your vehicle is using
fuel unnecessarily . So remove the roof rack
after using it .
63
Emergency braking
In the event that the conventional brake system
fails or locks.
11-In an emergency, pull the sw itch @c:> page 77,
fig. 80 and cont inue to pull it to slow your vehi
cle down with the park ing brake .
11-As soon as you release the switch @ or acceler-
ate, the brak ing p rocess stops.
If you pull the sw itch @and hold it above a
speed of about
5 mph (8 km/h), the emergency
braking function is in itiated. The vehicle is braked
at all four wheels by activating the hydrau lic
b rake system. The brake performance is sim ila r
to making an eme rgency stop c:>
.&..
In order not to activate the emergency brak ing by
mistake, an audib le wa rning tone (buzze r)
sounds when the sw itch @ is pulled . As soon as
the switch @is re leased, or the acce lerator peda l
is depressed, emergency braking stops.
A WARNING
Emergency braking should only be used in an
emergency, when the normal foot brake has
failed or the brake pedal is obstructed. Using the parking brake to perform emergency
brak ing will slow your vehicle down as if you
had made a full bra ke appl ication . The laws of
physics cannot be suspended even with ESC
and its associated components (ABS, ASR, EDS). In corners and when road or weather
conditions a re bad, a f ull brake application
can ca use the vehicle to skid or the rear end to
break away- risking an accident.
Speed warning system
Overview
The speed warning sys tem helps you to keep your
driving speed below a set speed limit .
The speed warning system warns if the driver ex
ceeds a prev iously stored maximum speed. A
;::; warning tone w ill sound as soon as the vehicle
0 ~ speed exceeds the set speed by about 3 mph
~ (3 km/h). At the same time , a warning symbol Lil ,...., v:, ,....,
D riv ing
appea rs in the display. The symbo l's appearance
might be diff erent in some models.
T he speed warn ing system has two warning
thresholds that function independently of each
othe r and that have somewhat different p urpos
es:
Speed warning 1
You can use speed warning 1 to set the max imum
speed w hile you are dr iving . T his sett ing will re
main in effect until you tu rn off the ignit ion, as
sum ing that you have not changed o r reset the
setting .
T he . (USA models) /. (Canada models)
speed wa rning symbo l in the warning 1 disp lay
appears when you exceed the maximum speed .
It
goes out when the speed falls below the stored
maximum speed.
T he speed warn ing symbol will also go out if the
speed
exceeds the stored maximum speed by
more than about 2S mph
(40 km/h) for at least
10 seconds. The stored maximum speed is delet
ed.
Sp eed wa rning 2
Storing warning 2 is recommended if you always
want to be reminded of a certain speed, for ex
amp le wh en you are trav eling in a country that
has a genera l maximum speed limit, or if you do
not want to exceed a specified speed for winter
t ires .
T he . (USA models) /. (Canada mod els)
speed warning 2 symbol appears in the display
when you exceed the stored speed limi t. Unlike
warning 1 , it wilt not go out unt il the vehicle
speed drops below the stored speed limit .
Setting speed warning 2 c:>
page 80.
{D Tips
Even though your vehicle is eq uipped with a
speed warning system, you should still watch
the speedometer to make sure you are not
driving faster than the speed lim it.
79