2016 Alfa Romeo 4C Spider display

Service Warning Indicator Light – If Equipped
Yellow TelltaleLight What It Means
Service Warning Indicator Light
The “Scheduled Servicing Plan” includes vehicle maintenance at fixed intervals, refer to the
Maintenance
chapter. This message is displayed automatically along with the warning light
when the key is turned to MAR-ON - 1242 miles (2,000 km) before these deadlines and reap-
pears every 124 miles (200 km). Below 124 miles (200 km) servicing indications are more fre-
quent. The indication will appear in miles or kilometers according to the Unit Of Measure-
ment settings. When the next scheduled service is approaching and the key is turned to
MAR-ON, the word Service will appear on the display, followed by the number of miles or
kilometers left. Contact a dedicated authorized dealership. The operations in the “Scheduled
Servicing Plan” will be performed and the message will be reset.
140 UNDERSTANDING YOUR INSTRUMENT PANEL

ELECTRONIC VEHICLE INFORMATION CENTER
(EVIC)The Electronic Vehicle Information Center (EVIC) fea-
tures a driver-interactive display that is located in the
instrument cluster.
The EVIC consists of the following:
•Digital Speedometer
• Vehicle Info
• Fuel Economy Info
• Trip Info
• Screen Setup
• Vehicle Settings
Electronic Vehicle Information Center (EVIC)
146 UNDERSTANDING YOUR INSTRUMENT PANEL

The system allows the driver to select information by
pushing the following buttons mounted on the instru-
ment panel to the left of the steering column:•
UP Arrow Button
Push and release the UParrow button to scroll
upward through the main menu and sub-
menus or to increase the displayed value. Out-
side of the menu, the UParrow will adjust the
brightness of the instrument panel.
• DOWN Arrow Button
Push and release the DOWNarrow button to
scroll downward through the main menu and
submenus or to decrease the displayed value.
Outside of the menu, the DOWNarrow will
adjust the brightness of the instrument panel.
• SET/BACK Arrow Button
Push and release the SET/BACKarrow button to access/
select the information screens or submenu screens of a
EVIC Control Buttons
4
UNDERSTANDING YOUR INSTRUMENT PANEL 147

3. Briefly push theSET/BACKbutton to store the new
setting and go back to the main menu option previ-
ously selected.
Selecting An Option Of The Main Menu With Sub-
menu
1. Briefly push the SET/BACKbutton to display the first
submenu option.
2. Push the UP
orDOWNarrow button (by a
single push) to scroll through all the submenu
options.
3. Briefly push the SET/BACKbutton to select the dis-
played submenu option and to open the relevant setup
menu.
4. Push the UP
orDOWNarrow button (by a
single push) to select the new setting for this
submenu option.
5. Briefly push the SET/BACKbutton to store the new
setting and go back to the previously selected sub-
menu option.
6. Push and hold the SET/BACKbutton to return to the
main menu (short hold) or the main screen (longer
hold).
Speed Buzzer (Speed Limit)
With this function, it is possible to set the vehicle speed
limit (MPH or km/h) to immediately alert the driver
when the set limit is exceeded.
To set the speed limit, proceed as follows:
1. Briefly push the SET/BACKbutton. The display will
show the message (Speed Buzzer).
2. Push and release the UP
orDOWNarrow
button to select speed limit activation (On) or
deactivation (Off). 4
UNDERSTANDING YOUR INSTRUMENT PANEL 149

3. When the function is activated (On), briefly push theSET/BACK button to display the previously set speed.
Pushing the UP
orDOWNarrow buttons
selects the speed limit. Push SET/BACKto confirm
selection.
NOTE: The setting can be increased or decreased by 5
MPH or km/h each time the UP
orDOWNarrow
button is pushed for speed settings above 20 MPH
(32 km/h). To increase or decrease the set speed
rapidly, push and hold the UP
orDOWNarrow
button. Save the setting by briefly pushing the button
when you approach the required setting.
• Briefly push the SET/BACKbutton to go back to the
menu screen, or push and hold the SET/BACKbutton
(approximately one second) to go back to the main
screen without storing the settings. To cancel the setting, proceed as follows:
1. Briefly push the
SET/BACKbutton. “On” will display.
2. Push and release the DOWN
button. “Off” will
display.
3. Briefly push the SET/BACKbutton to go back to the
menu screen, or push and hold the SET/BACKbutton
(approximately one second) to go back to the main
screen without storing the settings.
Trip B Activation
Through this option, it is possible to activate (On) or
deactivate (Off) the Trip B (partial trip) display.
For further information, see “Trip Computer.”
150 UNDERSTANDING YOUR INSTRUMENT PANEL

For activation/deactivation, proceed as follows:
1. Briefly push theSET/BACKbutton. “On” or “Off”
will display in the EVIC (according to previous set-
ting).
2. Push and release the UP
orDOWNarrow
button to select the setting and once selected a beep
will occur to signal the setting is saved.
3. Briefly push the SET/BACKbutton to go back to the
menu screen, or push and hold the SET/BACKbutton
(approximately one second) to go back to the main
screen without storing the settings.
Set Time
This function may be used to set the clock through two
sub-menu items: “Time” and “Mode.” Proceed as follows:
1. Briefly push the
SET/BACKbutton. The display will
show the two sub-menu items “Time” and “Mode.”
2. Push and release the UP
orDOWNarrow
button to navigate the two sub-menu items.
3. Select the required option and then push the SET/
BACK button.
4. When accessing the “Time” sub-menu item, briefly push the SET/BACK button and “hours” will flash on
the display.
5. Push and release the UP
orDOWNarrow
button for setting.
6. Briefly push the SET/BACKbutton and “minutes”
will flash on the display.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 151

7. Push and release theUPorDOWNarrow
button for setting.
NOTE:
•The setting will increase or decrease by one unit each
time the UP
orDOWNarrow button is
pushed. Push and hold the button to increase/
decrease the setting rapidly. Save the setting by
briefly pushing the button when you approach the
required setting.
• Briefly push the SET/BACKbutton to return to the
“Time” sub-function.
• When accessing the “Mode” submenu, briefly push
the SET/BACK button. The previously set display
format will flash on the display.
• Push and release the UP
orDOWNarrow
button to select “24h” or “12h.”
When you have selected the required settings, briefly
push the SET/BACK button to go back to the Time, Mode
sub-menu screen, or push and hold the SET/BACK
button (approximately one second) to go back to the
main screen without storing the settings.
Set Date
This function may be used to set the date (day - month -
year).
To change the date, proceed as follows:
1. Briefly push the SET/BACKbutton and “year” will
flash on the display.
2. Push and release the UP
orDOWNarrow
button for setting.
3. Briefly push the SET/BACKbutton and “month” will
flash on the display.
152 UNDERSTANDING YOUR INSTRUMENT PANEL

4. Push and release theUPorDOWNarrow
button for setting.
5. Briefly push the SET/BACKbutton and “day” will
flash on the display.
6. Push and release the UP
orDOWNbutton for
setting.
NOTE: The setting will increase or decrease by one unit
each time the UP
orDOWNarrow button is
pushed. Push and hold the UP
orDOWNarrow
button to increase/decrease the setting rapidly. Save
the setting by briefly pushing the button when you
approach the required setting.
• Briefly push the SET/BACKbutton to go back to the
menu screen, or push and hold the SET/BACKbutton
(approximately one second) to go back to the main
screen without storing the settings.
Autoclose
With this function active, the doors will automatically
lock at when the vehicle’s speed exceeds 12 MPH
(20 km/h).
To change the setting, proceed as follows:
1. Briefly push the SET/BACKbutton “On” or “Off” will
flash on the display (according to the previous set-
ting).
2. Push and release the UP
orDOWNarrow
button for setting.
3. Briefly push the SET/BACKbutton to go back to the
menu screen, or push and hold the SET/BACKbutton
(approximately one second) to go back to the main
screen without storing the settings.
4
UNDERSTANDING YOUR INSTRUMENT PANEL 153