2016 Alfa Romeo 4C light

103)The vehicle's driving characteristics
will be modified with the space-saver wheel
fitted. Avoid violent acceleration and
braking, abrupt steering and fast cornering.
The overall duration of the space-saver
wheel is about 3000 km, after which the
relevant tyre must be replaced with another
one of the same type. Never install a
standard tyre on a rim that is designed for
use with a space-saver wheel. Have the
wheel repaired and refitted as soon as
possible. Using two or more space-saver
wheels at the same time is forbidden. Do
not grease the threads of the stud bolts
before fitting them: they might slip out.
104)The jack is a tool developed and
designed only for changing a wheel, if a
tyre gets punctured or damaged, on the
vehicle with which it is supplied or on other
vehicles of the same model. Any other use,
e.g. to jack up other vehicle models or
different things, is strictly prohibited. Never
use it to carry out maintenance or repairs
under the vehicle or to change
summer/winter wheels and vice versa.
Never position yourself under a jacked
vehicle. If any work under the vehicle is
necessary, contact the Alfa Romeo Service
Network. Incorrectly positioning the jack
may cause the vehicle to fall: use it only in
the positions indicated. Do not use the jack
for loads higher than the one shown on its
label. Never start the engine with vehicle
raised. If the vehicle is raised more than
necessary, everything can become more
unstable, with the risk of the vehicle
dropping violently. Thus, lift the vehicle only
as needed in order to access the spare
tyre.
105)The space-saver wheel cannot be
fitted with snow chains.IMPORTANT
14)Contact a dedicated Alfa Romeo
Dealership as soon as possible to have the
correct tightening of the wheel stud bolts
checked.
15)When turning the jack handle make
sure that it can turn freely without scraping
your hand against the ground. The moving
components of the jack ("worm screw" and
joints) can also cause injuries: avoid
touching them. If you come into contact
with lubricating grease, clean yourself
thoroughly.
CHANGING A BULB
16)
106) 107) 108)
GENERAL
INSTRUCTIONS
Before changing a bulb check the
contacts for oxidation;
replace blown bulbs with others of
the same type and power;
after replacing a headlight bulb,
always check its alignment;
when a light is not working, check
that the corresponding fuse is intact
before changing the bulb. For the
location of fuses, refer to the paragraph
“If a fuse blows” in this chapter.
IMPORTANT When the weather is cold
or damp or after heavy rain or washing,
the surface of headlights or rear lights,
may steam up and/or form drops of
condensation on the inside. This is a
natural phenomenon due to the
difference in temperature and humidity
between the inside and the outside of
the glass which does not indicate a
fault and does not compromise the
normal operation of lighting devices.
The mist disappears quickly when the
lights are turned on, starting from the
centre of the diffuser, extending
progressively towards the edges.
112
IN AN EMERGENCY

IMPORTANT
16)Halogen bulbs must be handled
holding the metallic part only. Touching the
transparent part of the bulb with your
fingers may reduce the intensity of the
emitted light and even reduce the lifespan
of the bulb. In the event of accidental
contact, wipe the bulb with a cloth
moistened with alcohol and let the bulb dry.
WARNING
106)Modifications or repairs to the electric
system that are not carried out properly or
do not take the system technical
specifications into account can cause
malfunctions leading to the risk of fire.
107)Halogen bulbs contain pressurised
gas, in the case of breakage they may
burst causing glass fragments to be
projected outwards.
108)Due to the high power supply voltage,
gas discharge bulbs (Bi-Xenon) should only
be replaced by specialised personnel:
danger of death! Contact a dedicated Alfa
Romeo Dealership.
113

Bulbs Type Power Ref. Figure
Front side lights/Daytime running lights (DRL) LED - -
Rear side lights LED - -
Dipped/Main beam headlights (versions with Bi-Halogen
headlights) (for versions/markets, where provided)H7 55 W D
Dipped/Main beam headlights (versions with Bi-Xenon
headlights) (for versions/markets, where provided)D1S 35 W -
Dipped/Main beam headlights (versions with Bi-LED
headlights) (for versions/markets, where provided)LED - -
Front direction indicators PY21W 21 W B
Rear direction indicators PY21W 21 W B
Side direction indicators WY5W 5 W A
Brake lights LED - -
3rd brake light LED - -
Number plate lights W5W 5 W A
Rear fog light W16W 16 W A
Reversing light W16W 16 W A
Roof light C10W 10 W C
Luggage compartment light W5W 5 W A
115

REPLACING
EXTERIOR BULBS
FRONT LIGHT CLUSTERS
These contain the bulbs for the side
lights/daytime running lights (DRL),
dipped beam headlights, main beam
headlights and direction indicators. The
bulbs are arranged as follows fig. 98:
To replace the bulbs for the dipped and
main beam headlights and for the
direction indicators open the
corresponding protective flaps on the
inner wheel arch fig. 99 that can be
located by steering the wheel
completely.
A - direction indicator bulb protective
flapB - dipped/main beam headlight bulb
protective flap
Side lights/daytime
running lights (DRL)
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
DIPPED/MAIN BEAMS
To replace the bulb, proceed as follows:steer the wheel completely;
open the protective flap B fig. 99 by
rotating the fixing screw;
take out the electric connector A
fig. 100 and then rotate the bulb holder
B clockwise and remove it;
extract the bulb and replace it;
refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;
close the protective flap B fig. 99.
Direction indicators
Front
To change the bulb, proceed as follows:
steer the wheel completely;
open the protective flap A fig. 99 by
rotating the fixing screw;
take out the electric connector A
fig. 101 and then rotate the bulb holder
B clockwise and remove it;
98A0L0091
99A0L0092
100A0L0093
116
IN AN EMERGENCY
ASide lights/daytime running lights
BDipped/main beam headlights
CDirection indicators

extract the bulb and replace it;
refit the new bulb, making sure that it
is locked correctly, and reconnect the
connector A;
close the protective flap A fig. 99.
Side
To change the bulb, proceed as follows:
adjust the lens A in the point shown
in figure fig. 102 to compress the
retaining clip B, then pull the cluster
outwards;
turn the bulb holder B anticlockwise,
extract the bulb and replace it;
refit the bulb holder B in the lens and
turn it clockwise;
refit the cluster making sure that the
internal clip clicks into position.
REAR LIGHT CLUSTERS
These contain the bulbs for the side
lights, direction indicators and brake
lights.
Direction indicators
To change the bulb, proceed as follows:remove the protective cap A
fig. 103 (one for each side) on the side
cover of the luggage compartment.
remove the second protective cap in
rubber B fig. 104 inserting the hand
inside the hole.
rotate the bulb holder and extract it;
replace the bulb by pressing it and
turning it anticlockwise;
refit the previously removed
protective caps.
Side lights/brake lights
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
101A0L0094102A0L0095103A0L0096
104A0L0134
117

REAR FOG LIGHT/
REVERSING LIGHT
109)
To replace the rear fog light bulbs A
fig. 105 or the reversing lights B
fig. 105 proceed as follows:
turn the bulb holder C
fig. 106 anticlockwise, extract the bulb
and replace it.
3rd BRAKE LIGHTS
These are LEDs. For the replacement,
contact the dedicated Alfa Romeo
Dealership.
NUMBER PLATE LIGHTS
To replace the bulbs proceed as
follows:
adjust the lens A in the point shown
in figure fig. 107 laterally to compress
the retaining clip, then pull the number
plate light cluster A out;
turn bulb holder B
fig. 108 anticlockwise, extract bulb C
and replace it.
WARNING
109)The rear fog light and the reversing
light are located close to the exhaust pipes;
take the utmost care not to get burnt
during the bulb replacement.
105A0L0097
106A0L0126107A0L0136
108A0L0099
118
IN AN EMERGENCY

INTERIOR BULB
REPLACEMENT
ROOF LIGHT
To change the bulb, proceed as follows:remove roof light A fig. 109 working
at the points indicated by the arrows;
open protective flap B fig. 110 andreplace bulb C, releasing it from the
side contacts. Make sure that the new
bulb is correctly secured between the
contacts;
reclose protective flap B fig. 110 and
fix roof light A fig. 109 in its housing,
making sure that it is locked.
LUGGAGE
COMPARTMENT ROOF
LIGHT
To replace the bulb, proceed as follows:
open the luggage compartment and
extract roof light A fig. 111, working in
the point shown by the arrow;
open protection B and replace the
press-fitted bulb;
reclose protection B on the lens;
refit roof light A by inserting it in its
correct position, firstly on one side and
then pressing on the other side until it
clicks into place.
109A0L0100
110A0L0101
111A0L0140
119

ENGINE COMPARTMENT FUSE BOXfig. 114
DEVICE PROTECTEDFUSE AMPERE
Headlight beam switch (for versions/markets, where provided) F09 5
Single tone hornF10 10
12 V socket / cigar lighter F86 15
External mirror defrosters F88 7.5
DASHBOARD FUSE BOXfig. 116
DEVICE PROTECTEDFUSE AMPERE
Central lockingF38 15
Two-way windscreen washer pump F43 20
+30 Driver side electric windows F47 20
+30 Passenger side electric windows F48 20
WARNING
110)If a fuse blows again, contact a dedicated Alfa Romeo Dealership.
111)Never replace a fuse with another with a higher amp rating; DANGER OF FIRE.
112)If a general protective fuse (MAXI-FUSE, MEGA-FUSE, MIDI-FUSE) blows, contact a dedicated Alfa Romeo Dealership.
113)Before replacing a fuse, make sure that the ignition key has been removed and that all the other services are switched off and/or
disengaged.
114)Contact a dedicated Alfa Romeo Dealership if a safety system (airbags, brakes), transmission system (engine, gearbox) or steering
system general protection fuse blows.
122
IN AN EMERGENCY