2016 AUDI A3 safety

Emerg ency assis ta nce
Raising the vehicle
The vehicle must be li~ed with the jack first be­
fore the wheel can be removed .
Fig. 216 Sill panels : markin gs (example)
Fig . 217 S ill : pos itio ning the vehicle jack
• Engage the park ing b rake to prevent you r vehi­
cle from rolling unintentionally.
• Move the
sel ec tor lev er to position P.
• Find the ma rk ing ( impr int) on the sill that is
nearest the wheel that will be changed
¢ fig. 216 . Behind the marking, there is a lift­
ing point on the sill for the vehicle jack .
• Vehicles with a sill: Note the posit io n of the s ill
when positioning the vehicle jack ¢
fig. 217 .
• Place the vehicle jack (veh icle tool kit) on a firm
s u rface. Use a flat, stable s upport if necessary.
On a slippery surface such as tile, you should
use a non-slip pad (such as a rubber mat)
¢ .&_ .
• Turn the vehicle j ack located under the lifting
point on the sill to ra ise the jack until its arm @
¢fig . 217 is located under the designated plas­
tic mount ¢
_A, ¢(D.
• Al ign the jack so that its arm @
q fig. 217 en­
gages in the des ignated lift ing po int i n the doo r
s ill and the movable base @ lies flat on the
ground. The base @ must be
vertical under the
li ft ing point @.
286
• Wind the jack up further until the flat tire
comes off the ground ¢
_A.
Position the vehicle jack only under the designat ­
ed lifting points on the sill ¢
fig. 216. There is ex­
actly
one l ocation fo r each wheel. The jack must
not be positioned at any other location ¢
,1.¢(D .
An un stab le surf ace under the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground. If necessary
place a st urdy board or similar s upport under the
jack. On
ha rd, slipper y sur fac es (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping ¢& .
A WARNING
-You or your passengers could be inj ured
while changing a wheel if you do not follow
these safety precautions:
- Position the vehicle jack only at the desig­
nated lifting po ints and align the jack .
Otherwise, the veh icle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle .
- A soft or unstab le surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the gro und . If necessary, use a sturdy
boa rd unde r the jack.
- On hard, slippery surface (such as t iles)
u se a rubber mat o r similar to p revent the
ja ck from s lipp ing.
- Only raise your vehicle with the veh icle
j ack prov ided by the factory . If you use a
vehicle jack for another veh icle, yo ur vehi­
cle can s lide and cause injury.
- Changes in tempe rature or load can affect
the he ight of the vehicle.
- Never start the eng ine when the vehicle is
r aised, w hich could cause an accident.
- Suppo rt the vehicle sec urely with appro­
priate stands if work is to be pe rformed
u ndernea th the ve hicle; ot herwise, there
i s a potent ial risk for in jury.
- To he lp prevent injury to yourse lf and your
p assengers: .,.

.... N
Fuses and bulbs
Electrical fuses
Replacing fuses
A fuse that has blown will have metal strips tha t
have burned through .
Fig. 224 Steer ing colu mn area : cove r
Fig. 225 Left side of the engin e com partment : fus e cover
Fuses in the interior
The fuses are behind the cover in the steering
column area
¢fig. 224.
• Switch the ign ition and all electr ical equipment
off .
• Check the following table to see which fuse be­
longs to the equipment
r::!.> page 292.
• Remove the cover ("AIRBAG" label)
¢ fig. 224.
Begin at the bottom right corner -arrow- .
• Remove the plastic clip from the fuse panel
cover in the engine compartment ¢
fig. 225.
• Remove the fuse using the plastic clamp.
• Replace the burned fuse with an identical new
one .
• Install the cover .
~ Fuses in the engine compartment CX)
rl
~ •Turnoff the ignition and the failed electrical
~ equipment . ....
Fuses and bulbs
• Check the following table to see which fuse be­
longs to the equipment¢
page 293.
• Remove the fuse panel cover r::!.> fig. 225.
• Remove the plastic clip from the fuse panel
cover¢
fig . 225 .
• Remove the fuse using the plastic clamp .
• Replace the burned fuse with an identical new
one .
• Reinstall the cover.
The individual circu its are protected by safety
fuses . The fuses are located under the steering
wheel beh ind a cover and in the left side of the
engine compartment .
Fuse color identification
Color Current rating
in amps
Black 1
Purple 3
Light brown 5
Brown 7.5
Red 10
Blue 15
Yellow 20
White or transparent 25
Green 30
orange 40
A WARNING
Do not repair fuses and never replace a blown
fuse with one that has a higher amp rating .
This can cause damage to the electr ical sys­
tem and a fire.
(D Note
If a new fuse burns out again shortly after you
have installed it, have the electrical system
checked as soon as possible by an authorized
Audi dealer or authorized Audi Service Facili­
ty.
(0 Tips
- Th e following table does not list fuse loca­
tions that are not used.
291

Fuses and bulbs
-Some of the equipment listed in the follow­
ing tables applies only to certain mode l ver­
sions or certain optional equ ipment.
Interior fuse assignment
F ig. 226 Vehicle interior: fuse assignment
No. Equipment
Fl Engine components
F2 Seat adjustment
F3 Hydraulic pump
cover (Cabriolet)
F4 MMI control panel, MMI components
FS Gateway
F6 Selector lever (automatic transmiss
ion)
.... ~ N 0
> a) cc
F7 Climate/heating cont
rol, auxiliary heating,
rear window defogger relay
Diagnosis, electromechanical parking
brake switch, light switch , rain and light
F8 sensor, interior lighting commun ication
box (Plug-in hybrid drive*) ant i-theft alarm
system
F9 Steering column switch module
FlO Display
Fll Reversible driver's side safety belt tension-
ers
Fl2 MMI area
292
No.
Fl3
Fl4
FlS
Fl6
Fl7
Fl8
Fl9
F20
F23
F24
F25
F26
F27
F28
F29 F31
F32
F33
F34
F35
F36
F37
F38
F39
F40
F41
F42
Equipment
Adaptive dampers control module/ service plug (Plug-in hybrid dr ive")
Climate control system blower Electronic steering column lock
MMI area
Instrument cluster
Rearview camera
Convince key system control module, tank
system
Tank system Exterior lighting, heated washer fluid noz-
zles
Panorama sunroof/ power top control
module, power top latch (Cabriolet)
Door/dr iver's side doors (for example pow-
er windows)
Seat heating
Sound-amplifier
Power top control module, electro nics
(Cabriolet)
Interior lights
Exterior lighting
Driver assistance systems
A irbag
Button illumination, coils for upper cabin
heating relay (Cabriolet) and socket relay,
interior sound, reversing light switch, tern-
perature sensor
Function lighting, diagnosis, headlight
range control system, air quality sensor,
automat ic dimming rearv iew mirror
Right corneri ng light/ r ight LED-headlight
Left cornering light/ left LED-headlight
High-voltage battery (Plug- in hybrid
drive*)
Door/front passenger's side doors (for ex-
ample, power windows)
Sockets
Reversib le front passenger's side safety
belt tensioners
Central locking components, windshield
washer system

Fuses a nd bul bs
Bulbs
Replacing light bulbs
For your safety, we recommend that you have
your authorized Audi dealer replace burned out
bulbs for you.
It is becoming increasingly more and more diffi­
cult to replace vehicle light bulbs since in many
cases, other parts of the car must first be re­
moved before you are able to get to the bu lb .
This applies espec ially to the light bulbs in the
front of your car wh ich you can only reach
through the engine compartment .
Sheet metal and bulb holders can have sharp
edges that can cause ser ious cuts, and parts
m ust be correctly taken apa rt and then p roperly
put back together to help prevent breakage of
parts and long term damage from water that can
enter housings that have not been properly re­
sealed.
For your safety, we recommend that you have
your authorized Audi dealer replace any bu lbs for
you, since your dealer has the proper tools, the correct bulbs and the expertise.
G as di sc harg e l am ps (Xe non li ghts):
Due to the high electrical voltage, have the bulbs
replaced by a qua lified technic ian . Headlights
with Xenon light can be identified by the high­
voltage sticker.
LED headlights* require no maintenance. Please
contact your authorized Aud i dealer if a bulb
needs to be replaced.
A WARNING
Contact w ith high-voltage components of the
electrical system and improper rep lacement
of gas discharge (Xenon) headlight bulbs can
cause serious personal injury and death.
- Xenon bulbs are pressurized and can ex­
plode when being changed.
- Changing Xenon lamps requires the special training, instructions and equipment.
- Only an a uthorized Audi dea ler or other
qualified workshop should change the bulbs
in gas discharge lamps .
294
A WARNING
-
There are parts with sharp edges on the open-
ings and on the bulb holders that can cause
serious cuts.
- If you are uncertain about what to do, have
the work performed by an authorized Audi
dealer or other qualified workshop. Ser ious
pe rsonal injury may resu lt from improperly
pe rformed wor k.
@ Tips
- If you still prefer to replace the light bulbs
yourself, be aware that the engine compart­ ment is a hazardous area to work in
9 page 2369 .&.
-It is best to ask your authorized Audi dealer
whenever you need to change a bulb.

,....,
N
0 > co ,...., 9. In the veh icle that is being jump started,
switch the heater fan and rear window de­
froster on to reduce any voltage peaks that
may occur when disconnecting the jumper
cab les. The he adlights must be switched off.
10 . With the engines running, remove the cables
i n
reverse order of the way they were instal­
l ed . Make sure the cables do not get caught
in mov ing engine components.
11. Sw itch the heater fan and rear w indow de-
froster off.
12. Close the battery cover .
The battery is vented to the o utside so that not
gases enter the passenger compartment. Make
sure that the connected positive terminal clamps
on the jump start cab le have sufficient contact
with m etal.
.&_ WARNING
Follow the warnings and instructions from
the jump start cable manufacturer to reduce
the risk of serious injuries and vehicle dam­
age. If you are unsure about anything, call
roads ide assistance.
- The jump start cables must be long enough
so that the veh icles do not touch .
-
-Route the jump start cables so they cannot
get caught in the moving parts in the engine
compartment .
- Always read and follow the warnings before
check ing anything in the engine compart­
me nt ¢
page 236.
Connecting jump start cables incorrectly can
destroy the alternator .
- Always connect the positive terminal(+) to
the positive term inal( +) and the negative
term inal(-) to the negat ive termi nal( -) on
the body ground po int, but not the negative
te rminal on t he battery.
- Make sure the screw plugs on the battery
ce lls are installed securely .
If not, tighten
the p lugs before connecting the clamps to
the negat ive termina l on the battery.
- Please note that the connecting p rocess de­
scribed below for the j ump start cables is in-
Emergency s ituatio ns
tended for when your vehicle is be ing j ump
started.
If you are jump starting another ve­
hicle, do not connect the negat ive cab le to
the negative term inal( -) on the dra ined
battery, but rather connect it to a large
metal component that is bolted secure ly to
the engine block, or to the engi ne b lock it­
self . If the batte ry in the veh icle being jump
s tarted is not ven ted to the outside, there is
a risk of explos ion due to hyd rogen gas .
- Make sure that the connected pos itive ter­
m inal clamps have suff ic ien t conta ct with
metal.
- Do not use the battery negative terminal for
jump starting or a m alfunction co ul d o ccur
in the vehicle e lectrica l system.
Towing with a tow truck
General hints
Your Audi requires special handling for towing.
T he following information is to be used by com ­
mercial tow truck operators who know how to op­
e rate th eir equipment safely.
- Ne ver tow your Audi. Towing will caus e dam­
age to the engine and tr ansmi ssion.
- Neve r wrap th e safety ch ains or win ch c able s
a round the brake lin es.
- To pr event unn ecess ary damag e, your Audi
must be tran sport ed with a flat bed tru ck.
- To load th e ve hicl e on to the flat bed, use the
towin g loop found in the v ehicle tools and at ­
t ac h t o the front o r rea r anchorage
¢ page 298 and ¢ page 298 .
.&_ WARNING ~
A vehicle being towed is not safe for passen-
gers. Never allow anyone to ride in a vehicle
being towed, for any reason.
297

Technical data
Vehicle identification
F ig . 237 Vehi cle Ide ntif icatio n Number (VlN) plate : loca·
t ion on dr iver 's side dash pane l
XXXXX XX -X -XXXX XXX XX
CD+ ~t :1:: xxxxxxxx xx x xxxxxxxx
T VP /fffl XXX XXX
XX XXXXXXX XX X X XX
XXX
K W XXX
®i ~:J ·f lfils~~ XXXX XXX XXX
®-+ ~N:a=i~l xxxx ; xxxx xxx ; xx
II.· AUSS, I OPTIONS
E0A
7D5 4UB 6XM 5SG 5RW
2EH J0Z lLB l
A S lBA
3FC SMU 7Xl
F0A 9G3 0G7 0YH 0JF
TL6 3KA 8EH UlA X98 QZ7
lXW 803 908 824 020
7T6 CV7 7K0 4X3 2K2
3L4
4KC 3Y0 413 502
lSA 7GB 01A 4G0
XX. X XX X XX X xxxx
Fig. 238 Th e ve hicle iden tifica tion label- inside the lug­
gage co mpartment
Veh icle Identification Number (VlN )
The Vehicle Identific ation N umbe r is lo cate d in
d if f eren t places:
- u nder the w indshield on the dr iver's side
c:> fig. 23 7.
- in the M MI: Select: the I MENU I button >Car >
Sy stems *
control b utton > Service & control >
;::: VIN number .
~ -on the vehicle identification label. CX)
rl I.Cl U"I
rl I.Cl rl
Technical data
Vehicle identification label
T he vehicle identi fica tion label is lo cate d in t he
l uggage compa rtment in the sp are whee l we ll.
T he lab el
c:> fig. 238 shows the fo llow ing vehicle
da ta:
(D Vehicle Identification Number (VIN)
@ Vehicle type, eng ine output, transm ission
@ Engine and transmission code
@ Paint numbe r and in terior
® Optional equipment numbers
T he inf ormation of the veh icle identification label
can al so be fo und in your W arranty
& M ainte ­
nance booklet.
Safety compliance sticker
The safety co mpliance sticker is yo ur ass ura nce
t h at your new vehi cle complies w ith all appli cable
Fede ral Motor Vehicle Safety Stand ards which
we re in effe ct at t he tim e the veh icle w as manu ­
fac tured. Yo u ca n fi nd this sticker on the door
jamb on the driver 's side. It shows the month and
year of production and t he ve hicle identification
number of your vehicle (perforation) as well as
t h e Gross Vehicle Weight Rat ing (GVWR) and the
G ross Axle We ight Rati ng (GAWR).
H igh- voltage warning label
T he high-voltage wa rnin g labe l is located in the
engine compartment next to the engine hood re­
lease. The spark ignition system complies with
t h e Canadian standard ICES-002.
Weights
Gross Vehicle Weight Rating
The Gross Vehicle We ight Rating (GVWR), and
t h e Gross Axle Weight Rating (GAWR) for front
and rear a re listed on a sticker on the door jamb
o n the driver 's side .
The Gross Vehicle Weight Rating includes the
weight o f the basic vehicle plus f ull fuel tank, oil
and coolant, p lus maxim um load, which includes
passenger weight (150 lbs/68 kg per des ignated
seat ing pos it ion) and luggage weight
c:> .&, . .,.
301

Consumer information
Consumer information
Warranty coverages
Your Audi is covered by the following warran­
ties:
- New Vehicle Limited Warranty
- Limited Warranty Against Corrosion Perfora-
tion
- Emissions Control System Warranty
- Emissions Performance Warranty
- California Emissions Control Warranty (USA
vehicles only)
- California Emissions Performance Warranty
(USA vehicles only)
Detailed information regarding your warranties
can be found in your
Warranty & Maintenance
booklet .
Operating your vehicle
outside the U.S.A. or
Canada
Government regulati ons in the United States and
Canada require that automobi les meet specific
emission regulations and safety standards.
Therefore, vehicles built for the U.S.A. and Cana ­
da differ from vehicles sold in other countries.
If you plan to take your vehicle outside the conti­
nenta l limits of the United States or Canada,
there is the poss ibility that:
- un leaded fue ls for vehicles with catalytic con­
verter may not be available;
- fuel may have a considerably lower octane rat­
ing . Improper fuel may cause engine damage;
- service may be inadequate due to lack of proper
service facilities, tools or testing equipment;
- r eplacement parts may not be readily available.
- Nav igation systems for veh icles built for the
U.S .A . and Canada will not necessarily work in
Europe, and may not work in other countries
outside North America.
306
(D Note
Audi cannot be responsib le for mechanical
damage that could result from inadequate
fuel, service or parts ava ilability.
Audi Service Repair
Manuals and Literature
Audi Official Factory Service Manuals and Litera ­
ture are published as soon as poss ible after mod­
el introduction . Service manuals and literature
are available to order from the Audi Technical Lit ­
erature Ordering Center at :
www.audi.techliterature .com
Maintenance
General '
Your vehicle has been designed to help keep
maintenance requirements to a minimum. How­
ever, a certain amount of regular maintenance is
still necessary to assure your vehicle's safety,
economy and reliability . For detailed vehicle
maintenance consult your Warranty & Mainte­
nance booklet .
Under difficult operating conditions, for exam ­
ple at extremely low outside temperatures, in
very dusty regions, when towing a trailer very fre­
quently, etc., some service work should be per­
formed between the intervals specified. This ap­
plies particularly to:
- oil changes, and
- cleaning or replac ing the a ir filter .
'
@) For the sake of the environment
By regularly maintain ing your vehicle, you
help make sure that em iss ion standards are
maintained, thus minimizing adverse effects
on the environment .
Important considerations for you and your
vehicle
The increasing use of electronics, sophisticated
fuel injection and emission control systems, and
the generally increas ing technica l complexity of ..,_

today's automobiles, have steadily reduced the
scope of maintenance and repairs which can be
carried out by vehicle owners.
Also, safety and
environmental
concerns place very strict limits
on the n ature of repairs and adjustments to en­
gine and transmission parts which an owner can perform .
Maintenance, adjustments and repairs usually re­
quire special tools, testing devices and o ther
equipment available to specially trained work ­
shop personnel in order to assure proper per­
formance, reliability and safety of the vehicle and
its many systems.
Improper maintenance, adjustments and repairs
can impair the operation and reliability of your
vehicle and even void your vehicle warranty .
Therefore, proof of servicing in accordance with
the maintenance schedule may be a condition for upholding a possible warranty claim made within
the warranty period.
Above all , operational safety can be adversely af­
fected, creating unnecessary risks for you and
your passengers.
If in doubt about any servicing, have it done by
your authorized Audi dealer or any other properly equipped and qualified workshop. We strongly urge you to give your authorized Audi dealer the
opportunity to perform all scheduled mainte­ nanc e and necessary repairs. Your dealer has the
facilities, original parts and trained specialists to keep your vehicle running properly .
Performing limited maintenance yourself
The following pages describe a limited number of
procedures which can be performed on your vehi­
cle with ordinary tools, should the need arise and
trained personnel be unavailable. Before per­
forming any of these procedures, always thor­
oughly read all of the applicable text and careful­ ly follow the instructions given . Always rigorously
observe the
WARNINGS provided .
Before you check anything in the engine com-
,.., partment, always read and heed all WARNINGS
N
~ c::> .&. and c::> page 236.
co ,...., Consumer information
A WARNING
-Serious personal injury may occur as a result
of improperly performed maintenance, ad ­
justments or repairs .
- Always be extremely careful when working
on the vehicle. Always follow commonly ac ­
cepted safety practices and general com­ mon sense. Never risk personal injury.
- Do not attempt any of the maintenance,
checks or repairs described on the following pages if you are not fully familiar with these
or other procedures with respect to the ve­ hicle, or are uncertain how to proceed.
- Do not do any work without the proper tools
and equipment. Have the necessary work
done by your authorized Audi dealer or an­
other properly equipped and qualified work­
shop.
- The engine compartment of any motor vehi­ cle is a potentially hazardous area. Never
reach into the area around or touch the radi­
ator fan.
It is temperature controlled and
can switch on suddenly - even when the en­
gine is off . The radiator fan switches on au ­
tomatically when the coolant reaches a cer­
tain temperature and will continue to run
until the coolant temperature drops.
- Always switch off the ignition before anyone
gets under the vehicle .
-Always support your vehicle with safety
stands if it is necessary to work underneath
the vehicle . The jack supplied with the vehi­
cle is not adequate for this purpose and
could collapse causing serious personal in­
jury.
- If you must work underneath the vehicle
with the wheels on the ground, always make
sure the vehicle is on level ground, that the
wheels are always securely blocked and that
the engine cannot be started.
- Always make sure the transmission selector
lever (automatic transmission) is in P (Park
position) and the park brake is applied .
II>
307