
<( co .... N r--N .... 0 r--> co
Indicat or lights
IE -Loss of pressure in at least one ti re c::> ,& .
Check the tires and replace or repair if necessary.
Check/correct the pressures of all four tires. Then
store the tire pressures in the MMI
<=:>page 223.
mm (T ire Pressure Monitoring System) Tire
press ure: System malfuncti on!.
Ifm appears
after switching the ignition on or whi le driving
and the
IE indicator light in the instrument clus
ter blinks for approximately one minute and then
stays on, there is system malfunction . Try to
store the correct tire pressures
c::> page 223 . If
the indicator light does not turn off or turns on
again after a short period of time, drive to an au
thor ized Audi dealer or authorized Audi Service
Faci lity immediately to have the malfunction cor
rected.
A WARNING
- If the tire pressure warning light IE in the
instrument cluster turns on, the pressure in
one or more tires is too low . Reduce the ve
hicle speed immediately and avo id any hard
steering or braking maneuvers. Stop as soon as possible, check the tire and inflate the
t ire to the correct pressure, which is speci
fied on the tire pressure label on the veh icle
<=:> page 214. Driving w ith a t ire with low
pressure c auses the t ire to overheat and can
result in failure of the tire . Low pressure can
also have a negative effect on the driving
and braking behavior of the vehicle .
- T he driver is responsib le for maintaining the
correct tire pressures . You must check the
tire pressures regularly .
- Under certain conditions (such as a sporty
driv ing style, winter conditions or unpaved
roads), the pressure monitor indicator may
be delayed.
- Do not use run-flat tires on your vehicle . Us
ing them when not permitted can lead to
vehicle damage or accidents .
(D Tips
-The tire pressure monitoring system can al
so stop working when there is an ESC mal
function.
Tir es and wheel s
- Us ing snow chains may result in a system
ma lfunction.
- The tires with the identification "AO" or
"RO"
c::> page 211 have been matched with
your Audi tire pressure monitoring system .
We recommend that you use these tires.
- The tire pressure monitoring system can on
ly monitor the tire pressure of the driving
tires. Check the tire pressure of the spare
wheel in the luggage compartment so that if necessary it is ready for use.
Storing tire pressures
App lies to : vehicles wi th Tir e Pressure Mo nito rin g Sys te m in
dic ator
A change in tire pressur e or a change in tires
must be stored in the syst em .
The tire press ure is stored in the MM I.
.,. Make sure before storing that the t ire pressures
of all four tires meet the specified values and
are adap ted to the load. O therwise the system
could malfunction
c::> page 214.
.. Switch on the ignition.
.,. Select: the I MENU I button> Ca r> Sys tem s*
con trol button > S er vice & control > Tire pre s
s u re m on itor > Stor e tire pressu re > Yes , sto re
no w.
(D Tips
Do not store the tire pressures if snow chains
are installed. Otherw ise the system could
malfunction.
223

Care and cleaning
Care and cleaning
General information
Regular, prope r care helps to maintain your vehi
cle's value.
It can a lso be a requirement when
submitting war ranty claims for cor rosion damage
and pa int defects on the body.
The necessary care prod ucts can be obtained
from an autho rized Audi deale r or authorized
Aud i Service Facility. Read and follow the instruc
tions for use on the packaging.
A WARNING
- Using clean ing and care products incorrectly
can be dangero us to your hea lth .
- Always store clean ing and care products out
of reach of children to reduce the r isk of po i
so ning .
@ For the sake of the environment
- Preferably use environmentally-friendly
products when buying cleaning agents.
- Do not dispose of leftove r clean ing and care
products with household t rash.
Car washes
The longer that deposits s uch as insects, bird
droppings, tree sap or road salt remain on the ve h icle, the more the surface can be damaged. High
temperatures such as those caused by sunlight
i n crease the damag ing effect .
Before washing, r inse off heavy deposits with
p lenty of water.
St ubb orn deposits such as bird droppings or tree
sap are best removed with plenty of wate r and a
microfiber cloth.
Also, wash the underside of yo ur vehicle once
road sa lt stops being used for the season .
Pressure washers
When washing your veh icles with a pressure
washer, always follow t he ope ra ti ng ins tructions
p rovided w ith the pressure washer. This is espe
cially important in regard to the pressure and
spraying distance . Do not direct the stream of
224
water d irect ly onto seals for the side windows,
doors, luggage compartment lid or hood or onto
the tires, r ubber hoses, insulat ing mater ia l, the
power top, sensors* or camera lenses*. Keep a
distance of at least 16 in (40 cm).
Do not remove snow and ice with a pressure
washe r.
Never use rot ary no zzles or high pressure no z
z les .
The wate r temperatu re must not be above 140 °F
(60 °().
Automatic car washes
Spray off the ve hicle before wash ing.
Make su re t hat the windows and power top are
closed and the windsh ield wipers are off. Follow
i nstruct ions from the car wash operator, espe
c ially if there are accessories attached to your ve
hicle.
If possible, use car washes that do not have
brushes.
Washing by hand
Clean the vehicle starting from the top and work
ing down using a soft sponge or cleaning brush .
U se solvent-free cleaning products .
Washing vehicles with matte finish paint by
hand
To avoid damaging the pa int when washing, first
remove dust and large part icles from your vehi
cle. Insects, grease spots and f ingerprints are
best removed w ith a special cleaner for matte
finish paint .
Apply the product using a microf iber cloth. To
avo id damag ing the pa int surface, do not use too
much pressure.
Rinse the veh icle thorough ly with water. Then
clean using a neutra l shampoo and a soft m icro
fiber cloth.
Rinse the vehicle thoroughly again and let it air
dry. Remove any water residue using a sham my.
Stubborn deposits such as bird dropp ings or tree
sap are best removed with plenty o f water and a
microfiber cloth. .,..

<( co ..... N
" N ..... 0 r--. > 00
@ Tips
The vehicle jack* in your vehicle is maintena nee-free.
Tire mobility kit
Preparation
A ppl ies to: ve hicles with tire mobility kit
~ Read and f ollow th e imp ortant saf ety pre cau
t io ns ¢
page 230, General information .
~ Check if a repair with the t ire mobility k it is pos
sible
¢ page 231.
Using the tire mobility kit
Appl ies to: ve hicles with tire mobility kit
Fig. 174 Tire: t ire da mage t hat ca nnot be repa ired
The ti re repa ir is on ly meant for temporary use .
Change the spare t ire as soon as possible ¢ ,& .
If the tire is pierced by an object such as a nail,
do not remove the object from the tire.
T he tire repair set is able to be used at tempera
tures as low as -4 °F ( -20 °C).
Th e tir e mobil it y k it ma y not be u sed :
-if the t ire has cuts or punctures that are larger
than
0.1 6 in (4 mm ) (D ¢ fig. 174 .
-if th e rim is damaged @.
- if you drove with very low tire pressure or with -
ou t air in th e tire @.
See an au thorized Aud i dealer or authorized Aud i
Service Facility for assistance in these situations.
Em ergen cy a ssis tanc e
A WARNING
--Please note that the tire mobility kit cannot
be used in all situations, and that it may on
ly be used temporarily.
- The tire sealant must not come in contact
with skin, eyes , or clothes.
- If tire sealant gets in your eyes or on your
skin, thoroughly rinse the affected area im
mediately with clean water .
- Do not inhale the fumes.
- If you swa llow any of the tire sealant, thor-
oughly rinse your mouth immediately and
drink a lot of water . Do not induce vomiting .
Seek med ical attention immed iate ly .
- Change your clothes immediately if they get
tire sealant on them.
- If an allergic reaction occurs, seek immedi
ate med ical attention .
- Keep the t ire sealant away from children.
- In vehicles with a tire pressure monitor ing
system*, using tire sealant can results in an incorrect d isplay or a system malfunction.
Drive carefully to the nearest authorized
Aud i dealer or authorized Audi Serv ice Facili
ty .
@ Tips
-If sea lant leaks, allow it to dry in place. You
can then peel it off like a st icker.
- Note the expiration date on the sealant bot
tle. Rep lace the tire sealant at an aut hor
ized Aud i deale r or autho rized Aud i Serv ice
Facility .
- Radio reception can be interrupted when
operating the compressor* .
- Obey all laws.
231

Emergency assistance
Repairing tires
Applies to: vehicles with tire mobility kit
Fig. 175 Components of the tire mobility kit
F ig. 176 Tire mobility k it connecti on
Requirement: the tire mobility kit must be laid
out and ready for use
o page 230, Vehicle tool
kit .
Installing the tire mobility kit
• Open the cover @on the compressor
9fig. 175.
• Remove the connector @) and pressure hose®
with pressure gauge from the housing.
• Install the compressor pressure hose® onto
the flange @ of tire sealant bottle@.
• Insert the sealant bottle with the flange at the
bottom into the opening @ on the compresso r
cover .
... Remove the valve cap from the fau lty tire.
• Install the filler hose @onto the valve
0
ofig. 176.
• Connect the plug @o fig. 175 to a socket in
the vehicle.
• Switch on the ignition.
Inflating a tire
... Move the switch @ o fig. 176 on the compres
sor into posit ion I.
232
... Inflate the tire to between 29 psi (200 kPA)
and 36 psi (250 kPA) and read the pressure on
the gauge.
• If this tire pressure is not reached, drive your
vehicle approximate ly 33 ft (10 meters) for
ward or backward so that the sealant can be re
distr ibuted inside the tire .
.&_ WARNING
- Read and follow the manufacturer's safety
precautions on the compressor and in the
instructions on the bottle of sealant .
-If a tire pressure of 29 psi (200 kPA) cannot
rea ched after inflati ng for 6 minutes, then
the tire is too severely damaged. Do not
continue driving.
- If the tire cannot be repaired with the tire
sealant, see an authorized Audi dealer or au
thorized Audi Service Facility for assistance.
(D Tips
Do not operate the compressor for more than
6 minutes continuously, or it can overheat.
Once the compressor has cooled, you can con
tinue to use it .
Completing
Applies to: vehicles with tire mobility kit
... Adhere the sticker that says "max. SO mph
(max. 80 km/h)" that is provided with the tire
mob ility kit w ith in the driver's field of vision.
... Stop the vehicle after driv ing for about 10 mi
nutes and check the t ire pressure.
• If the tire pressure is lower than 19 psi (130
kPA), then the tire is too severely damaged . Do
not con tinue dr iving. See an authorized Audi
deale r o r authorized Audi Service Facility for as
sistance.
... If the tire pressure is at least 19 psi (130 kPA),
adjust the tire pressure to the specified value
o page 214, Tire pressure. Store the tire pres
sures
o page 223, Storing tire pressures. Drive
to the nearest authorized Audi dealer or au
thorized Audi Service Facility to have the tire re-
placed. ..,.

<( co ..... N
" N ..... 0 r--. > 00
A WARNING
If the tire pressure is less than 19 psi
(130 kPA) after 10 minutes of driving , then
the ti re is too severely damaged . Do not con
tinue dr iv ing . See an authorized Audi dealer
or authorized Aud i Servi ce Fac ility for assis
tance .
A WARNING
Pay attent ion to the following after repair ing
the tire:
- Do not drive faster than SO mph (80 km/h).
- Avoid hard acceleration, brak ing sharp ly,
and fast cornering.
- The veh icle may become more difficult to
control.
- If the t ire is too severely damaged, see an
authorized Audi dealer or authorized Aud i
Service Facility for assistance .
@ For the sake of the environment
You can give the used tire sealant bottle to an
author ized Audi dealer or authorized A udi
Serv ice Facility for disposal.
(I_) Tips
Remember to obtain a new bottle of sealant
from an authorized Aud i dea ler or authorized
Aud i Service Facility after repairing a tire.
Spare tire
General information
Applies to: vehicles with space-saving spare tire (compact
spare tire)
Fig. 177 L ugg age co mpa rtment : ca rgo floo r cover folded
up ward
Em ergen cy a ssis tanc e
Fig. 178 Spa re t ire (examp le )
The spare tire ¢ fig. 178 is intended for short
te rm use only. Have the damaged tire checked
and replaced if necessary by an author ized Audi
dealer or authorized A udi Service Facility as soon
as possible.
T here are some restr ictions on the use of the
compact spare tire . The compact spare t ire has
been designed specifically for your type of vehi
cle. Do not rep lace it with the spare tire from an
other type of vehicle.
Removing the spare tire
.,. Lift the cargo floor by the p lastic handle .
.,. Hang the plastic hook on the luggage compart -
ment seal@¢
fig. 177.
.,. Turn the large screw counter-clockwise .
.,. Remove the spare tire.
.. Unhook the cargo floor befo re closing the lug -
gage compartment lid .
Snow chains
For technical reasons, the use of snow chains on
the compact spare tire is not permitted.
If you have to dr ive with snow chains and a front
t ire fails, mo unt the spare wheel in p lace of a
rear tire. Install the snow chains on the rear tire
that you removed, and install that in place of the
front t ire that fai led .
A WARNING
--After installing a spare tire, the t ire pres
sure must be checked as soon as possible.
The tire pressure is available one:>
page 214,
-
rg.111 . ~
233

Emerg enc y assis ta nc e
-If the spare tire is more than 6 years old,
use it only in an emergency and with ex
treme caution and careful dr iving .
- The spare tire is intended on ly for tempora
ry and short-term use. It should be replaced
as soon as possible with the normal wheel and t ire .
- After mounting the compact spare t ire, the
t ire pressure must be checked as soon as
poss ible . The tire pressure of the compact
spare tire must be
61 psi (420 kPA); other
wise, you risk hav ing an accident.
- Do not drive faster than
50 mph (80 km/h).
You risk hav ing an accident.
- Avoid full -throttle accelerat ion, heavy brak
ing, and fast cornering. You risk having an
acc ident.
- Never dr ive using more than one spare
wheel and tire. You risk having an acc ident .
- Normal summer or winter tires must not be mounted on the compact spare wheel rim.
- For technical reasons, the use of tire chains
on the spare tire is not perm itted. If it is
necessary to drive with t ire chains, the spare
wheel must be mounted on the front axle in
the event of a flat in a rear tire. The new ly
available front wheel m ust then be insta lled
in place of the rear wheel with the flat tire.
Installing the tire chain before mounting
the wheel and tire is recommended.
- Loose items in the passenger compartment
can cause serious personal injury during
hard braking or in an accident. Never store
the inflatable spare t ire or jack and too ls in
the passenger compartment.
- Normal summer or winter tires must not be
mounted on the compact spare wheel rim.
Replacing wheels
Before changing a wheel
Observe the following precautions for your own
and your passenger's safety when changing a
wheel.
.,. After you experience a tire failure, pull the car
well away from moving traff ic and try to reach
le vel ground before you stop¢_& .
234
.. All passengers should lea ve th e car and move
to a safe location (for instance, behind the
guardrail) ¢ _& .
.. Engage the
par king br ake to prevent your vehi
cle from rolling unintentionally¢_& .
.. Move
selec tor le ve r to p osition P ¢ _& .
.. If you are towing a tra iler , u nhitch the trailer
from your vehicle.
.. Ta ke the
jac k¢ page 230 and the spar e tir e
¢ page 233 out of the luggage compa rtment.
A WARNING
-
You or your passengers could be injured while
changing a whee l if you do not follow these
safety precautions:
- If you have a flat tire, move a safe distance off the road. Turn off the engine, turn the
emergency f lashers on and use other warn
ing dev ices to alert other motorists.
- Make sure that passengers wait in a safe
place away from the vehicle and well away
from the road and traff ic.
- To help prevent the veh icle from moving
suddenly and possibly slipping off the jack,
always fully set the parking brake and block
the wheel diagonally opposite the wheel be
ing cha nged . When one front wheel is lifted
off the ground, placing the Automat ic
T ransmiss ion in P (Park) will
not prevent the
veh icle from moving.
- Before you change a whee l, be sure the
gro und is level and firm . If necessary, use a
sturdy board under the jack.
- Always sto re the vehicle too l kit, the jack
and the replaced tire in the luggage com
par tment
¢page 130.
Changing a wheel
When you change a wheel, follow the sequence
described below step-by-step and in exactly that
order.
1. Remove the decorati ve wh eel co ver* . For
more detai ls see also ¢
page 235, Decora
tive wheel covers
or ¢ page 235, Wheels
with wheel bolt caps .
2. Loosen the wh ee l bolt s ¢page 236.

<( co ..... N
" N ..... 0 r--. > 00
3. Locate the proper mounting point for the
jack and align the jack below that poin t
¢page 236.
4. Raise the car with the jack¢ page 236.
5. Remove the wheel with the flat tire and then
install
the spare ¢ page 238.
6. Tighten all wheel bolts lightly.
7. Lower the veh icle with the jack.
8. Use the wheel bolt wrench and firmly tighten
all wheel bolts
¢page 236 .
9. Replace the decorative wheel cover* .
_& WARNING
Always read and follow all WARNINGS and in
formation
¢ .&. in Raising the vehicle on
page
237 and ¢ page 239.
After changing a wheel
A wheel change is not complete without the do
ing the following .
.,. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
¢ page 130.
.,. Check the tire pressure on the spar e wheel im
mediate ly after mount ing it .
.,. As soon as possible, have the
tightening tor
ques
on all wheel bolts checked with a torque
wrench . The correct tightening torque is
90 ft
lb
(120 Nm) .
.,. Have the flat tire
replaced as soon as possible .
(D Tips
-If you notice that the wheel bolts are cor
ro ded and difficult to turn while changing a
tire , they should be replaced before you
check the tightening torque .
- Drive at reduced speed until you have the
tightening torques checked.
-Af ter changing a wheel, the tire pressure in
all four tires must be checked/corrected and
the tire pressure monitoring indicator must
be stored in the MMI
9page 223.
Emergency assistance
Decorative wheel covers
Applies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 179 Changing a whe el: Removin g the wh eel cov er
Removing
.,. Insert the hook (provided w ith the vehicle tool
kit) in the hole in the wheel hub cover.
.,. Pull off the
decorative wheel cover¢ fig. 179.
Wheels with wheel bolt caps
Applies to: vehicles with wheel bolts w,th caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed.
Fig. 180 Chang ing a whee l: removing th e whee l bol t cap s
Removing
.,. Push the plastic clip (provided with the vehicle
tool kit) over the wheel bolt cap until the inne r
reta iners on the clip align with the edge of the
cover.
.,. Remove the cap with the
plastic clip (vehicle
tool kit)
¢ fig. 180.
Refitting
.,. Place t he caps over the wheel bolts and push
t hem back on.
235

<( co .... N r--N .... 0 r--> co
-If the spare tire has to be installed in the incor
rect direction, use the s pare tire only tempora
ri ly s ince the tire w ill not be ab le to achieve its
opt imum performance c haracter istics with re
gard to aquaplaning, noise and wear .
- We recommend that you pay particular atten
tion to this fact during wet weathe r and that
yo u ad just yo ur speed to match road condi
t io ns.
- Replace t he f lat t ire with a new one and have it
insta lled on yo ur vehicle as soon as possible to
r e store the handling adva ntages of a unid irec
t io na l t ire .
Notes on wheel changing
Please read the i nfo rma tion ¢ page 211 if y ou
ar e goi ng to use a sp are tir e which i s different
fr om t he tires on yo ur vehicle.
Af ter you ch an ge a tire:
-Check the tire pressure on the spare immedi
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos
sible by your authorized Audi dealer or a
qualified service station .
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi
ble . Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds .
.8, WARNING
- If you are going to e quip yo ur ve hicl e w ith
tir es or r ims w hic h diff er from t hose whi ch
w ere fa cto ry i nst alled, t hen be s ure t o read
t h e informat ion ¢pa ge
211.
- Alw ays mak e sure the d amag ed whee l or
even a flat tire and t he jack and tool ki t are
-
Emergency assistance
proper ly sec ure d in the l ugga ge compart
ment a nd a re not loose in the passenger
compa rtm ent.
- In an accident or sudden maneuver they
could fly forward, injuring a nyone in the ve
h icle.
- A lways sto re damaged wheel, jack and tools
securely in the l uggage compartment. Ot h
erw ise , in an acc ident or sud den maneuve r
they cou ld fly forwar d, causing injury to pas
s en ger s in the vehicle .
239