2016 AUDI A3 CABRIOLET spare tire

<( co ..... N
" N ..... 0 r--. > 00
3. Locate the proper mounting point for the
jack and align the jack below that poin t
¢page 236.
4. Raise the car with the jack¢ page 236.
5. Remove the wheel with the flat tire and then
install
the spare ¢ page 238.
6. Tighten all wheel bolts lightly.
7. Lower the veh icle with the jack.
8. Use the wheel bolt wrench and firmly tighten
all wheel bolts
¢page 236 .
9. Replace the decorative wheel cover* .
_& WARNING
Always read and follow all WARNINGS and in­
formation
¢ .&. in Raising the vehicle on
page
237 and ¢ page 239.
After changing a wheel
A wheel change is not complete without the do­
ing the following .
.,. Always store the vehicle tool kit, the jack* and
the replaced tire in the luggage compartment
¢ page 130.
.,. Check the tire pressure on the spar e wheel im­
mediate ly after mount ing it .
.,. As soon as possible, have the
tightening tor­
ques
on all wheel bolts checked with a torque
wrench . The correct tightening torque is
90 ft
lb
(120 Nm) .
.,. Have the flat tire
replaced as soon as possible .
(D Tips
-If you notice that the wheel bolts are cor­
ro ded and difficult to turn while changing a
tire , they should be replaced before you
check the tightening torque .
- Drive at reduced speed until you have the
tightening torques checked.
-Af ter changing a wheel, the tire pressure in
all four tires must be checked/corrected and
the tire pressure monitoring indicator must
be stored in the MMI
9page 223.
Emergency assistance
Decorative wheel covers
Applies to: vehicles with decorative wheel covers
The decorative wheel covers must be removed
first to access the wheel bolts .
Fig. 179 Changing a whe el: Removin g the wh eel cov er
Removing
.,. Insert the hook (provided w ith the vehicle tool
kit) in the hole in the wheel hub cover.
.,. Pull off the
decorative wheel cover¢ fig. 179.
Wheels with wheel bolt caps
Applies to: vehicles with wheel bolts w,th caps
The caps must be removed first from the wheel
bolts before the bolts can be unscrewed.
Fig. 180 Chang ing a whee l: removing th e whee l bol t cap s
Removing
.,. Push the plastic clip (provided with the vehicle
tool kit) over the wheel bolt cap until the inne r
reta iners on the clip align with the edge of the
cover.
.,. Remove the cap with the
plastic clip (vehicle
tool kit)
¢ fig. 180.
Refitting
.,. Place t he caps over the wheel bolts and push
t hem back on.
235

Emergency assistance
Taking the wheel off/installing the spare
Follow these instructions step-by-step for chang ­
ing the whee l.
F ig. 184 Chang ing a wheel: using the screw driver ha ndl e
(wit h th e bla de re m oved) to turn the bol ts
F ig . 185 Chang ing a whee l: alignment p in inside t he top
hole
Afte r you h ave loose ned a ll w heel bo lts and
raised t he ve hicl e off the groun d, remove and re­
p lace the whee l as fo llows:
Removing the wheel
• Use the hexagonal so cket in the screwdriver
handle
t o comple tely remove the topmost
whee l bolt and se t it aside on a
clean surface
~fig. 184 .
• Scre w the th reade d end of the alignment pin
from the tool kit hand-tight into the empty bolt
hole
c> fig. 185 .
• The n remove the other wheel bolts as described
above.
• Takeoff the wh eel leav ing the a lignm ent pin in
t h e bolt ho le
¢ 0 .
Putting on the compact spare wheel
• Lift the spare wheel and carefully slide it ove r
the alignme nt pin to gui de it in place
c> 0 .
238
• Use the hexagonal socket in the screwdriver
handle to screw in and tighten a ll wheel bo lts
slightly .
• Remove the alignment pin and insert and tight­
en the remaining wheel bo lt s light ly like the
rest .
• Tur n t he jack hand le co unter-clockw ise to lowe r
the vehicl e until t he ja ck is fu lly released .
• Use the wheel bo lt wren ch to tig hte n all wheel
bolts firm ly¢
page 236. T igh ten them cro ss ­
wise,
from one bo lt to t he (a pprox ima tely) op­
posite one, to keep the wheel centered.
(D Note
W hen re mov ing o r installin g the w heel, the
rim co uld hit the bra ke r otor an d damage t he
r otor . Work care fully and h ave a second per­
son he lp yo u.
(D Tips
Neve r use the he xagonal socke t in the han dle
of the sc rew drive r to loosen or t ighten the
whee l bolts .
- Pull the reve rsible blade from the screwdr iv ­
er befo re yo u use t he hexagona l so cket in
t h e handle to t urn the whee l bolts.
- W he n mo unting tires with
unidirectional
tread design
make sure the trea d pattern is
pointed t he right way~
page 238.
-Th e wheel bolts s ho uld be clean an d easy to
t u rn. Check fo r dirt and corrosion o n the
mati ng surfaces of both the wheel and the
hub. Remove all dirt from these s urfaces be­
fore r emounting the whee l.
Tires with unidirectional tread design
Tires with unidirectional tread design must be
mounted with their tread pattern pointed in the
right direction .
Using a spare tire with a tread pattern
intended for use in a specific direction
When using a spare tire wit h a tread patter n in ­
te nded for use in a specific direction, please note
the followi ng:
- The direction of rotation is marked by an arrow
on the side of the tire. ..,.

<( co .... N r--­N .... 0 r--­> co
-If the spare tire has to be installed in the incor ­
rect direction, use the s pare tire only tempora­
ri ly s ince the tire w ill not be ab le to achieve its
opt imum performance c haracter istics with re ­
gard to aquaplaning, noise and wear .
- We recommend that you pay particular atten­
tion to this fact during wet weathe r and that
yo u ad just yo ur speed to match road condi ­
t io ns.
- Replace t he f lat t ire with a new one and have it
insta lled on yo ur vehicle as soon as possible to
r e store the handling adva ntages of a unid irec­
t io na l t ire .
Notes on wheel changing
Please read the i nfo rma tion ¢ page 211 if y ou
ar e goi ng to use a sp are tir e which i s different
fr om t he tires on yo ur vehicle.
Af ter you ch an ge a tire:
-Check the tire pressure on the spare immedi­
ately after installation.
- Have the wheel bolt tightening torque
checked with a torque wrench as soon as pos­
sible by your authorized Audi dealer or a
qualified service station .
- With steel and alloy wheel rims, the wheel
bolts are correctly tightened at a torque of
90 ft lb (120 Nm) .
- If you notice that the wheel bolts are corroded
and difficult to turn while changing a tire,
they should be replaced before you check the
tightening torque.
- Replace the flat tire with a new one and have
it installed on your vehicle as soon as possi­
ble . Remount the wheel cover.
Until then, drive with extra care and at reduced
speeds .
.8, WARNING
- If you are going to e quip yo ur ve hicl e w ith
tir es or r ims w hic h diff er from t hose whi ch
w ere fa cto ry i nst alled, t hen be s ure t o read
t h e informat ion ¢pa ge
211.
- Alw ays mak e sure the d amag ed whee l or
even a flat tire and t he jack and tool ki t are
-
Emergency assistance
proper ly sec ure d in the l ugga ge compart­
ment a nd a re not loose in the passenger
compa rtm ent.
- In an accident or sudden maneuver they
could fly forward, injuring a nyone in the ve­
h icle.
- A lways sto re damaged wheel, jack and tools
securely in the l uggage compartment. Ot h­
erw ise , in an acc ident or sud den maneuve r
they cou ld fly forwar d, causing injury to pas­
s en ger s in the vehicle .
239

<( co .... N ,.__
N .... 0 ,.__
> co
@ For the sake of the environment
-Changing the engine settings will adversely
affect emission levels. This is detrimental to
the environment and increases fuel con­
sumption.
-Always observe environmental regulations
when disposing of old engine oil, used brake
fluid, dirty engine coolant, spent batteries
or worn out tires.
- Undeployed airbag modules and pretension­
ers might be classified as Perchlorate Mate­
rial -special handling may apply, see
www .dtsc.ca.gov/hazardouswaste/perchlo­
rate . When the vehicle or parts of the re­
straint system including airbag modules
safety belts with pretensioners are scrap­
ped, all applicable laws and regulations
must be observed. Your authorized Audi
dealer is familiar with these requirements
and we recommend that you have your deal­ er perform this service for you.
Accessories and
technical changes
Additional accessories and parts replacement
Always consult an authorized Audi dealer before
purchasing accessories.
Your vehicle incorporates the latest safety design
features ensuring a high standard of active and passive safety.
This safety could be compromised by non-ap­ proved changes to the vehicle. For this reason, if
parts have to be replaced, please observe the fol­
lowing points when installing additional accesso­
ries:
Approved Audi accessories and genuine Audi parts are available from authorized Audi dealers.
These dealers also have the necessary facilities, tools and trained specialists to install the parts
and accessories properly .
Consumer information
A WARNING
Using the wrong spare parts or using non-ap­
proved accessories can cause damage to the
vehicle and serious personal injury.
- Use only accessories expressly approved by
Audi and genuine Audi spare parts
- These parts and accessories have been spe­
cially designed to be used on your vehicle.
- Never install accessories such as telephone
cradles or beverage holders on airbag covers
or within the airbag deployment zones. Do­
ing so will increase the risk of injury if air­
bags are triggered in an accident!
- Before you check anything in the engine
compartment, always read and heed all
WARNINGS 9page 188.
(D Note
-If items other than genuine Audi spare
parts, add-on equipment and accessory
items are used or if repair work is not per­
formed according to specified methods, this
can result in severe damage to your vehi­
cle's engine and body (such as corrosion)
and adversely affect your vehicle's warranty.
- If emergency repairs must be performed
elsewhere, have the vehicle examined by an
authorized Audi dealer as soon as possible.
- The manufacturer cannot be held liable for
damage which occurs due to failure to com­
ply with these stipulations.
Technical Modifications
Our guidelines must be complied with when tech­
nical modifications are made.
Always consult an authorized Audi dealer
before
starting work on any modifications.
This will help ensure that vehicle function, per­
formance and safety are not impaired
9 ,& .
Attempting to work on electronic components
and the software used with them can cause mal­
functions. Because of the way electronic compo­
nents are interconnected with each other, such
malfunctions can also have an adverse affect on
other systems that are not directly involved. This ..,.
255

<( co .... N ,.__
N .... 0 ,.__
> co
Snow chains ... ................ ..... .
All whee l drive ................ ..... .
Socket .. .. .. . . ............... .. .... ..
Sources of information about child restraints
219
120
56
and the ir use . . . . . . . . . . . . . . . . . . . . . . . . . 183
Spare tire ... .. ................ ..... . 230
Speed limiter . . . . . . . . . . . . . . . . . . . . . . . . . 88
Speedometer 23
Speed warn ing system . . . . . . . . . . . . . . . . . . 88
Sport mode . . . . . . . . . . . . . . . . . . . . . . . . . . 117
Stabili zation program
refer to Electronic Stabilization
Control (ESC) . . . . . . . . . . . . . . . . . . . . . . .
116
Star button . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
S TART ENGINE STOP button (convenience
key) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
70
START ENGINE STOP (convenience key) 71
Starting
Hill hold ... .. ................ ..... ..
75
Starting from a stop
Hill start ass ist . . . . . . . . . . . . . . . . . . . . . . .
74
St arting (engine)
Malfunction (button) . . . . . . . . . . . . . . . . . .
70
Malfunction (key) . . . . . . . . . . . . . . . . . . . . . 68
W ith button . . . . . . . . . . . . . . . . . . . . . . . . . 70
With key . ...... .. .. .... ... .. .. .. .. .. 68
Steering
Electromechanical steering ..... .. ...
119, O
Indicator light . . . . . . . . . . . . . . . . . . . . . . .
1 7
Lock ing steering (ignition key) . . . . . . . . . . 69
Lacking the steer ing (button) . . . . . . . . . . . 71
Lock ing ( ignition lock) . . . . . . . . . . . . . . . . . 68
also refer to Electromechanical steering 119
Steering wheel
adjust ing . . . . . . . . . . . . . . . . . . . . . . . . . . .
67
Buttons .. .. .. ...... .... ..... .. .. .... 24
Multifunction steering wheel . . . . . . . . . . .
23
Shift paddles (automatic transmission) . . . 81
Steps for determining correct load limit . . . 218
Stopping (engine)
with button . . . . . . . . . . . . . . . . . . . . . . . . .
71
with key . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Storage compartments . . . . . . . . . . . . . . . . . 57
Storage hooks . . . . . . . . . . . . . . . . . . . . . . . . . 60
S tronic (automatic transmission) . . . . . . . . .
76
Sun visors . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Index
Switching daytime running lights on and off 45
Switching the ignition on/off (with key) . . . .
68
Symbols
refer to Indicator lights . . . . . . . . . . . . . . . . 12
System indicator light (M IL) .......... 19, 21
T
Tachometer . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Technical data . . . . . . . . . . . . . . . . . . . . . . . . 250
Technical modifications . . . . . . . . . . . . . . . . 255
Temperature display
Coo lant . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10
Outside temperature . . . . . . . . . . . . . . . . . . 11
Tether anchors . . . . . . . . . . . . . . . . . . . . . . . 18 1
Tether strap . . . . . . . . . . . . . . . . . . . . . . . . . 181
T he first 1,000 miles (1,500 km) and after-
wards...... .... .. ................. .. .
65
Tie-downs .. .... .. ................ 59, 131
tiptronic (automatic transmission) . . . . . . . . 81
Tire Mobility System . . . . . . . . . . . . . . . . . . . 230
Tire Mobility System (tire repair set) . . . . . . 23 1
Tire repair kit ... .. .. ............. .. . .
Tires .......... ... .. ................ .
Low aspect ratio tires ............ .. . .
R . epa1r set . .. .. .. .... ... . .... ... .. . .
Replacing ... .. . ............ ...... . .
Service life
T ire pressure
Tire pressure mon itoring system ...... .
Tire pressure table . ................. .
Tread wear indicators .............. . .
Unidirectional .... ......... .... .... . .
Uniform tire quality grading ....... .. . .
Tires and wheels
Glossary of tire and loading terminology .
Tires and vehicle load limits ....... .. . .
To ols
.... .. .. .. .. ............... .. ..
Torn or frayed safety belts ...... .... .. . .
Towing Tow trucks
230
204
220
231
234
212
214
222
215
212
206
221
206
216
230
137
246
T owing loop . . . . . . . . . . . . . . . . . . . . . . . . .
247
TPMS (tire pressure moni toring system) . . . 222
Trailer mode . . . . . . . . . . . . . . . . . . . . . . . . . . 85
Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 86
267