2016 AUDI A3 warning

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Front passenger's door and rear doors
emergency locking
All doors must be locked separately if the power
locking system fails .
Fig. 25 Em erge ncy doo r loc kin g
The driver's door can be locked using the door
lock cylinder
c:> page 39.
,.,
6
i
The emergency lock on the other doors is located
on the side of the front passenger's and rear
doors. It is only visible when the door is open.
~ Pull the cover cap out of the opening .
~ Insert the key bit in the slot inside and turn the
key all the way to the right (right door) or left
(left door).
Once the door has been closed, it can no longer
be opened from the outside. The door can be un ­
locked and opened from the inside by pulling the
door handle once.
If the child safety lock on the rear doors is act i­
vated, pull the inner door handle first. Then you
can open the door from the outside.
Open ing and closing
Luggage compartment
lid
Opening and closing the luggage
compartment lid
Fig. 26 Luggage compar tme nt lid: opening (hand le)
Fig. 27 Luggage compar tme nt lid/hand le (example): clos ­
ing
Opening the luggage compartment lid
~ Press and hold the l.:::1 1 button on the remote
control key for at least one second, or
~ Push the handle in the luggage compartment
lid
c:> fig . 26, or
~ Pull the ~ button* in the driver's door@
r=!)page 8, fig . 1.
Closing the luggage compartment lid
~ Use the inside grip to pull the luggage com­
partment lid down and allow it to drop gently
to close it
c:> fig . 2 7 c:> £ .
.&_ WARNING
-After closing the luggage compartment lid,
make sure that it is latched. Otherwise the
luggage compartment lid could suddenly
open when driv ing, which increases the risk
of an accident.
.
41

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Power windows
Controls
The driver can control all power windows.
Fig. 30 Driver 's doo r: powe r w in dow contro ls
All power window sw itches h ave a two- stage
function :
Opening the windows
,-. N M 0
:::i co co
• Press the switch to the first level and hold it
u nti l the w indow reaches the desire d position .
• Press t he swi tch b riefly to the
second stop to
au toma tically open the window.
Closing the windows
• Pull the swi tch up to the first lev el and hold it
u ntil the w indow reaches the desired position .
• Pull the swi tch b rief ly to the
s econd stop to au-
tomat ically close the window.
Power window switches
(D Left front doo r
@ Righ t fr ont door
@ Left rear door
© Right rear door
® Safety bu tton
Child safety lock
When the safety button ® is p ressed, the~
s ymbol in t he button t urns on. The power win­
dow switc hes in the re ar doors a re swi tched off.
A WARNING
-Always re move the ign it io n key whe n you
leave yo ur vehicle, eve n for a short period of
t ime. This app lies part icu larly when children
remain in the vehicle. Otherwise the c hil-
Open ing and closing
dren cou ld start the e ngine o r operate elec­
tr ica l equipment such as power windows.
The power windows cont inue to funct io n un­
til the driver's door or fron t passenger's
door has bee n opened.
- Pay careful attention when closi ng the w in­
dows. It co uld cause injury by p inch ing .
- When locking the vehicle from outside, the
ve hicle must be unoccup ied si nce the win­
dows can no longe r be o pened in an emer­
gency.
@ Tips
A fter tu rning the ignition off you can st ill
open and close the windows for approximate­
ly 10 seconds. The power windows are not
sw itched off unti l the drive r's doo r or front
passe nger 's doo r has been opened.
Convenience opening /closing
Wi th the convenience ope ning/closing func tion,
yo u ca n cen tral ly and easily open the windows
and the panorama sun roof * from the outs ide.
Convenience opening
• Press the open button [fil] on t he remote cont rol
key u ntil all wind ows and the pa norama sun­
roof* have reached the desired pos ition, o r
• Ho ld the key in the dr iver's door lo ck until a ll
windows and the panorama s unroof* have
reached t he des ired position.
Convenience closing
• Ho ld the key in the dr iver's door lo ck in the lock
position unt il a ll w in dows an d t he panor am a
sunroof* a re closed .
Convenience closing with the convenience
key*
• Touch the sen so r* on o ne of the front door han­
d les and co nti nu e touching it until all of the
windows and the panorama s unroof* are
closed . Do not place you r hand in the door han­
dle when do ing th is .
43

Opening and clo sin g
Adju st ing the con venien ce op en ing in the
MMI
.. Select: the I MENU ! button >Car > Sys tems*
control button > Vehicle sett ings > Central
l oc king > Lo ng -p res s to open w indows
To enable convenience opening of the w indows
and the roof*, the
front wind ow , rea r wind ow *
and roof * functions must be switched on.
A WARNING
-Never close the windows or panorama sun­
roof* careless ly or in an uncontrolled man­
ner, because this increases the risk of injury .
- For security reasons, the windows can only
be opened with the remote control key at a
maximum d istance of approximately 6 feet
(2 mete rs) from the vehicle.
- Pay attention when using the lock cylinder
to close the windows and the panorama
s u nroof* so that no one is pinched. Closing
stops when the key is moved into the start­
ing position .
Correcting power window malfunctions
-
After disconnecting the vehicle battery, the one­
touch up and down feature must be activated
again.
.. Pull the power window sw itch until the w indow
is comp letely raised.
... Release the sw itch and pull it agai n for at least
one second.
Panorama roof
Description
App lies to veh icles : with panoramic sunroof
Fig . 3 1 Sect ion of head liner: panorama glass roof butto n
44
The button has two stages . In the second stage,
the roof automatically runs to the end position
(open/closed) when the button is operated brief­
ly. The movement can be stopped by pressing the
button.
@ Tilting and sliding
.. To tilt the sunroof completely, press the switch
briefly to the second level.
.. To close the roof completely, pull the button
down briefly to the second level or s lide the
button forward briefly to the second level
Q &_.
.. To select an intermediate position, press/pu ll
the switch in the first level until the desired po­
sition is reached .
@ Opening and closing
.. To open the sunroof completely, slide the but­
ton back to just befo re the second level.
.. To close the roof complete ly, push the button
forward b riefly to the second leve l or pull the
button down briefly to the second leve l¢ ,& .
.. To sele ct an intermediate posit ion, p ress/pu ll
the switch forward/back in the first level until
the desired position is reached.
A wind def lector integrated in the panorama sun­
roof adapts automatically to the sunroof posi­
tion. Th is reduces wind noise to a minimum in all
panorama s unroof positions.
You can sti ll operate the panorama sunroof for
about 10 minutes after the ignit ion is switched
off. The switch is deactivated once the driver's or
front passenger's door is opened.
Sun blind
The sun shade can be opened and closed manual­
l y, depending on the position of the panorama
sunroof. The sun s hade can be opened partially.
A WARNING
Be caref ul when closing the panoramic sun­
roof - otherwise serious injury could result! Al­
ways take the ignition key with you when leav-
-
ing the veh icle. ti,.

Lights and Vision
Lights and Vision
Exterior lighting
Switching lights on and off
Fig. 32 Instrument pa nel: lig ht sw it c h (ex am ple)
I
The headlights only work when the ignition is
sw itched on . The headlights turn off automati­
cally when the engine is switched on or when the
ignit ion is switched off . Only the side-marker
lights stay on .
A warning symbol w ill appear in the driver infor­
mat ion disp lay if the system is not functioning
correctly ¢page 25.
Light switch ·f!-·
Turn the switch¢ fig. 32 to the corresponding
posi tion . When the ligh ts are sw itched on, the re­
spective symbol turns on .
O -lights off . In som e countr ies, th e day tim e
r unning lights * are turned on and off together
with the ign ition.
- USA mode ls: the daytime running lights switch
on automatically when th e ignition is switched
on and the light switch ¢ fig. 32 is set to the
0
or the AUTO position (only in daylight) . The
Daytime runn ing lights can be switched on and
off in the MMI ¢ page 48 ¢
,&..
-Canad a models : the daytime runni ng lights
switch on automatically when the ignit ion is
switched on and the light switch¢ fig . 32 is in
the
O pos it ion, :oo~ or the AUTO position (only in
daylight)
~ ,&. .
AU TO* -automatic headlights switch o n and off
dependi ng on br igh tness, for example in tw ilight,
du ring ra in or in tunne ls. In veh icles with inte­
g ra ted day time r unning lights*, ei ther the day-
46
time runn ing lights or the headlights will turn on
automatica lly, depending on the amount of light
(may vary depending on the country) .
;oo~ -Par king light
iD -low beam headlig hts
The following w ill happen in these light switch
pos itions when you lock the vehicle:
- io -Low beam headlight: the entire exterior
lighting is switched off
- AU TO* : the Coming home* f unction is turned
on ¢page48
Fog lights* /rear fog light (s )
Press the cor respondi ng b utton ¢fig. 32:
~0 -Front fog ligh ts* (not pictured) . This b utton
r ep laces the b utton for all-weath er lights
"1io.
When the fog lig hts are sw itched on, the }0 sym­
bo l in the b utton ill uminates.
0$ -Rear fog light(s) When the rear fog lights are
swi tched on, the
0$ symbo l in the b utton illumi­
na tes.
All-weather lights*
apples to vehicles with L ED headlights .
Press the correspondi ng button
'wlD ~ fig . 32 on
the light switch :
'?IP -All-wea ther lights. The symbo l "1$D in the
button lights up when all-weather lights are
switched on .
In vehicles with all-wea ther lights , the front
li g ht s are adjusted automatically so that you are
l ess likely to see g lare from your own head lights,
for example when driving on a wet road.
Headlight range control system
The head light range adjusts a utom atically whe n
there is a change in vehicl e load and during brak­
ing and acce lerating so that the headlights do
not cause g la re for oncoming traffic .
Audi adaptive light*
The adaptive light only functions when the ligh t
swi tch is in the AU TO pos it ion. Yo u can de activate
adaptive ligh t in the M MI
~ page 48. .,.

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
When switched on, adaptive light adjusts to
curves depending on the vehicle speed and steer­ing wheel angle. This provides better lighting
through the curve. The system operates in a
speed range from approximately 6 mph (10 km/
h) to 68 mph (110 km/h).
Static cornering light* (vehicles with adaptive
light) -the cornering light switches on automati­
cally when the steering wheel is turned at acer­
tain angle at speeds up to approximately 44 mph
(70 km/h) and when the turn signal is activated
at speeds up to approximately 25 mph (40 km/
h). The area to the side of the vehicle is illuminat­
ed better when turning.
Speed dependent light distribution* -The speed
dependent light distribution adapts the light in
towns and on highways or expressways . Intersec­
tions can also be illuminated on vehicles with a
navigation system* .
Highway light function*
(Vehicles with adaptive light or LED headlights) -
This function adapts the lighting for highway
driving based on vehicle speed .
& WARNING
-Automatic headlights* are only intended to
assist the driver. They do not relieve the
driver of responsibility to check the head­
lights and to turn them on manually accord­
ing to the current light and visibility condi­
tions. For example, fog cannot be detected by the light sensors . So always switch on the
low beam under these weather conditions
and when driving in the dark
io.
-Accidents could occur if you cannot see the
road ahead of you well and if others on the
road cannot see you . Always switch your
headlightsonsothatyoucanseetheroad
ahead of you and others can see your vehicle
from behind.
- The rear fog lights should only be turned on
in accordance with traffic regulations, to
prevent glare for traffic behind your vehicle .
-If the battery has been discharging for a
while, the parking lights may switch off au­
tomatically to conserve the battery charge
Lights and Vision
for the next time the engine is started. Al·
ways make sure your vehicle complies with
legal regulations regarding sufficient and
safe lighting when parking it. Avoid using
the parking lights for several hours.
- Please observe legal regulations when using
the lighting systems described .
@ Tips
-The light sensor for the automatic head­
lights* is in the rearview mirror mount.
Therefore, do not place any stickers in this
area on the windshield.
- Some functions of the exterior lighting can
be adjusted
¢ page 48 .
-If you turn off the ignition while the exterior
lights are on and open the door, you will
hear a warning tone.
- In some market-specific versions, the tail
lights do not turn on when switching on the
daytime running lights .
- In cool or damp weather, the inside of the
headlights, turn signals and tail lights can
fog over due to the temperature difference
between the inside and outside. They will
clear shortly after switching them on. This
does not affect the service life of the light­
ing.
- A message will appear in the instrument
cluster if there is a malfunction in the light
sensor
¢ page 25.
Emergency flasher
Fig. 33 Inst rume nt panel: e merge ncy flasher butto n
The emergency flashers makes other drivers
aware of your vehicle in dangerous situations .
N Cl) M 0
> Cl) (0
47

Lights and Vision
.,. Press the~ button to switch the emergency
flashers on or off.
You can indicate a lane change or a turn whe n the
emergency f lashers are sw itched on by using the
turn signal lever. The emergency flashers stop
temporarily .
The emergency flashers also work when the igni ­
tion is turned off.
(0, Tips
You s hou ld sw itch the emergency flashers on
if:
- You are the last car in a traff ic jam so that
a ll other vehicles appro ach ing from be hind
can see yo u, or if
- You r vehicle has bro ke n down or you are
having an eme rgency, or if
- Y our vehicle is being towed or if you a re
tow ing another vehicle .
Turn signal and high beam lever
The lever operates the turn signals, the high
beams and the headlight fla sher.
F ig. 34 Turn signal and h igh bea m lever
Tu rn signal s¢¢
N
0
.... 9 ::i:
;ii
The turn signals activate when you move the lev­
er into a turn signal position when the ignition is
sw itched on.
(D -Turn signal
@ -Turn signal
The turn signal blinks three times if you tap the
lever (conven ience turn s ignal).
48
High beams and headlight flasher [D
Move the lever to the corresponding position:
@ -high beams on
@-high beams off or headlight flasher
The
II i ndicator light in the instrument cl uster
turns on.
A WARNING
High beams can cause glare for other drivers,
which increases the risk of an accident. For
this reason, only use the high beams or the
headlight flasher when they will not create
gla re for othe r drive rs .
Adjusting the exterior lighting
The settings are adjusted in the MMI.
.,. Select : the I MENU I button > Car > Systems *
control button > Vehicle settings > Exte rior
light ing .
Automatic headlights
Yo u can adjust the following settings in the Au­
tomati c headlights
menu:
Activation time -you can ad ju st if the headlights
swi tch on
Early , Medium or Late acco rd ing to t he
sensi tivity of the light sensor.
Audi adaptive light * -you can sw itch adaptive
li gh t
On an d Off .
Coming home, Leaving home*
The coming home f unction illuminates the area
outside the vehicle when you turn the ignition off
and open the driver 's door . To turn the function
o n, select
Lights when leaving car > On .
The leaving home illum inates the area outside
the ve hicle when you unlock the vehicle . To turn
the function on, se lec t
Lights when unlocking
car > On .
The coming home and leav ing home functions
o nl y operate when it is dark and the light sw itch
i s in the
AUTO pos ition . ..,.

Lights and Vision
Instrument illumination
The brightness of the instrument cluster and the
center console can be adjusted .
Fig. 37 Instrument ill umination
Requirement: the light must be switched on.
~ Press the knob to release it .
~ Turn the knob toward"-" or"+" to reduce or in­
crease the brightness.
~ Press the knob again to return it to its original
position.
(D Tips
The needles and gauges in the instrument cluster illuminate when the headlights are off
and the ignition is switched one. The illumina­
tion reduces automatically and eventually
turns off as brightness outside decreases.
This function reminds the driver to turn the
headlights on at the appropriate time.
Vision
Adjusting the exterior mirrors
Fig. 38 Driver's door: knob for the ex ter ior mirrors (exam­
ple)
Turn the knob to the desired position:
50
0 - All adjustment functions are deactivated.
q;p -adjusting the left/right exterior mirror.
Move the knob in the desired direction.
4#1 -Heating* the mirror glass depending on the
outside temperature.
8 -Folding exterior mirrors*. You can select if
the mirrors fold in automatically when you lock
the vehicle In the
MMI* ~ page 40.
Front passenger's exterior mirror tilt
function*
To help you see the curb when backing into a
parking space, the surface of the mirror tilts
slightly. For this to happen, the knob must be in
the position for the front passenger's outside mirror.
You can adjust the tilted mirror surface by turn­ ing the knob in the desired direction . When you
move out of reverse and into another gear, the
new mirror position is stored and assigned to the
key you are using.
The mirror goes back into its original position
once you drive forward faster than 9 mph (15 km/h) or turn the ignition off.
.&, WARNING
Curved mirror surfaces (convex) enlarge the
field of vision. However, they make objects in the mirror appear smaller and further away.
Your may estimate incorrectly when you use
these mirrors to gauge your distance from the
vehicles behind you when changing lanes -ac­
cident risk!
(D Note
- Applies to vehicles with power folding out­
side mirrors*: if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must use the pow­ er folding function to fold the mirror all the
way out. You will hear a loud noise when the
mirrors are latched back in place. The mirror
housing must not be moved back into place
by hand because this would impair the func­
tion of the mirror mechanism.
-

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
-Applies to vehicles without power folding
outside mirrors : if the mirror housing was
moved by outside forces (such as an impact
when maneuvering), you must
move it back
in p lace by hand.
- If you wash the vehicle in an automatic car
wash, you must fold the exterior m irrors in
to reduce the risk of damage to the mirrors. Never fold power folding exterior m irrors*
by hand . Only fo ld them in and out using
the power controls.
(D Tips
If the power adjustment fails, both mirrors
can be adjusted by hand by pressing on the
edge of the mirror surface.
Dimm ing th e mirrors
Your vehicle is equipped with a manual or auto­
matic* dimming rearview mirror.
F ig . 39 Automatic dimm ing rearv iew mirror•
Manual dimming rear vie w mirror
,..
0 0
> u. a,
~ Pull the lever on the bottom of the mirror back.
Automatic dimming rea rview mirror*
~ Press the b utton @. The indicator light @
tu rns on. The rearview and driver's exterior*
mirrors dim automatically when light shines on
them, for example from headlights on a vehicle
to the rear .
A WARNING 1=
Electrolyte fluid can leak from automatic dim-
ming mirrors if the g lass is broken. Electro­
lyte f luid can irritate skin, eyes and airways .
Lights and Vision
-Repeated or long-term exposure to e lectro­
lyte flu id can lead to irritation of the air­
ways, especially in people with asthma or other respiratory conditions. Take deep
breaths immediately after leav ing the vehi­
cle or, if this is not poss ible, open all of the
doors and windows as wide as possib le.
- If electro lyte fluid enters the eyes, flush
them thoroughly with a large amount of clean water fo r at least 15 minu tes and then
seek med ica l attention.
- If electro lyte fluid comes into contact wi th
the s kin, f lush the affected area with clean
water for at least 15 minutes and then clean
with soap and wate r and seek medical at­
tention. Clean affected clothing and shoes
thorough ly before wearing again .
- If the fluid was swallowed and the person is
conscio us, flush the mo uth wit h water for at
least 15 minutes. Do not induce vomit ing
un less this is recommended by medical pro­
fessionals. Seek medical attention immedi­
ately.
(D Note
If the glass on an automatic dimming mirror
breaks, electro lyte can leak out. This liquid
damages plastic surfaces. C lean this liquid as
quick ly as possible w it h a wet sponge .
@ Tips
-If the light reaching the rearview mirror is
obstructed, the automatic dimming mirror
w ill not function correctly,
- The automatic dimming mirrors do not dim
when the inte rior lighting is turned on or
the reverse gear is selected.
51