2016 AUDI A3 lock

Care and cleaning
Component Situation Solution
Paint
Paint damage Refer to the paint number on the vehicle data label, repair
with touch up paint¢
page 301
Spilled fuel Rinse with water immediately
Surface rust Rust remover, then protect with hard wax; for questions,
consult an authorized Audi dealer or authorized Audi Serv-
ice Facility.
Corrosion Have
it removed by an authorized Audi dea ler or a uthor-
ized A udi Service Facility.
Water no longer Protect with hard wax (at least twice per year)
beads on the surface
of clean paint
No shine even though Treat with suitable polish; then apply paint protectant if
paint has been pro- the polish that was used does not contain any protectant
tected/paint looks
poor
Deposits such as in- Dampen w ith water immediately and remove with a micro-
sects, bird dropp ings, f iber cloth
tree sap and road salt
Grease-based con- Remove immediately wi th a mild soap solution al and a
taminants such as
soft cloth
cosmetics or sunblock
Carbon parts Deposits clean the same way as painted parts¢ page 2 74
Decorative decals Deposits Soft sponge with a mild soap solutional
Audi e-tron Deposits Dry towe l
charging system *
Charging dock*
Deposits Soft towel with alcoho l-free cleaning so lution
a} Mild soa p sol ution: maxim um two tablespoons of neutral soap in 1 quart (I liter) of water
Internal cleaning
Component Situation Solution
Windows
Deposits Glass cleaner, then wipe dry
Decorative parts/ Deposits Mild soap solutional
Trim
Plastic parts
Deposits Damp cloth
Heavier deposits Mild soap so lution al, detergent-free p lastic clean ing solu-
tion, if necessary
Displays Deposits Soft cloth with LCD cleaner
Controls Deposits Soft brush, then a soft cloth with a mild soap solutional
Safety belts Deposi ts Mild soap solution al, allow to dry before letting them re-
tract
276

Emerg ency assis ta nce
Emergency assistance
Trunk escape latch
Applies to veh icles: with trunk escape latch
In case of an emergency, the rear lid can be
opened from the inside using the trunk escape
latch.
Fig. 207 luggage compartment: Trunk escape latch
.,. Push the latch in the direction of the arrow un­
ti l the lock releases.
The trunk escape latch inside the rear lid is made
of fluo rescent mater ial to g low in the dark.
_& WARNING
The trunk escape latch is to be used only in an
emergency .
General information
.,. Park the vehicle as far as poss ible from moving
t raff ic in the event of a flat tire. In the event of
a f lat t ire, park the vehicle on a level surface. It
you are on a steep incline, be especia lly careful.
.,. Set the parking brake.
.,. Place the selector lever in the P pos ition .
.,. Switch the emergency flashers on.
.,. Put on a reflective vest, if available .
.,. Set up the warn ing triangle, if available .
.,. Have the passengers exit the vehicle. They
should move to a safe place, for example be­
hind a guard rail.
_& WARNING
Pay attention to the steps above. They a re for
your protection and the for the safety of other
drivers.
280
Equipment
Vehicle tool kit
Applies to vehicles: with vehicle tool kit
Fig. 208 luggage compartment (example): vehicle tool kit,
t ire mobility kit and vehicle jack* placement
Fig. 209 luggage compartment: cargo floor fo lded up (A3
Spo rtback top, A3 sedan bottom)
Plug-in hybrid drive*: the placement var ies
<>page 107 .
The vehicle tool kit, tire mobility kit* and the
compressor* are located in the luggage compart­
ment. Part of it is sto red in the s ide tr im pan­
el @ * or @ and another part is under the cargo
floor cover ©¢
fig. 208.
C argo floor cove r
.,. A3 Sportback: lift up the cargo floor with the
plastic handle © until it is clamped behind

.... N
0 > CX)
.... I.Cl U"I
.... I.Cl ....
both tabs on the side panels ¢ fig. 209 (top im ­
age).
.. A3 Sedan: clip the plastic hook@ into the lug ­
gage compartment seal¢
fig. 209 (bottom im­
age) .
Side panel
.. Open the twist lock and remove the cover @* I
@ ¢fig. 208 .
.&_ WARNING
Improper use of the vehicle jack can cause se­
rious personal injuries.
- Never use the screw driver hex head to
tighten wheel bolts, since the bolts cannot
atta in the necessary tightening torque if you
use the hex head, potentially caus ing an ac­
c ident.
- The factory-supplied jack is intended only
for your vehicle model. Under no circum­
stances should it be used to
lift heavy
vehicles o r other loads; you r is k inju ring
yo urself.
- Never start the engine when the vehicle is
ra ised, whi ch could cause an accide nt.
- Support the veh icle secure ly with app ropr i­
ate stands if wor k is to be perfo rmed under­
neath t he vehicle; otherwise, the re is a po­
tent ial risk for in jury.
- Never use the jack s upplied with your Audi
on another vehicle, par tic ularly on a heav ier
one. The jack is only suitab le for use on the
vehicle it came with .
(D Tips
The vehicle jack* in your vehicle is mainte­
na nee-free.
Tire mobility kit
Preparation
A ppl ies to vehicles: W ith t ire re pair set
.. Read and fo llow th e import ant saf ety pr ecau­
tion s¢
page 280, General information .
.. Check if a repair w ith the t ire mobility k it is pos­
s ible
¢ page 281.
Emergen cy a ssis tanc e
Using the tire mobility kit
App lies to vehic les : With tire r epair set
F ig. 210 T ire: t ire damage t hat cannot be repaired
The tire repair is only meant for temporary use.
Change the spare tire as soon as possible <=>,&. .
If the t ire is p ierced by an object such as a nail,
do not remove the object from the tire.
The tire repair set is ab le to be used at tempera­
tures as low as - 4 °F (- 20 °C).
The t ire mobility kit may not be us ed:
- if the ti re has cuts or punctures that are larger
than
0 .1 6 in (4 mm)@ ¢ fig. 210.
-if the rim is damaged @.
- if you drove with very low t ire pressure or with-
out air in the tire @.
See an authorized Audi dealer or authorized Audi
Service Facility for assistance in these situations .
.&_ WARNING
>=
-Please note that the tire mobility kit cannot
be used in all situations, and that it may on­
ly be used temporarily.
- The tire sealant must not come in contact
wit h skin, eyes, o r clothes.
- If ti re sealant gets in you r eyes or on yo ur
skin, tho ro ughly rinse the affected area im­
mediately wi th clea n wate r.
- Do not inha le the fumes.
- If you swallow any of the tire sealant, thor-
ough ly rinse your mouth immediately and
drink a lot of water . Do not ind uce vomiting.
Seek med ica l attent io n immed iate ly .
- Change yo ur clothes immediately if they get
tire seala nt on them.
~
281

,....,
N
0 > co ,...., Completing
Appl ies to vehicles: W ith t ire repa ir set
.,. Adhe re the sticke r that says "max. SO mph
(max. 80 km/h)" that is p rovided w ith the t ire
mobility k it within the driver's fie ld of vision .
.,. Stop the vehicle after driving for about 10 mi ­
nutes and check the tire pressure .
.,. lfthe tire pressure is lower than 19 psi (130
kPA), then the tire is too severely damaged. Do
not cont inue driving. See an authorized Audi
dealer or authorized Audi Service Facil ity for as­
s istance .
.,. If the t ire pressure is at least 19 psi (130 kPA),
adjus t the tire pressu re to the spec ified value
~ page 263, Tire pressure . Store the tire pres ­
sures
~page 273, Storing tire pressures . Drive
to the nearest authorized Audi dealer or au­
thorized Audi Serv ice Facility to have the tire re­
placed.
A WARNING
If the tire pressure is less than 19 psi
(130 kPA) after 10 minutes of d riving, then
the tire is too severely damaged. Do not con­
tinue dr iv ing . See an authorized Audi dealer
or autho rized Audi Service Fac ility for assis­
t ance.
A WARNING
Pay a ttent ion to the following after repair ing
the tire:
- Do not drive faster than 50 mph (80 km/h).
- Avoid hard acceleration, brak ing sharp ly,
and fast corner ing.
- The veh icle may become mo re difficu lt to
co ntro l.
-If the t ire is too severely damaged, see an
authorized Audi dealer o r autho rized Aud i
Service Facility for assistance .
@ For the sake of the environment
You can give the used t ire sealant bottle to an
author ized Audi dealer or authorized A udi
Serv ice Facility fo r disposal.
Em ergenc y ass is tanc e
{!) Tips
Remember to obtain a new bott le of sealant
from an authorized A udi dealer or authorized
Audi Service Fac ility after repairing a tire.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a wheel.
.,. After you experience a t ire failure, pull the car
well away from moving traffic and try to reach
le vel grou nd before you stop~,& .
.,. All passengers should
leave the car and move
t o a safe location (for ins tance, behind the
gua rdrail) ~,& .
.,. Engage the
pa rking brake to prevent your vehi ­
cle from rolling unintentionally ~ .,& .
.,. Move
sele ctor le ver to po sition P ~ .,& .
.,. If you are tow ing a trai ler, unhitch the trailer
from yo ur vehicle .
.,. Take the jack Q page 280 and the spare tire
~ page 289 out of the luggage compartment.
A WARNING
You o r you r passengers could be injured while
changing a whee l if yo u do not follow these
safety precaut ions :
- If you have a fla t tire, move a safe dis tance
off the road. Turn off the eng ine, turn the
emergency f lashers on and use other warn ­
ing devices to alert other motorists.
- Make sure that passenge rs wai t in a safe
p lace away from the vehicle and well away
from the road and t raffic.
- To help prevent the vehicle from moving suddenly and possib ly slipping off the jack,
always fu lly set the park ing brake and block
the wheel d iagonally opposite the wheel be­
ing changed . When one front whee l is lifted
off the ground, placing the Automatic
Transmission i n P (Park) w ill
not prevent the
veh icle from moving.
~
283

Wheels with wheel bolt caps
Applies to vehicles: with whee l bo lts w ith caps
The cops must be removed first from the wheel
bolts before the bolts con be unscrewed.
Fig. 214 C hanging a wheel: remov ing the wheel bolt caps
Remo ving
.. Push the pla sti c cli p (provided with the vehicle
tool kit) over the wheel bolt cap unt il the inner
retainers on the clip align with the edge of the
cover.
.. Remove the cap with the
pla s tic cli p (vehicle
tool kit)
q fig . 214.
Refitting
.. Place the caps over the wheel bo lts and push
them back on.
The caps are to protect and keep the whee l bolts
clean.
Loosening and tightening the wheel bolts
The wheel bolts must be loosened before raising
the vehicle.
;::: Fig. 2 15 Changing a wheel: loosen ing t he w heel bolts
0 > CX)
rl I.Cl U"I
rl I.Cl rl
Em ergen cy a ssis tanc e
Loosen ing
.. Slide t he whe el wren ch onto the wheel bolt as
fa r as it will go.
.. Take tight hold of the
end of the wrench hand le
and tur n the wheel bolts
counter -clockwise
about one single turn in the direction of arrow
qfig. 215.
Tightening
.. Slide the wheel wrench onto the wheel bolt as
far as it will go .
.. Take tight hold of the
end of the wrench hand le
and turn each wheel bolt
clo ckwi se until it is
seated.
A WARNING
-- Do not use force or hurry when chang ing a
wheel -you can cause the vehicle to slip off
the jack and cause ser ious persona l inju ries .
-Do not loosen the wheel bolts more than
one turn
befo re you raise the veh icle with
the jack. -You r isk an injury.
(0 Tips
- Never use the hexagonal socket in the han­
dle of the screwdr iver to loosen or tighten
the whee l bolts.
- If a wheel bolt is very tight, you may find it
easier to loosen by ca refully pushing down
on the e nd of the whee l bolt w rench with
one foot only. As you do so, hold on to the
car to keep yo ur balance and take care not
to slip.
285

.... N
0 > CX)
.... I.Cl U"I ,....,
I.Cl ....
-Do not raise the vehicle until you are sure
the jack is securely engaged.
- Passengers must not remain in the vehicle
when it is jacked up.
- Make sure that passengers wait in a safe
p lace away from the vehicle and well away
from the road and traff ic.
- Make sure jack position is correct, adjust
as necessary and then cont inue to raise
the jack.
- Changes in temperature or load can affect
the height of the vehicle.
CD Note
Do not lift the vehicle by the sill. Position the
veh icle jack on ly at the designated lifting
points on the sil l. Otherwise, your vehicle will
be damaged.
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang­
ing the wheel .
Fig. 2 18 Ch anging a whee l: using the screwd river handle
(with the blade removed) to turn the bolts
F ig . 2 19 Ch ang ing a whee l: alig nmen t pin inside the top
hole
Em ergen cy a ssis tanc e
After you have loosened all wheel bolts and
raised the vehicle off the ground, remove and re­
place the wheel as follows:
Removing the wheel
.,.. Use the hexagonal socket in the screwdri ver
handle
to comp letely remove the topmost
wheel bo lt and set it aside on a
clean su rface
c!>fig. 218.
.,.. Screw the threaded end of the alig nment pin
from the tool kit hand-tight into the empty bo lt
hole
r::!> fig . 219.
.,.. Then remove the other wheel bolts as descr ibed
above .
.,.. Take off the wheel leaving the alignment p in in
the bolt hole
~ 0-
Putting on the comp act spare wheel
.,.. Lift the spare wheel and carefully slide it over
the alignment p in to guide it in place
r::!> (0 .
.,.. Use the hexagonal socket in the screwdr iver
handle to screw in and tighten a ll wheel bolts
slightly .
.,.. Remove the alignment pin and insert and t igh t­
en the remaining wheel bo lt s light ly like the
rest .
.,.. Turn the jack hand le counter -clockwise to lower
the vehicle until the jack is fully released .
.,.. Use the wheel bolt wrench to tighten a ll wheel
bolts firmly
r::!> page 285 . Tighten them cross­
wise,
from one bo lt to the (approx imately) op­
posite one, to keep the wheel centered .
CD Note
When removing or installing the wheel, the
rim co uld h it the brake rotor and damage the
r otor. Work carefully and have a second per­
son help you.
0) Tips
Never use the hexagonal socket in the handle
of the sc rewdrive r to loosen or t ighten the
whee l bolts.
- Pull the reversible blade from the screwdr iv­
er before yo u use the hexagona l soc ket in
t he handle to tu rn the whee l bolts.
287

.... N
0 > CX)
rl I.Cl U"I
rl I.Cl ....
Spare tire
General information
Applies to vehicles: with space-saving spare tire (compact
spare tire)
F ig. 220 Luggage co mpa rtmen t: ca rgo floo r fo lded up (A3
Sportback top, A3 sedan bo ttom )
F ig. 221 Compac t spare tir e
The spare tire ¢ fig. 221 is intended for sho rt­
term use only . Have the damaged tire checked
and replaced if necessary by an authorized Aud i
dealer or authori zed Audi Service Facility as soon
as possible .
There are some restrictions on the use of the compact spare tire . The compact spare tire has
been designed specif ica lly for your type of vehi­
cle . Do not replace it with the spare tire from an­
other type of vehicle.
Em ergen cy a ssis tanc e
Removing the sp are tire (A3 Sportback )
.,. Lift up the cargo floor wi th the p lastic handle
until it is clamped beh ind the tabs on both s ide
pane ls
(D ¢ fig. 220.
.,. Remove the subwoofer* if necessary . Check
which subwoofer is installed based on the con ­
nector : version 1 ¢
page 290 or version 2
¢page 290.
"'Turn the large screw counter -clockw ise .
.,. Remove the spare tire .
Removin g the sp are tire (A3 Sedan )
.,. Lift the cargo floor by the plastic handle.
"' Hang the p lastic hook on the luggage compart-
ment weather strip -arrow -¢
fig . 220 .
"'Turn the large screw counter-clockw ise .
"' Remove the spare tire .
Snow chains
For technical reasons, the use of snow chains on
the compact spare tire is not permitted.
If you have to drive with snow chains and a front
tire fails, mount the spare wheel in p lace of a
rear tire . Install the snow chains on the rear tire
that you removed , and install that in place of the
front t ire that fai led .
A WARNING
=
-After installing a spare tire, the t ire pres-
sure must be checked as soon as possible .
The t ire pressure is availab le on ¢
page 263,
fig. 205.
- If the spa re ti re is mo re t han 6 years old,
use it only in an emergency and with ex­
treme ca ution and careful driving.
- The spare tire is intended only fo r tempora­
ry a nd short-term use.
It should be replaced
as soon as poss ible with the normal whee l
and tire .
- After moun ting the compact spare tire, the
tire pressure must be checked as soon as possible. The tire press ure of the compact
spare tire must be 61 ps i (420 kPA); other­
wise, you risk having an accident .
- Do not drive faster than 50 mph (80 km/h).
You risk having an acc ident. ""
289

Emergency assistance
-Avoid full-throttle acceleration, heavy brak­
ing, and fast cornering. You risk having an
accident.
- Never dr ive using more than one spare
wheel and tire. You risk having an accident.
- Normal summer or winter tires must not be
mounted on the compact spare wheel rim.
- For technical reasons, the use of tire chains
on the spare tire is not permitted. If it is
necessary to drive with tire chains, the spare
wheel must be mounted on the front axle in
the event of a flat in a rear tire. The newly
available front wheel must then be installed
in place of the rear wheel with the flat tire.
Installing the tire chain before mounting
the wheel and tire is recommended.
- Loose items in the passenger compartment
can cause serious personal injury during
hard braking or in an acciden t. Never store
the inflatable spa re tire or jack and tools in
the passenger compartment.
- Normal summer or winter tires must not be
mounted on the compact spare wheel rim .
Removing the subwoofer (version 1)
Applies to veh icles: w ith subwoofer
The subwoofer must be removed before the
spare wheel" can be removed.
F ig. 222 Spare wheel well : subwoofer
Removing the subwoofer
.,. Lift up the cargo floor~ page 289, fig. 220 .
.,. Press the connector tabs CD cc> fig . 222 togeth­
er .
.,. Remove the connector @and set the discon­
nected cable aside .
.,. Remove the bolt @ .
290
.,. Carefully remove the su bwoofer.
Installing the subwoofer
.,. Carefully p lace the su bwoofer in the rim well .
The word "FRONT " on the subwoofer must face
forward.
.,. Insert the connecto r that was removed.
.,. Secure the subwoofer with the bolt.
.,. Fold the cargo f loor cover back into place.
Removing the subwoofer (version 2)
Applies to vehicles: wit h subwoo fe r
The subwoofer must be removed before the
spare wheel" can be removed.
Fig. 223 Spa re w hee l we ll: s ubwoofe r
Removing the subwoofer
.,. Lift up the cargo floor ¢page 289, fig. 220.
.,. Pull the lock CD~ fig. 223 toward the cable .
.,. Press the locking tab @down .
.,. Remove the connector @ and set the removed
cable aside .
.,. Remove the bolt@ .
.,. Carefully remove the subwoofer.
Installing the subwoofer
.,. Carefully place the subwoofer in the r im well .
The word "FRONT" on the s ubwoofer must face
forward.
.,. Insert the connector that was removed.
.,. Secure the subwoofer with the bolt .
.,. Fold the cargo floor cover back into place .