2016 AUDI A3 wheel

Emerg ency assis ta nce
Raising the vehicle
The vehicle must be li~ed with the jack first be­
fore the wheel can be removed .
Fig. 216 Sill panels : markin gs (example)
Fig . 217 S ill : pos itio ning the vehicle jack
• Engage the park ing b rake to prevent you r vehi­
cle from rolling unintentionally.
• Move the
sel ec tor lev er to position P.
• Find the ma rk ing ( impr int) on the sill that is
nearest the wheel that will be changed
¢ fig. 216 . Behind the marking, there is a lift­
ing point on the sill for the vehicle jack .
• Vehicles with a sill: Note the posit io n of the s ill
when positioning the vehicle jack ¢
fig. 217 .
• Place the vehicle jack (veh icle tool kit) on a firm
s u rface. Use a flat, stable s upport if necessary.
On a slippery surface such as tile, you should
use a non-slip pad (such as a rubber mat)
¢ .&_ .
• Turn the vehicle j ack located under the lifting
point on the sill to ra ise the jack until its arm @
¢fig . 217 is located under the designated plas­
tic mount ¢
_A, ¢(D.
• Al ign the jack so that its arm @
q fig. 217 en­
gages in the des ignated lift ing po int i n the doo r
s ill and the movable base @ lies flat on the
ground. The base @ must be
vertical under the
li ft ing point @.
286
• Wind the jack up further until the flat tire
comes off the ground ¢
_A.
Position the vehicle jack only under the designat ­
ed lifting points on the sill ¢
fig. 216. There is ex­
actly
one l ocation fo r each wheel. The jack must
not be positioned at any other location ¢
,1.¢(D .
An un stab le surf ace under the jack can cause the
vehicle to slip off the jack. Always provide a firm
base for the jack on the ground. If necessary
place a st urdy board or similar s upport under the
jack. On
ha rd, slipper y sur fac es (such as tiles)
use a rubber mat or similar to prevent the jack
from slipping ¢& .
A WARNING
-You or your passengers could be inj ured
while changing a wheel if you do not follow
these safety precautions:
- Position the vehicle jack only at the desig­
nated lifting po ints and align the jack .
Otherwise, the veh icle jack could slip and
cause an injury if it does not have suffi­
cient hold on the vehicle .
- A soft or unstab le surface under the jack
may cause the vehicle to slip off the jack.
Always provide a firm base for the jack on
the gro und . If necessary, use a sturdy
boa rd unde r the jack.
- On hard, slippery surface (such as t iles)
u se a rubber mat o r similar to p revent the
ja ck from s lipp ing.
- Only raise your vehicle with the veh icle
j ack prov ided by the factory . If you use a
vehicle jack for another veh icle, yo ur vehi­
cle can s lide and cause injury.
- Changes in tempe rature or load can affect
the he ight of the vehicle.
- Never start the eng ine when the vehicle is
r aised, w hich could cause an accident.
- Suppo rt the vehicle sec urely with appro­
priate stands if work is to be pe rformed
u ndernea th the ve hicle; ot herwise, there
i s a potent ial risk for in jury.
- To he lp prevent injury to yourse lf and your
p assengers: .,.

.... N
0 > CX)
.... I.Cl U"I ,....,
I.Cl ....
-Do not raise the vehicle until you are sure
the jack is securely engaged.
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
p lace away from the vehicle and well away
from the road and traff ic.
- Make sure jack position is correct, adjust
as necessary and then cont inue to raise
the jack.
- Changes in temperature or load can affect
the height of the vehicle.
CD Note
Do not lift the vehicle by the sill. Position the
veh icle jack on ly at the designated lifting
points on the sil l. Otherwise, your vehicle will
be damaged.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig. 2 18 Ch anging a whee l: using the screwd river handle
(with the blade removed) to turn the bolts
F ig . 2 19 Ch ang ing a whee l: alig nmen t pin inside the top
hole
Em ergen cy a ssis tanc e
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and re­
place the wheel as follows:
Removing the wheel
.,.. Use the hexagonal socket in the screwdri ver
handle
to comp letely remove the topmost
wheel bo lt and set it aside on a
clean su rface
c!>fig. 218.
.,.. Screw the threaded end of the alig nment pin
from the tool kit hand-tight into the empty bo lt
hole
r::!> fig . 219.
.,.. Then remove the other wheel bolts as descr ibed
above .
.,.. Take off the wheel leaving the alignment p in in
the bolt hole
~ 0-
Putting on the comp act spare wheel
.,.. Lift the spare wheel and carefully slide it over
the alignment p in to guide it in place
r::!> (0 .
.,.. Use the hexagonal socket in the screwdr iver
handle to screw in and tighten a ll wheel bolts
slightly .
.,.. Remove the alignment pin and insert and t igh t­
en the remaining wheel bo lt s light ly like the
rest .
.,.. Turn the jack hand le counter -clockwise to lower
the vehicle until the jack is fully released .
.,.. Use the wheel bolt wrench to tighten a ll wheel
bolts firmly
r::!> page 285 . Tighten them cross­
wise,
from one bo lt to the (approx imately) op­
posite one, to keep the wheel centered .
CD Note
When removing or installing the wheel, the
rim co uld h it the brake rotor and damage the
r otor. Work carefully and have a second per­
son help you.
0) Tips
Never use the hexagonal socket in the handle
of the sc rewdrive r to loosen or t ighten the
whee l bolts.
- Pull the reversible blade from the screwdr iv­
er before yo u use the hexagona l soc ket in
t he handle to tu rn the whee l bolts.
287

Emergency assistance
- W hen mounting tires w ith unidirectional
tread design
make s ure the t read pattern is
po inted the r ight way ¢
page 288 .
-The wheel bolts should be clean and easy to
turn . C heck for di rt and cor ros ion on t he
mating surfaces o f both the wheel and the
h ub. Remove all dirt from these surfaces be­
fo re remo unting the wheel.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction.
Using a spare tire with a tread pattern
intended for use in a specific direction
When us ing a spare tire with a tread pattern in­
tended for use in a spec ific d irection, p lease note
the following:
- The direct ion o f rotat ion is marked by an a rrow
o n the side of the tire.
- If the spare tire has to be installed in the incor­
rect d irection, use the spare tire only tempora­
rily s ince the tire w ill not be ab le to achieve its
o ptimum performance charac ter istics wi th re­
gar d to a quaplaning, noise and wea r.
- We recommend t hat you pay particular atten­
tion to this fac t during wet weathe r and t hat
yo u ad just yo ur speed to match road condi­
tio ns.
- Replace the f lat t ire with a new one and have i t
i ns ta lled on yo ur ve hicl e as soon as possibl e to
r esto re th e han dling adv antages of a unidi re c­
tio nal ti re.
Notes on wheel changing
Plea se read the info rmation ¢ page 2 60 if you
are go ing to use a spare tire which is different
from the tires on your vehicle.
Af te r yo u change a tir e:
- Check the tire pressure on the spare immedi­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos -
288
sible by your authorized Audi dealer or a
qualified service station.
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm ).
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
t ightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi ­
ble. Remount the wheel cover .
Until then , drive with extra care and at reduced
speeds.
& WARNING
- If you are going to equip yo ur vehicle with
tires or r ims which diffe r from those which
were facto ry insta lled, then be sure to read
t he informa tion ¢
page 260.
-Always make sure the damaged wheel or
eve n a flat tire and the jack and tool kit are
pro per ly secur ed in the l uggage compart­
men t and a re not loose in the passeng er
co mpart me nt.
- In an accident or sudde n maneuver they
co uld fly forw ard, injuri ng anyo ne in the v e­
hicle .
- Always s to re damaged wh eel, jack and tools
s ecure ly i n t he luggage co m pa rt m ent. Oth­
erwi se, in an a ccid ent or sudde n m aneu ve r
t hey cou ld fly forw ard , cau sing injury to pa s­
s engers in the veh icle.
-

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Spare tire
General information
Applies to vehicles: with space-saving spare tire (compact
spare tire)
F ig. 220 Luggage co mpa rtmen t: ca rgo floo r fo lded up (A3
Sportback top, A3 sedan bo ttom )
F ig. 221 Compac t spare tir e
The spare tire ¢ fig. 221 is intended for sho rt­
term use only . Have the damaged tire checked
and replaced if necessary by an authorized Aud i
dealer or authori zed Audi Service Facility as soon
as possible .
There are some restrictions on the use of the compact spare tire . The compact spare tire has
been designed specif ica lly for your type of vehi­
cle . Do not replace it with the spare tire from an­
other type of vehicle.
Em ergen cy a ssis tanc e
Removing the sp are tire (A3 Sportback )
.,. Lift up the cargo floor wi th the p lastic handle
until it is clamped beh ind the tabs on both s ide
pane ls
(D ¢ fig. 220.
.,. Remove the subwoofer* if necessary . Check
which subwoofer is installed based on the con ­
nector : version 1 ¢
page 290 or version 2
¢page 290.
"'Turn the large screw counter -clockw ise .
.,. Remove the spare tire .
Removin g the sp are tire (A3 Sedan )
.,. Lift the cargo floor by the plastic handle.
"' Hang the p lastic hook on the luggage compart-
ment weather strip -arrow -¢
fig . 220 .
"'Turn the large screw counter-clockw ise .
"' Remove the spare tire .
Snow chains
For technical reasons, the use of snow chains on
the compact spare tire is not permitted.
If you have to drive with snow chains and a front
tire fails, mount the spare wheel in p lace of a
rear tire . Install the snow chains on the rear tire
that you removed , and install that in place of the
front t ire that fai led .
A WARNING
=
-After installing a spare tire, the t ire pres-
sure must be checked as soon as possible .
The t ire pressure is availab le on ¢
page 263,
fig. 205.
- If the spa re ti re is mo re t han 6 years old,
use it only in an emergency and with ex­
treme ca ution and careful driving.
- The spare tire is intended only fo r tempora­
ry a nd short-term use.
It should be replaced
as soon as poss ible with the normal whee l
and tire .
- After moun ting the compact spare tire, the
tire pressure must be checked as soon as possible. The tire press ure of the compact
spare tire must be 61 ps i (420 kPA); other­
wise, you risk having an accident .
- Do not drive faster than 50 mph (80 km/h).
You risk having an acc ident. ""
289

Emergency assistance
-Avoid full-throttle acceleration, heavy brak­
ing, and fast cornering. You risk having an
accident.
- Never dr ive using more than one spare
wheel and tire. You risk having an accident.
- Normal summer or winter tires must not be
mounted on the compact spare wheel rim.
- For technical reasons, the use of tire chains
on the spare tire is not permitted. If it is
necessary to drive with tire chains, the spare
wheel must be mounted on the front axle in
the event of a flat in a rear tire. The newly
available front wheel must then be installed
in place of the rear wheel with the flat tire.
Installing the tire chain before mounting
the wheel and tire is recommended.
- Loose items in the passenger compartment
can cause serious personal injury during
hard braking or in an acciden t. Never store
the inflatable spa re tire or jack and tools in
the passenger compartment.
- Normal summer or winter tires must not be
mounted on the compact spare wheel rim .
Removing the subwoofer (version 1)
Applies to veh icles: w ith subwoofer
The subwoofer must be removed before the
spare wheel" can be removed.
F ig. 222 Spare wheel well : subwoofer
Removing the subwoofer
.,. Lift up the cargo floor~ page 289, fig. 220 .
.,. Press the connector tabs CD cc> fig . 222 togeth­
er .
.,. Remove the connector @and set the discon­
nected cable aside .
.,. Remove the bolt @ .
290
.,. Carefully remove the su bwoofer.
Installing the subwoofer
.,. Carefully p lace the su bwoofer in the rim well .
The word "FRONT " on the subwoofer must face
forward.
.,. Insert the connecto r that was removed.
.,. Secure the subwoofer with the bolt.
.,. Fold the cargo f loor cover back into place.
Removing the subwoofer (version 2)
Applies to vehicles: wit h subwoo fe r
The subwoofer must be removed before the
spare wheel" can be removed.
Fig. 223 Spa re w hee l we ll: s ubwoofe r
Removing the subwoofer
.,. Lift up the cargo floor ¢page 289, fig. 220.
.,. Pull the lock CD~ fig. 223 toward the cable .
.,. Press the locking tab @down .
.,. Remove the connector @ and set the removed
cable aside .
.,. Remove the bolt@ .
.,. Carefully remove the subwoofer.
Installing the subwoofer
.,. Carefully place the subwoofer in the r im well .
The word "FRONT" on the s ubwoofer must face
forward.
.,. Insert the connector that was removed.
.,. Secure the subwoofer with the bolt .
.,. Fold the cargo floor cover back into place .

.... N
Fuses and bulbs
Electrical fuses
Replacing fuses
A fuse that has blown will have metal strips tha t
have burned through .
Fig. 224 Steer ing colu mn area : cove r
Fig. 225 Left side of the engin e com partment : fus e cover
Fuses in the interior
The fuses are behind the cover in the steering
column area
¢fig. 224.
• Switch the ign ition and all electr ical equipment
off .
• Check the following table to see which fuse be­
longs to the equipment
r::!.> page 292.
• Remove the cover ("AIRBAG" label)
¢ fig. 224.
Begin at the bottom right corner -arrow- .
• Remove the plastic clip from the fuse panel
cover in the engine compartment ¢
fig. 225.
• Remove the fuse using the plastic clamp.
• Replace the burned fuse with an identical new
one .
• Install the cover .
~ Fuses in the engine compartment CX)
rl
~ •Turnoff the ignition and the failed electrical
~ equipment . ....
Fuses and bulbs
• Check the following table to see which fuse be­
longs to the equipment¢
page 293.
• Remove the fuse panel cover r::!.> fig. 225.
• Remove the plastic clip from the fuse panel
cover¢
fig . 225 .
• Remove the fuse using the plastic clamp .
• Replace the burned fuse with an identical new
one .
• Reinstall the cover.
The individual circu its are protected by safety
fuses . The fuses are located under the steering
wheel beh ind a cover and in the left side of the
engine compartment .
Fuse color identification
Color Current rating
in amps
Black 1
Purple 3
Light brown 5
Brown 7.5
Red 10
Blue 15
Yellow 20
White or transparent 25
Green 30
orange 40
A WARNING
Do not repair fuses and never replace a blown
fuse with one that has a higher amp rating .
This can cause damage to the electr ical sys­
tem and a fire.
(D Note
If a new fuse burns out again shortly after you
have installed it, have the electrical system
checked as soon as possible by an authorized
Audi dealer or authorized Audi Service Facili­
ty.
(0 Tips
- Th e following table does not list fuse loca­
tions that are not used.
291

Emergency situations
Front towing loop
Fig. 230 Right front bumper: removing the cover
Fig. 231 Right front bumper: towing loop installed
The threaded open ing for the tow ing loop is lo­
cated behind a cover on the right side of the front
bumper .
.,. Remove the towing loop from the vehicle tool
k it ¢
page 280 .
.,. Press inward on the upper left area of the cap
with brief, strong pressure to
remove it from
the bumper
¢fig. 230 .
.,. Tighten the towing loop in the threaded open­
ing until it stops
¢fig. 231 and then tighten it
with a wheel wrench.
.,. After using, place the towing loop back in the
vehicle tool kit.
& WARNING
If the towing loop is not installed securely, it
cou ld loosen from the threads w hile towing
and cause damage to the vehicle or injury to
people.
298
Rear towing loop
Fig. 232 R ig ht rear towing loop : cover
Fig. 233 Right rear towing loop: towing loop ins talled
The towing loop threaded opening is located in
the right of the rear bumper cover under a cover .
.,. Remove the towing loop from the vehicle tool
kit¢
page 280 .
.,. To remove the cap from the bumper, press in
on the
upper area of the cap -arrow-with brief,
strong pressure and lift it up from the
lower
area ¢fig. 232.
.,. Tighten the towing loop in the threaded open­
ing until it stops ¢
fig. 233 and then tighten it
with a wheel wrench.
.,. After using, p lace the tow ing loop back in the
vehicle tool k it.
Depending on the model , the shape of the cove r
can vary.
~ WARNING
If the tow ing loop is not installed securely, it
could loosen from the threads while towing
and cause damage to the vehicle or injury to people.

,....,
N
0 > co ,...., Width (across mirrors) He ight (un loaded)al
a) The height of the vehicle depends on the tire s and s uspe nsion .
1)
Capacities
Fuel tank
Front wheel drive/ e -tron
all wheel drive
Windshield washer system
Windsh ield and headlight washer system* i
n (mm)
i n (mm)
gallons (liters)
gallons (liters)
quarts (liters)
quarts (l iters)
Windshield and headlight washer system* (5 modlels) quarts (liters)
Techn ical data
77.3 (1966)1
)
56.1 (1426)1
)
approx . 13.2 (50.0) /
10 .5 (40.0)
app roximately 14.5
(55.0)
approximately 3.2 (3.1)
approximate ly 4. 7 (4. 7)
approximately 4.2 (4.0)
303