2016 AUDI A3 heating

Warm and cold
Adjusting the air vents
Fig . 73 Cockpit: ad just ing the a ir vents
®
F ig . 74 Applies on ly to Cana da: ve nt: ad just ing the a irfl ow
set ting . A) D iffused B) Direct
The fo llow ing settings are possible ¢ fig. 73 :
-CD Air flow amount
- @ Air flow d irection
- ® (Applies only to Canada) airf low setting (dif-
fused or direct)
To adjust t he
air flow amount , tu rn the ridged
outer adjusting ring CD¢
fig. 73 . To stop the air
f low, turn the adjusting ring a ll th e way to the
right.
To adjust the
air flow direction , turn the air vent
grill insert @.
(Applies only to Canada) To adjust the air flow
setting s,
pull or press the middle adj ustment
ring @¢
fig. 73:
- Diffu sed air f low ( indire ct @ ): p ress in the cen­
ter adjusting ring gently ¢
fig. 74 .
-Dire ct air flow (st rong @): pull t he center ad­
ju stmen t ring o ut lightly ¢
fig. 74 .
74
Rear window defogger
The LED in the button turns on when the funct ion
i s sw itched on:
- ~ Manual climate cont rol sys tem ¢
page 71,
fig . 71
-00 Automatic climate control systemc:> page 72,
fig. 72.
If the rear window defogger is activated when
the ignit ion is switched on, the battery manage­
ment determines based on the battery charge if
i t is possible to turn o n. Otherwise, the rear w in­
dow defogge r funct ions w ith the engi ne runni ng
and swit ches off a utomat ica lly af te r approxi ­
mately 1 0 - 20 m inu tes, depending on the out ­
s ide temperature.
To p reve nt the rear window defogger from
swi tching off a utoma tically, press and hold the
~ o r [gfil bu tton fo r more th an two se con ds. Thi s
remains stored u p to a pproximately 15 minutes
after t urn ing off the ignition.
Seat heating
Applies to vehicles: with seat heating
The seat heat ing has three levels. The L ED in the
button ind icates the selected heat level.
Manua l clima te contro l system
c::, page 71 ,
fig . 71
and automatic climate control system
r:> page 72, fig . 72.
... To switch t he seat heating on , press t he Ill but­
ton once.
... To switch to a lower level, p ress the
Ill button
aga in.
... To switch the seat heating
off , press the Ill but-
ton repeated ly until the LED turns off.
The s eat heating switch es automatically from
setting 3 to setting 2 after 10 min utes.
When seat heating should not be switched
on
Do not turn the seat heating on un der the follow­
ing c ircumstances :
- Th e seat is unoccupied .
- Th e seat is covered wi th a se at cove r.
- T he seat is covered with a ch ild s eat .

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
- The seat is damp or wet.
A WARNING
Individua ls with reduced sensitivity to pain or
temperature could develop burns when using
the seat heating function. To reduce the risk
of injury, these individuals should not use
seat heat ing .
(D Note
To avoid damage to the heating elements in
the seats, do not kneel on the seats or place heavy loads on a small area of the seat.
(D Tips
- The setting for the seat heating on the driv­
er's side is ass igned to the key that is in use .
- If the front passenger 's seat heat ing is
turned on, it will not turn on again automat­
ically if more than 10 m inutes have passed
between sw itch ing the ign ition off and
switch ing it on again.
Auxiliary heater
A pp lies to vehicles: with diesel e ng in e
In cool outside temperatures, the electr ic auxi li­
ary heater helps the vehicle interior to wa rm
mo re quickly. The a uxiliary heater swi tches on
and off automatically accord ing to the vehicle
heating settings.
The "auxiliary heater " function can be sw itched
on and off in the MMI. Select: the
I MENU I button
> Car > S ystem s* contro l but ton > AC > Au xilia ry
heat er (fuel ).
Warm and cold
Engine preheater
Applies to vehicles: wi th engine prehea te r
( )
Fig. 75 Left fron t bump er: connecto r socke t@ for th e en ·
gine prehea ter
T he engine preheater s lowly warms the engine
coolant using a heating element when the vehicle
is parked. For this function, the cable provided
must be connected to a 120 Volt socket that is
protected from water and t hat is grounded a nd
equipped with a GFI circu it breaker, for example
in a ga rage. The engine reaches operating tem­
perature much more quickly afte r sta rting when
t h e coolant is preheated . This reduces fuel con­
s u mption and exha ust emissions dur ing the
warm-up phase.
Preheat ing the engine can take up to 3 hours de­
pend ing on the temperature o utside.
Connecting the engine preheat er
- Only use the connector cable provided and a
suitable extension cord, if necessary .
- All cables and connectors that are used must not be damaged
~ li::,. .
-Open the cover(!).
- Plug the connector cable into the socket @.
- If necessary, plug the connector cable into the
extension cord. Only use highly durab le exten­
sion co rds that are class 12 or better and can
be properly grounded to a three-prong wall
socket with a GFI circuit breaker and that are
not longe r than 100 feet (30 meters) .
- Plug the connector cable or extension cord into
a grounded 120 Volt wall socket that is pro­
tected by a GFI circuit breaker and that is pro­
tected against rain and other moisture. Never p lug the engine preheater into a conventiona l .._
75

Driving
If you anticipate what you need to do next and
drive economically, you can easily cut your fuel
consumption by 10-15 percent. This section will
give you some tips on how you can help the envi­ ronment and your pocketbook.
(D Tips
The consumption estimates as published by ENVIRONMENTAL PROTECTION AGENCY
(EPA) and Transport Canada may not corre­
spond to your actual consumption on the
road, which will vary depending upon vehicle
load and speed, road and weather conditions,
trip length, etc.
Drive smoothly and keep a lookout ahead
Vehicles use the most fuel when they are acceler­
ating.
.. Avoid unnecessary accelerating and braking .
Vehicles use the most fuel when they are acceler­
ating. If you anticipate what is going to happen next, you will need to brake less and, thus, accel­
erate less. Let the vehicle coast whenever possi ­
ble -for example when you see that the next traf­
fic light is red.
Avoid full throttle
Driving at moderate speeds saves fuel and im­
proves your mileage.
.. Try and keep well below your car's maximum
speed .
Accelerating gently reduces fuel consumption,
engine wear, and does not disturb the environ­ ment.
Fuel consumption, exhaust emissions and engine
noise increase disproportionately at high speeds.
If you drive at approximately three quarters of
top speed, fuel consumption will be reduced by
one half . Never drive faster than the posted
speed limit and weather conditions permit.
78
· Reducing unnecessary idling
Even when your car is just idling it burns up fuel .
.. Shut the engine off when you are not driving
the vehicle .
.,. Do not warm up the vehicle by letting the en-
gine run at idle .
It is efficient to switch off the engine when stop­
ped at railroad crossings and long red lights.
Turning the engine off for just 30 -40 seconds
saves more fuel than is burned by starting the
engine again .
It takes a long time for the engine to warm up
fully when it is running at idle . However, wear
and noxious emissions are especially high when
the engine is warming up . So you should drive
away as soon as you start the engine and avoid running at high rpms while the engine is still
warming up .
@ Note
Do not leave engine idling unattended after
starting. If warning lights should come on to
indicate improper operation, they would go
unheeded. Extended idling also produces
heat, which could result in overheating or
other damage to the vehicle or other proper­
ty.
Regular maintenance
A badly tuned engine unnecessarily wastes a lot
of fuel.
.. Have your vehicle serviced at regular intervals.
By having your vehicle regularly serviced by an
Audi dealer helps to ensure that it runs properly
and economically. The condition of your vehicle
not only affects its safety and ability to hold its
value, it also affects
fuel consumption.
Check your oil each time you fill your tank.
The amount of oil used is related to engine load
and speed.
It is normal for the oil consumption of a new en­
gine to reach its lowest value after a certain mile -
age has been driven . ..,.

Driving
-Always hold the steering wheel with your
hands in the 9 o'clock and 3 o'clock posi­
t ions to reduce the risk of injury if the airbag
deploys.
- Never hold the steer ing whee l in the
12
o'clock posit ion or with both hands on the
rim or the center of the steer ing whee l.
Holding the steering wheel inco rrectly s ig­
nificantly incr eas es the risk of inju ry to the
h ands, arms and head if t he ai rbag dep loys.
Starting and stopping
the engine (vehicles with
an ignition Lock)
Starting the engine with the key
A pp lies to veh icles: w ith ig ni tion lock
The ignition is switched on and the engine start­
ed with the key in the ignition .
Fig . 77 Ign it io n key pos it ions
Stee ring lock
If the steering whee l w ill not turn, the steering
lock is engaged .
.,. To release the steering wheel lo ck, inse rt the
k ey i n the ignition lock and tu rn t he key in the
-d irection of the arrow- while tu rning the steer­
ing wheel.
Sw itching the ignition on/off or preheating
.,. To switc h the ignition on, turn the ign ition key
to posit io n @ . The need le in the tachometer
moves into the
READY position.
.,. To switc h the ign ition off, turn the ignit ion key
to position @. The need le in the tachometer
moves into the
OFF position.
80
D iesel ve hicl es are p reheated while the ig nition is
switched on
m .
Starting the engine
You r vehicle is equipped wi th la unch control. As
soon as you have turned the ig nition key to pos i­
tion @, the eng ine will start au tomati cally .
.,. Press the brake pedal and move the sele ctor
lever to the P o r
N position.
.,. Turn the key briefly to pos it ion @. The ign ition
key a utomat ically returns to position @. D o not
press the acce lerator peda l when doing this.
Major elec trical equipmen t sw itches off tempora­
r ily whe n starting the engine.
It is possible t hat there will be a s ligh t de lay
whe n starting the engine in diesel veh icles in
colder temperatu res. Therefore, yo u must hold
t h e b rake pedal down until the eng ine starts . T he
i ndicato r ligh t turns on wh ile the engine is pre­
heating
iJ.
The preheating time depends on the coolant
temper ature and o utside temperature. The glow
pl ug indi cato r light
m will only tu rn on for ap­
proximately
1 second when the engine is warm or
t h e outside temperat ure is higher than
8 °C. That
means you can start the engine
immediately.
I f the engine does not s tart immedia tely, s top
the starti ng p rocedure by tu rni ng the ig nition key
to posit ion @ and repeat after
30 seconds .
Automatic start malfunction
There is an a utom atic st art ma lf u nct ion if the ~
(ga so lin e engine) or
m (diese l eng ine) indica tor
li ght tur ns on and the message
Engine start sys·
tem malfun ction! Please contact Service
ap ­
pears.
To star t the engine, hold the igni tion key in pos i­
tion @unt il the engine r uns.
D rive to an au thori zed A udi dealer or au thori zed
A udi Se rvice Fa cility immed iate ly to h ave the
malfunc tion correc ted .
& WARNING
- To red uce the r isk o f po ison ing, never allow
the engine to run in conf ined spaces .

Driving
Otherwise, there is the r isk that the vehicle
could roll.
- After the engine has been switche d off, the
radiator fan can continue to run for up to 10
minutes - even with the ign ition switched
off . It ca n also switch on again after some
t i me if the coolant tern perature rises as the
resul t of heat buildup or if the engine co m­
partment is heat ed by the su n's rays and the
eng ine is ho t.
(D Note
- If t he engine has been unde r heavy load for
an extended pe riod of time, heat builds up
i n the eng ine compartment after the eng in e
i s sw itche d off- the re is a risk of dam ag ing
the engi ne . Fo r thi s reaso n, let the e ng ine
run for at id le for approxim ately two mi ­
nutes befo re sh utting it off .
Starting and stopping
the engine (vehicles with
a convenience key)
Engine with the
button Starting
App lies to vehicles: w ith conve nien ce key
The I START ENGINE STOP I button switches the
igni tion on and s tar ts the engine.
F ig . 78 Cente r conso le : STAR T ENGIN E ST OP butto n (w ith
co nve nience key)
You can start yo ur car w ithout using your conven­
ience key . You must simp ly be c arrying the key
with you .
Plug-in hybrid drive* : refer to the informatio n for
starting the vehicle under ¢
page 100.
82
Switching the ignition on /off or preheating
If thP 'Tij ind icator lig ht blinks and the mess age
Plea se move steerin g wheel appears when
switching the ignition on, the stee ring is locked
by the steer ing lock . In th is case, turn the steer­
i ng wheel slightly to the left/right.
.,. To switch the ignit ion on or off, press t he
I STAR T ENGINE STOPI button . Do not press the
brake pedal while doing this .
The need le in the t achome ter moves to
READY
whe n the ignition switches on an d moves to OFF
when the ignition switches off .
D iesel ve hicles are p rehea te d while the ig nition is
switched on
Iii .
Starting the engine
Your vehicle is equipped with la unch control. The
engine starts a utomat ica lly when you press the
I START E N GIN E STOP ! button br iefly.
.,. Press the brake pedal and move the selector
lever to the P or N position .
.,. Press the
I START E NGINE STOP ! button briefly .
T he engine w ill sta rt.
Major elect rical equipment sw itches off tempora­
rily whe n starting the eng ine .
It is possible that there will be a s light de lay
when starting the engine in d iesel veh icles in
colder temperatures . Therefore, you must hold
the b rake pedal down until the eng ine starts . Th e
i ndica to r light turns on wh ile the engi ne is pre­
hea ting
Iii .
The preheating t ime depends o n the coolant
temperat ure and outside temperature . The glow
pl ug indica to r li ght
II will only tu rn on for ap­
prox im ately 1 se co nd when the engi ne is warm o r
t h e ou ts ide temperat ure is higher th an 8
°C. Tha t
me ans you can s tart t he engine
immedia tely .
If th e engine does not start immediately, stop
th e starti ng p ro cedure by pushi ng the
I S TAR T EN GINE ST OP ! button ag ain an d repe at
a ft er 30 seconds. ..,.

,....,
N
0 > co ,...., Launch Control-Program
Applies to vehicles: with launch control
The Launch Control Program enables maximum
acceleration .
Requirement: the engine must be at operating
temperature and the steering wheel must not be
turned .
.. With the engine running, press the
l~OFF ! but­
ton briefly one time
ll .
.. Pull the selector lever back out of the D/S posi­
tion briefly to select the S position, or press it
toward the right into the tiptronic pos ition or
select the
D ynami c driving mode in drive se­
lect*
~page 148.
.. Press the b rake peda l firmly wi th you r left foot
and hold it all the way down for at least 1 sec­
ond.
.. At the same time, press the gas pedal all the
way down with your right foot until the engine
reaches and stays at a high RPM level.
.. Remove your left foot from the brake.
A WARNING
-Always adapt yo ur driv ing to the traffic flow.
- Only use Launch Control when road and traf-
fic cond itions allow it and other dr ivers will
not be endangered or impacted by you r d riv­
ing and the vehicle's accele ration.
- Please note that the drive whee ls can sp in
and the vehicle can break away when sport
mode is swit ched o n, especia lly when the
road is s lippery.
- Once t he vehicle has sta rted moving, press
the
I $? OFF ! button briefly to t urn the sport
mode off.
(D Tips
- The transmiss ion temperature may increase
s ignificantly after using the lau nch cont rol
program.
If that happe ns, the program m ay
l) In vehicles w ith a d river information system, an ESC light
in the instrument cluster stays o n continuous ly and the
message
Stabili za tion contro l (E SC ): sport . Warning! Re·
stricted st abi lity
appears temporar ily.
Autom atic tran sm iss ion
not be ava ilab le for a few minutes. It will be
avai lab le again after a cool-down period.
- Whe n accelerating using the launch contro l
program, all vehicle parts a re su bject to
heavy loads. This can lead to increased
wear.
Emergency mode
Applies to vehicles: wit h S tronic transmiss ion
In the event of o system mo/function, there is on
emergency program.
If all of the selector lever positions are hig hlight­
ed with a light background in the instrument
cluster disp lay, there is a system malfunction and
the S tronic transmission is running in the emer­
gency program. The vehicle can still be driven in
emergency mode, but only with reduced speed
and not in all gears . In some cases, the vehicle
cannot drive in rever se .
(D Note
If the transm ission runs in emergency mode,
drive to an authorized A udi dealer or author­
iz ed Audi Se rvice Facility immed iate ly to have
the malfunc tion corrected.
Transmission malfunction
• Tran smi ssion malfunction ! Pl ea se stop the
vehicle and select P
The re is a ma lfunction in the transmission. Park
the vehi cle secure ly and do not cont in u e driv ing.
See a n author ized Audi dealer or au thori zed A udi
Service Facility for assis tance.
• Tran smission overheating! Plea se stop the
vehicle!
The transmiss ion is too hot and can become dam­
aged. Stop and let the transmiss ion cool w ith the
engi ne r unning (at idle) in the P se lector lever po­
s it ion. Then the ind icator lig ht and the message .,.
95

Automatic transmission
turn off, drive to an authorized Audi dea ler or au­
thorized Audi Service Facility immediate ly to have
the malfunction corrected . If the ind icator light
and the driver message do not turn off, do not
continue driving. See an authorized Audi dealer
or authorized Audi Service Facility for assistance .
rm Transmission malfunction: you can continue
driving
Drive to an autho rized Audi dea ler or authorized
Audi Service Facility immediately to have the
malfunct ion corrected .
rm Transmission malfunction: no reverse gear
(you can continue driving)
Drive to an authorized Aud i dea ler or authorized
Aud i Service Facility immediately to have the
malfunct ion corrected.
[O] Transmission malfunction: You can continue
driving in D until engine off
Drive the vehicle away from moving traffic and
park. See an authorized Audi dealer or authorized
Audi Service Facility for assistance .
rm Transmission overheating! Please adapt
driving style
Continue driving moderately. When the indicator
light turns off, you can continue driving normal­
ly .
rm Transmission: Press brake pedal and select
gear again.
If the transmission malfunctions because the
temperature is too high, a message appears
when the transmission is cooled.
96
Selector lever emergency release
App lies to vehicles: wit h S tronic transmission
If the vehicle's power supply fails, the selector
lever can be released in an emergency.
Fig. 86 Se lector leve r: remov ing the cover
Fig. 87 Selector lever: us ing the emergency release to
move out of the Pa rk posit ion
The emergency release mechanism is located in
the right area under the selector lever shift gate.
Using the emergency release can be complicated.
We recommend contacting an authorized Audi
dealer or authorized Audi Service Facility for as­
sistance, if necessary .
The screwdr iver from the vehicle tool kit located
i n the luggage compartment is needed to for the
eme rgency release¢
page 280 . Use the flat side
of the reversible screwdriver blade.
Removing the selector lever cover
.,. Set the parking brake(®)¢,& to secure your
vehicle from rolling .
.,. Insert the flat side of the screwdriver s ideways
in the slot near the s hift cover and pry the shift
cover up
¢ fig. 86 .
.,. Pull up the corners of the shift cover carefully
with your hands and fo ld it over the shifter
knob
¢ fig . 87. ..,.

e-tron
overhangs, carports or similar structures . Switch
the ignition
off. Have the problem corrected by
an author ized Audi dealer or authorized A udi
Serv ice Facility .
• Elec tric s ystem: o verheated. Safel y park ve­
hicle and check coo lant
The coolan t leve l is too low or the coolant tem ­
pera ture is too high .
S top the vehicle in the outdoo rs as soon as it is
safe ly possible . Switch the ignition off.
Read the important safety precautions ¢.&.
in
Coolant on page 109 and check the coolant level
¢page 108.
If the coolant level is OK, the malfunction may be
caused by the system overheating . Let the vehi­
cle's electric drive system cool down for some
time .
If the message turns
off after cooling down and
sw itching the ign ition back on, you ca n continue
driving. Contact an author ized Audi dealer or au­
thor ized A udi Se rvice Facility immed iate ly to have
the ma lf u nction co rrected.
If the indicator lig ht stays on, contact an author­
ized A ud i dealer or authorized Aud i Serv ice Faci li­
ty .
Bil Drive system : sys tem fault! Pleas e contact
work shop
There is a malfunction in the plug-in hybrid sys ­
tem. Drive to an authorized Audi dealer or au­
thor ized Audi Service Facility immediate ly to have
the ma lfunction corrected .
II Drive sy stem: system fault! Restart not po s·
sible. Ple ase contact wo rkshop
There is a mal func tion in the plug -in hybrid sys­
tem . Do not open the engine compartment lid .
Drive to an a uth orized Aud i dea le r or authorized
Aud i Serv ice Facility immediately to have the
malfunct io n corrected.
II Batter y temperature too low . Engine start
not possible . See owner's manual
The outside temperature is too low. The vehicle
can no longer start at temperat ures below -18 °F
102
(- 28 °C) . Contact your author ized Audi dealer or
autho rized Audi Service Facility.
POWER LIMIT Warning! Limited power
If the indicator l ight turns on and this message
appears , there may be an engine cont rol mal­
funct ion. The
(m ind icator light in t he instr u­
ment clus ter a lso turns on. The e ng ine o utput is
reduced. Dr ive to an a utho rized Audi dea ler or
autho rized Audi Service Facility immedia tely to
have the malfunction corrected.
II e -tron mode : EV curr ently unavailable
This message appears w hen the 1-,$ 1 button is
pressed and the conditions for e lectric drive
mode are no t me t.
IIJ Vehicle sound: malfunction! Pedestrians
cannot h ear vehicle. P lease contact Service
if the indicator light t urns on and this message
appears, pedestrians and bicyclists can no longer
hear the vehicle when it is driving in electric
mode. Turn off the veh icle and switch to dr iv ing
with the gasoline e ngine . To activate the gasoli ne
engine, select the
Charge batt ery mode
¢page 103 with the kl"I button. Drive to a n au­
tho rized Audi dea le r or a uthorized Audi Service
Facility immediate ly to have the malfunction cor ­
rected.
Range display
Applies to vehicles: wit h pl ug-in hy brid drive
Fig. 89 Ins trument cluster example image: range disp lay
The range can be d isplayed in the on -board com­
p uter ¢
page 29.
Depend ing o n the selected p lug-in hybrid mode,
the d isp lay disp lays the follow ing informa tion:
Ill>