2016 AUDI A3 water

,....,
N
0 > co ,...., & WARNING
-Only wash the vehicle when the ignition is
off and follow the instructions from the car
wash operator to reduce the risk of acci­
dents.
- To reduce the risk of cuts, protect yourself
from sharp metal components when wash­
ing the underbody or the inside of the wheel
housings.
-After washing the vehicle, the brak ing effect
may be delayed due to mo isture on the
brake rotors or ice in the w inter . The brakes
must be dried first w ith a few careful brake
applica tions .
{[) Note
-If you wash t he vehicle in an automatic car
wash, yo u m ust fold the e xterior m irrors i n
to reduce the risk of damage to the mi rrors.
Power folding exte rior m irrors* must o nly
b e fo lded in a nd out usin g the power folding
f u nct io n.
-
Ca re and cleaning
- To prevent pa int damage, do not wash the
vehicle in direct s un light .
- To re duce the risk of damage to the surface,
do not use insect removing sponges, kitche n
sponges o r similar items .
- Matte finish painted veh icle components:
- To reduce the r isk of damage to the sur-
face, do not use po lish ing agents or hard
wax.
- Never use protective wax. It can destroy
the matte finish effect .
- Do not place any stickers or magnetic
signs on vehicle parts painted with matte
finish paint . The paint cou ld be damaged
when the stickers or magne ts are re ­
moved.
@ For the sake of the environment
Only wash t he veh icle in facili ties s pec ially de­
s igned for that pu rpose . This will reduce the
r isk of dirty wate r contamina ted with o il from
ente ring the sewe r sys tem.
Cleaning and care information
W hen clea ning and ca ring for individua l vehicle
comp onents, refer to the following t ables. The
inf ormat ion cont ained there is s imp ly recom ­
mendations. For q uest ions or for components t
h at are not l isted, cons ult an autho riz ed Aud i
de aler or author ized A udi Se rvice Fa cility. Also
f o llow the information fo und in ~ .&. .
Ext erior cleaning
Component Situation Solution
Windshield wiper
D eposits ~ page 53, Cleaning windshield wiper blades
blades
Headlights /
Deposits So
ft spo nge with a m ild soap solutiona)
Tail lights
Sensors /
Deposits Sensors: soft cloth w ith solvent-free cleaning solution
camera lenses Camera lenses: soft cloth w ith alcohol-free cleaning solu-
tion
Snow/ice Hand br
ush/solven t-free de -icing spray
Wheels Road salt Water
Brake dust Acid-free special clean
ing so lution
Exhaust tail p ipes Road salt Water, clea ning so lu tion su itab le for s tainless stee l, if nee-
essary
Decorati ve parts / Deposits Mild soap so lution a>, a cleaning solution su itable for stain-
Trim less stee l, if necessary
275
...

Care and cleaning
Component Situation Solution
Paint
Paint damage Refer to the paint number on the vehicle data label, repair
with touch up paint¢
page 301
Spilled fuel Rinse with water immediately
Surface rust Rust remover, then protect with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv-
ice Facility.
Corrosion Have
it removed by an authorized Audi dea ler or a uthor-
ized A udi Service Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith water immediately and remove with a micro-
sects, bird dropp ings, f iber cloth
tree sap and road salt
Grease-based con- Remove immediately wi th a mild soap solution al and a
taminants such as
soft cloth
cosmetics or sunblock
Carbon parts Deposits clean the same way as painted parts¢ page 2 74
Decorative decals Deposits Soft sponge with a mild soap solutional
Audi e-tron Deposits Dry towe l
charging system *
Charging dock*
Deposits Soft towel with alcoho l-free cleaning so lution
a} Mild soa p sol ution: maxim um two tablespoons of neutral soap in 1 quart (I liter) of water
Internal cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild soap solutional
Trim
Plastic parts
Deposits Damp cloth
Heavier deposits Mild soap so lution al, detergent-free p lastic clean ing solu-
tion, if necessary
Displays Deposits Soft cloth with LCD cleaner
Controls Deposits Soft brush, then a soft cloth with a mild soap solutional
Safety belts Deposi ts Mild soap solution al, allow to dry before letting them re-
tract
276

,..,
N
0 > co ,.., Care and cleaning
Component Situation Solution
T ex til es
Deposits adhering to Vacuum cleaner
art ificial l eather, the surface
A lcan tara Water-based deposits Absorbent
cloth and mild soap solutiona>
such as coffee, tea,
b lood, etc.
Oil -based deposits Apply a m ild soap solution
a), blot away the dissolved o il or
such as oil, make-up, dye, treat afterward with water, if necessary
etc.
Special deposits such Special stain
remover, blot with absorbent material, treat
as ink, nail polish, la- afterward with mild soap solution, if necessary
a)
tex paint, shoe pol-
ish, etc.
Natu ral le ath er Fresh stains Wool cloth with a mild soap solution a)
Water-based deposits Fresh stains: absorbent cloth
such as coffee, tea, Dried stains : stain
remover suitable fo r leather
b lood , etc.
Oi [-based deposits Fresh stains: absorbent cloth and stain
remover suitable
such as oil, make-up, for leather
etc. Dried stains : grease dissolving spray
Special deposits such Spot remove r suitab le for leather
as ink, nai l polish, la-
tex paint, shoe pol-
ish, etc.
Care Regularly apply condit ion ing c ream that protects from
lig ht and penet rates into the material. Use specia lly-co l-
ored conditioning cream, if necessary .
Carbon part s Deposits clean the same way as plast ic parts
a) Mi ld soap solution: maximum two tablespoons of neutral soap in 1 q uart (1 liter) of water
.8, WARNING
The windshield may not be trea ted with wa­
ter-repelling windshield coating agents. Un ­
favorable cond itions such as wetness, dark­
ness, or low sun can result in increased glare.
Wiper blade chatter is also possible.
A WARNING
- Audi e -tron charg ing sy stem *
- Never immerse the charging system and
connectors in water.
- The charging system m ust only be cleaned
when the control unit is completely d is­
connected from the powe r su pply system
and from the vehicle.
-
({I) Note
- Hea dlight s/tail lights
- Never clean headlights or tail lights w ith a
d ry cloth or sponge.
- Do not use any cle aning product that con­
tains alcoho l, because they could ca use
cracks to form.
-Whe els
- Never use any pa int polish or other abra-
sive materials.
- Damage to the protect ive layer on the
rims such as stone chips or scratches must
be repaired immediately .
-Sensor s/came ra le nses Ill-
277

Care and cleaning
- Never use warm or hot water to remove snow or ice from the camera lens. This
cou ld cause the lens to crack.
- Never use abrasive clean ing mater ia ls or
alcoho l to clean the camera lens. This
cou ld cause scratches and cracks.
- Door windo ws
- Remove snow and ice on windows and ex -
terior mirrors with a p lastic scraper. To
avoid sc ratches, move the scrape r on ly in
one direction and not back and forth .
- Never remove snow o r ice from doo r win­
dows and m irrors using warm or hot water
because this could cause cracks to form.
- To avoid damage to the rear w indow de­
fogge r, do not apply any sticke rs on the
heating w ires on the inside of the window.
- Decorative parts /trim
- Never use chrome care or cleaning prod-
ucts.
-Paint
-To reduce the risk of scratches, the vehicle
must be free of dirt and dust before pol ­
ishing or waxing .
- To prevent pa int damage, do not polish or
wax the veh icle in direct sunlight .
- To reduce the risk of pa int damage, do not
polish away rust spots .
- Remove cosmetics and sunscreen immedi­
ately- these could damage the paint.
-Di splays
- To avoid scratches, do not use dry cleaning
methods on displays.
- Controls
- Make sure that no fluids enter the con -
trols, because this could cause damage .
-Safet y belt s
-Do not remove the safety belts to clean
them.
- Never clean safety belts or their compo­ nents chemically or with corrosive flu ids
or so lvents and never allow sharp objects
to come into contact w ith the safety belts .
Th is could cause damage to the belt web­
bing.
- If there is damage to the webbing, the
connect ions, the retractors or the b uck les,
278
have them replaced by an authorized Aud i
dealer or authorized Audi Service Facility.
- Te xtile s/artificial l eath er/ Alcantara
- Never treat art ificial leather/ A lcantara
with leather care products , solvents, floor
polish, shoe polish, spot remove or s imilar
p roducts .
- Have a spec ialist remove stubborn stains
to prevent damage .
- Never use steam cleaners, brushes, hard
sponges, etc . when cleaning .
- Do not turn on the seat heating* to dry the
seat .
- Ob jects w ith sharp edges such as zippers,
rivets on clothing or be lts can cause dam­
age to the surface .
- Open hook and loop fasteners, for exam­
p le on clothing, can damage seat covers .
Make sure hook and loop fasteners are
closed .
-Natural l eather
-Neve r treat leather wi th solvents , floor
polish, shoe polish, spot remover or sim i­
lar products .
- Obje cts w ith sharp edges such as zippers ,
rivets on clothing or be lts can cause dam ­
age to the surface .
- Neve r use s team cleaners, brushes, hard
sponges, etc . when cleaning .
- D o not turn on the seat heating* to dry the
seat.
- To he lp prevent the leather from fad ing,
do not leave the vehicle in d irect sunlight
for long periods of time . If leaving the ve ­
hicle parked for long periods of time, you
should cover the leather to protect it from
d irect sunlight.
{D Tips
- Insects are easier to remove from paint that
has been freshly waxed.
- Regular waxing can prevent rust spots from
forming.

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
both tabs on the side panels ¢ fig. 209 (top im ­
age).
.. A3 Sedan: clip the plastic hook@ into the lug ­
gage compartment seal¢
fig. 209 (bottom im­
age) .
Side panel
.. Open the twist lock and remove the cover @* I
@ ¢fig. 208 .
.&_ WARNING
Improper use of the vehicle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
atta in the necessary tightening torque if you
use the hex head, potentially caus ing an ac­
c ident.
- The factory-supplied jack is intended only
for your vehicle model. Under no circum­
stances should it be used to
lift heavy
vehicles o r other loads; you r is k inju ring
yo urself.
- Never start the engine when the vehicle is
ra ised, whi ch could cause an accide nt.
- Support the veh icle secure ly with app ropr i­
ate stands if wor k is to be perfo rmed under­
neath t he vehicle; otherwise, the re is a po­
tent ial risk for in jury.
- Never use the jack s upplied with your Audi
on another vehicle, par tic ularly on a heav ier
one. The jack is only suitab le for use on the
vehicle it came with .
(D Tips
The vehicle jack* in your vehicle is mainte­
na nee-free.
Tire mobility kit
Preparation
A ppl ies to vehicles: W ith t ire re pair set
.. Read and fo llow th e import ant saf ety pr ecau­
tion s¢
page 280, General information .
.. Check if a repair w ith the t ire mobility k it is pos­
s ible
¢ page 281.
Emergen cy a ssis tanc e
Using the tire mobility kit
App lies to vehic les : With tire r epair set
F ig. 210 T ire: t ire damage t hat cannot be repaired
The tire repair is only meant for temporary use.
Change the spare tire as soon as possible <=>,&. .
If the t ire is p ierced by an object such as a nail,
do not remove the object from the tire.
The tire repair set is ab le to be used at tempera­
tures as low as - 4 °F (- 20 °C).
The t ire mobility kit may not be us ed:
- if the ti re has cuts or punctures that are larger
than
0 .1 6 in (4 mm)@ ¢ fig. 210.
-if the rim is damaged @.
- if you drove with very low t ire pressure or with-
out air in the tire @.
See an authorized Audi dealer or authorized Audi
Service Facility for assistance in these situations .
.&_ WARNING
>=
-Please note that the tire mobility kit cannot
be used in all situations, and that it may on­
ly be used temporarily.
- The tire sealant must not come in contact
wit h skin, eyes, o r clothes.
- If ti re sealant gets in you r eyes or on yo ur
skin, tho ro ughly rinse the affected area im­
mediately wi th clea n wate r.
- Do not inha le the fumes.
- If you swallow any of the tire sealant, thor-
ough ly rinse your mouth immediately and
drink a lot of water . Do not ind uce vomiting.
Seek med ica l attent io n immed iate ly .
- Change yo ur clothes immediately if they get
tire seala nt on them.
~
281

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
No. Equipment
F43 Headlights, lighting
F44 all whee l drive
F47 Rear window wiper
F48 Outer noise amplifier
(Plug-in hybrid
drive*)
Starter, clutch sensor, headlight relay coil,
F49 high-voltage battery (Plug-in hybr id
drive*)
F53 Rear window
defogger
The power seats* are protected via
circuit break­
ers
that automatically switch on after a few sec­
onds after the overload has been reduced.
(D Tips
Note that the following table was accurate at
the time of printing and is subject to change.
Left engine compartment fuse assignment
Fig. 227 Engine compartment: fuse assignment
No. Equipment
Fl ESC control module
F2 ESC control module
F3 Engine control module (gasoline/d iesel)
M ,-..
0
> co ID
Fuses and bulbs
No. Equipment
Engine cooling, engine components, auxili-
F4 ary heater coil relay (1+2), secondary a ir
injection pump relay
FS Engine components, tank system
F6 Brake light sensor
F7 Engine components,
water pumps
F8 Oxygen sensor
F9 Engine
components, exhaust door, glow
time control module, SULEV va lve
FlO Fuel injectors, fuel control modu le
Fll Auxiliary heater heating element 2
F l2 Auxiliary heater heating element 3
Fl3 Automatic transmission control module
FlS Horn
Fl6 Ignition coil/
power electronics (Plug-in
hybrid drive*)
Fl7 ESC control
module, eng ine control mod -
ule
Fl8 Terminal 30 (reference voltage)
F l9 Windshield wipers
F20 Horn
F22 Termina l 50 diagnosis
F23 Starter
F 24 Auxiliary heater heating element 1,
brake
booster (Plug-in hybrid drive*)
F31 Vacuum
pump/water pump (Plug-in hybrid
drive*)
F32 LED
headlights
F33 Brake booster
memory (Plug-in hybrid
drive*)
F 34 Brake
booster control (Plug -in hybrid
drive*)
F 35 Relay (Plug-in hybrid drive*)
@ Tips
Note
that the fo llowing tab le was accurate at
the time of printing and is subject to change.
293

Fuses a nd bul bs
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned out
bulbs for you.
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­
moved before you are able to get to the bu lb .
This applies espec ially to the light bulbs in the
front of your car wh ich you can only reach
through the engine compartment .
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, and parts
m ust be correctly taken apa rt and then p roperly
put back together to help prevent breakage of
parts and long term damage from water that can
enter housings that have not been properly re­
sealed.
For your safety, we recommend that you have
your authorized Audi dealer replace any bu lbs for
you, since your dealer has the proper tools, the correct bulbs and the expertise.
G as di sc harg e l am ps (Xe non li ghts):
Due to the high electrical voltage, have the bulbs
replaced by a qua lified technic ian . Headlights
with Xenon light can be identified by the high­
voltage sticker.
LED headlights* require no maintenance. Please
contact your authorized Aud i dealer if a bulb
needs to be replaced.
A WARNING
Contact w ith high-voltage components of the
electrical system and improper rep lacement
of gas discharge (Xenon) headlight bulbs can
cause serious personal injury and death.
- Xenon bulbs are pressurized and can ex­
plode when being changed.
- Changing Xenon lamps requires the special training, instructions and equipment.
- Only an a uthorized Audi dea ler or other
qualified workshop should change the bulbs
in gas discharge lamps .
294
A WARNING
-
There are parts with sharp edges on the open-
ings and on the bulb holders that can cause
serious cuts.
- If you are uncertain about what to do, have
the work performed by an authorized Audi
dealer or other qualified workshop. Ser ious
pe rsonal injury may resu lt from improperly
pe rformed wor k.
@ Tips
- If you still prefer to replace the light bulbs
yourself, be aware that the engine compart­ ment is a hazardous area to work in
9 page 2369 .&.
-It is best to ask your authorized Audi dealer
whenever you need to change a bulb.

,....,
N
0 > co ,...., Emergency situations
General
This chapter is intended for trained emergency
crews and working personnel who have the nec­
essary tools and equipment to perform these
ope rations.
Starting by pushing or
towing
(D Note
Veh icles with an automatic transmission can­
not be started by pushing or towing.
Starting with jumper
cables
If necessary, the engine can be started by con­
necting it to the battery of another vehicle.
Plug-in hybrid drive*: the connection points for
the jump start cables vary ¢
page 108.
If the engine should fail to start because of a dis ­
charged or weak battery, the battery can be con­
nected to the battery of
another vehicle, using a
pair of jumper cables to start the engine.
Jumper cables
Use only jumper cables of suffic iently large cross
section
to carry the starter current safely. Refer
to the manufact urer 's specifications.
Use only jumper cables with
insulated term inal
clamps which are distinct ly ma rked:
plus (+) cable in most cases colored red
minus (-) cable
in most cases colored black .
.,&. WARNING -
Plug-in hybrid drive*: you must not give a
jump start with your vehicle. This could cause significant damage to the electrical system in
your vehicle ¢
page 108.
Emergency situations
.,&. WARNING
-
Batteries contain electricity, acid, and gas.
Any of these can cause very serious or fatal in­
jury . Follow the instruct ions below for safe
handling of your vehicle's battery.
- Always shield your eyes and avoid leaning over the battery whenever possible.
- A discharged battery can freeze at tempera­
tures just below 32 °F (0 °C) . Before con­
necting a jumper cable, you must thaw the
frozen battery completely, otherwise it
could explode.
- Do not allow battery acid to contact eyes or
skin. Flush any contacted area with water
immed iate ly.
- Improper use of a booster batte ry to sta rt a
veh icle may cause an exp losion .
- Veh icle batteries generate exp losive gases .
Keep sparks, flames and lit cigarettes away
from batteries.
- Do not try to jump start any vehicle with a
low acid level in the battery .
- The voltage of the booster battery must also
have a 12 volt rat ing. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery. Use of
batteries of different voltage or substantial­ ly different "Ah" rating may cause an explo­
sion and personal injury.
- Never charge a frozen battery . Gas trapped
in the ice may cause an explosion.
- Never charge or use a battery that has been
frozen. The battery case may have been
weakened.
- Use of batteries with different voltage or
substantially different Ah rating may cause
an explosion and injury. The capacity (Ah) of
the booster battery should not be lower
than that of the discharged battery .
- Before you check anyth ing in the eng ine
compartment, always read and heed all
WARNINGS
¢page 236.
(D Note
-App lying a higher voltage booster battery
will cause expensive damage to sensitive
295