2016 Alfa Romeo 4C lock

ENGINE COMPARTMENT FUSE BOXfig. 114
DEVICE PROTECTEDFUSE AMPERE
Headlight beam switch (for versions/markets, where provided) F09 5
Single tone hornF10 10
12 V socket / cigar lighter F86 15
External mirror defrosters F88 7.5
DASHBOARD FUSE BOXfig. 116
DEVICE PROTECTEDFUSE AMPERE
Central lockingF38 15
Two-way windscreen washer pump F43 20
+30 Driver side electric windows F47 20
+30 Passenger side electric windows F48 20
WARNING
110)If a fuse blows again, contact a dedicated Alfa Romeo Dealership.
111)Never replace a fuse with another with a higher amp rating; DANGER OF FIRE.
112)If a general protective fuse (MAXI-FUSE, MEGA-FUSE, MIDI-FUSE) blows, contact a dedicated Alfa Romeo Dealership.
113)Before replacing a fuse, make sure that the ignition key has been removed and that all the other services are switched off and/or
disengaged.
114)Contact a dedicated Alfa Romeo Dealership if a safety system (airbags, brakes), transmission system (engine, gearbox) or steering
system general protection fuse blows.
122
IN AN EMERGENCY

IMPORTANT
19)Be careful to position the lift arms
correctly at the points illustrated, in order to
prevent damage to the carbon fibre chassis
and the bodywork components.
20)To avoid damage to the carbon fibre
chassis, the car cannot be raised with
standard hydraulic jacks, only with suitable
lowered hydraulic jacks. Contact a
dedicated Alfa Romeo Dealership.
TOWING THE CAR
21)
The tow hook provided with the car is
located in the tool box in the luggage
compartment.
ATTACHING THE TOW
HOOK
Take tow hook A and tighten it fully onto
the threaded pin fig. 120.
115) 116) 117)
IMPORTANT
21)The tow hook attachment is only
available at the front end of the car.
WARNING
115)Before towing, turn the key to MAR
and then to STOP without extracting it. The
steering column will automatically lock
when the key is removed and the wheels
cannot be steered. Also check that the
transmission is in neutral (N)
116)When towing, remember that the
assistance of the brake servo is absent.
Consequently, more force is required at the
pedal in order to brake. Do not use flexible
cables when towing and avoid jerky
movements. Make sure not to damage
parts in contact with the car while towing.
When towing the vehicle, you must comply
with all specific traffic regulations and
adopt an appropriate driving behaviour. Do
not start the engine while towing the car.
Before tightening the ring, clean the
threaded housing thoroughly. Make sure
that the ring is fully screwed into the
housing before towing the car.
117)The tow hook must be used
exclusively for roadside assistance
operations. You are allowed to tow the
vehicle for short distances using an
appropriate device in accordance with the
highway code (a rigid bar), to move the
vehicle on the road in readiness for towing
or transport via a tow truck. Tow hooks
MUST NOT be used to tow vehicles off the
road or where there are obstacles and/or
for towing operations using cables or other
non-rigid devices. In compliance with the
above conditions, towing must take place
with the two vehicles (one towing, the other
towed) aligned as much as possible along
the same centre line.
120A0L0107
125

SCHEDULED SERVICING PLAN
1750 Turbo Petrol VERSIONS
Thousands of kilometres 20 40 60 80 100 120
Months 12 24 36 48 60 72
Check battery charge status and recharge if necessary●●●●●●
Check tyre conditions/wear and adjust pressure, if required●●●●●●
Check operation of lighting system (headlights, direction
indicators, hazard warning lights, luggage compartment,
passenger compartment, glove compartment, instrument panel
warning lights, etc.)
●●●●●●
Check vehicle fastenings●●●
Check mechanical components fastenings●●●●●●
Check operation of windscreen wiper/washer system and adjust
jets, if necessary●●●●●●
Check position/wear of windscreen wiper blade●●●●●●
Check cleanliness of boot lock, cleanliness and lubrication of
linkages●●●●●●
Visually inspect condition of: exterior bodywork, carbon
monocoque, aerodynamic bottom, pipes and hoses (exhaust, fuel
supply system, brakes), rubber elements (boots, driveshaft boots,
sleeves, bushes, etc.)
●●●●●●
Check condition and wear of front brake pads and discs, and
operation of pad wear indicator●●●●●●
128
SERVICING AND MAINTENANCE

PERIODIC CHECKS
Every 1,000 km or before long journeys,
check and, if necessary, top up the
following:
engine coolant level;
brake fluid;
screen washer fluid;
tyre inflation pressure and condition;
operation of lighting system
(headlamps, direction indicators, hazard
warning lights, etc.);
operation of screen washing/wiping
system and positioning/wear of wiper
blade.
Every 3,000 km, check and top up if
required: engine oil level.
HEAVY-DUTY USE OF
THE CAR
If the car is used mainly under one of
the following conditions:
if the car is used under demanding
conditions, e.g. on track;
dusty roads;
short, repeated journeys (less than
7–8 km) at sub-zero outside
temperatures;
engine often idling or driving long
distances at low speeds or long periods
of inactivity;
the following checks must be carried
out more often than indicated in the
Scheduled Servicing Plan:
check of front and rear disc brake
pad condition and wear;
check cleanliness of tailgate locks,
cleanliness and lubrication of linkage;
visually inspect conditions of: engine,
gearbox, transmission, pipes and hoses
(exhaust - fuel system - brakes) and
rubber elements (boots - sleeves -
bushes - etc.);
check battery charge and battery
fluid level (electrolyte);
visually inspect condition of the
accessory drive belts;
check and, if necessary, change
engine oil and replace oil filter;
check and, if necessary, replace air
cleaner.
Using the car on track should beregarded as an exception. The car has
been designed and produced for road
use.
131

after the check, reinsert the plug B
with the control pipe C in the initial
position;
reposition the engine cover grille and
tighten the 4 self-tapping screws A.
WARNING Re-close the plug holding it
horizontally (not directed towards the
engine cover) to prevent the opening
tang from remaining locked in a position
difficult to reach.
It is recommended to check the
windscreen washer fluid regularly, in
particular in driving conditions needing
a heavier use of the windscreen washer.
If the level is not sufficient, namely if
there is no fluid inside the pipe, proceed
as follows:
to avoid any interference during the
procedure, lift the windscreen wiper
blade according to the "Windscreen
wiper" paragraph in the "Maintenance
and care" chapter;
loosen the 4 self-tapping screws A
fig. 124 using the supplied screwdriver.
Remove the engine cover grille;
take the white funnel D fig. 127 fortopping up the windscreen washer
fluid/fuel and its extension pipe from the
service kit in the luggage compartment;
take out the plug B fig. 125 with the
fluid control pipe through the engine
cover opening on the grille;
introduce the funnel D fig. 127 and
its extension pipe in the reservoir neck
and top up;
after topping up, remove the funnel
D with the extension pipe;
refit the plug B with the dipstick;
reposition the engine cover grille and
tighten the 4 self-tapping screws A.
BRAKE FLUID
125) 126)
26) 27)
To check the brake fluid level, proceed
as follows:
loosen the 2 self-tapping screws E
125A0L0131
126A0L0147
127A0L0148
135

Replacing the
windscreen wiper blade
Proceed as follows:lift the windscreen wiper blade,
following the instructions given
preciously;
press tab A fig. 133 of the
attachment spring and remove the
blade from the arm;
fit the new blade, inserting the tab in
the dedicated housing in the arm and
checking that it is locked;
lower the wiper arm onto the
windscreen.
NOZZLES
Screen washer
The windscreen washer nozzles are
adjustable fig. 134. They are originally
adjusted at the factory. Should it be
necessary to adjust them again,
contact a dedicated Alfa RomeoDealership.
If there is no jet of fluid, firstly check that
there is some fluid in the reservoir (see
paragraph "Checking fluid levels" in this
chapter).
Then check that the nozzle holes are
not clogged; use a needle to unblock
them if necessary.
WARNING
136)Driving with a worn wiper blade is a
serious hazard, because visibility is
reduced in bad weather.
IMPORTANT
29)Do not operate the screen wiper with
the blades lifted from the windscreen.
BODYWORK
PROTECTION AGAINST
ATMOSPHERIC AGENTS
The car features advanced
technological solutions for effective
protection of the exterior bodywork and
structure.
The best products and best painting
systems lend the exterior bodywork
particularly high resistance to
atmospheric agents (solar radiation,
acid rain, etc.) and gravel, through
specific protections.
The chassis too, in light,
corrosion-resistant alloy, is treated to
prevent the formation of surface
oxidation.
CAR CORROSION
WARRANTY
Your car is covered by warranty against
perforation, due to rust, of any original
element of the structure. For the
general terms of this warranty, refer to
the Warranty Booklet.
PRESERVING THE
BODYWORK
Paintwork5)30)
Touch up abrasions and scratches
immediately.
Maintenance of paintwork consists of
washing the car: the frequency
depends on the conditions and
environment where the car is used. For
example, in highly polluted areas, or if
133A0L0086
134A0L0087
141
31)

BODYWORK PAINT
IDENTIFICATION PLATE
It is applied under the tailgate and
shows the following data fig. 139:
APaint manufacturer.
BColour name.
CColour code.
DRespray and touch up colour code.
ENGINE MARKING
This is stamped on the cylinder block
and includes the type and the engine
serial number.
139A0L0090
147

REFUELLING
1750 Turbo Petrol
Prescribed fuels / Original fluids and
lubricants
litres kg
Fuel tank 40 -
Unleaded petrol not less than 95 RON (EN
228 specification)
including a reserve of 4 - 5 -
Engine cooling system 10.6 9.4Mixture of distilled water and PARAFLU
fluid
UP
50%(*)
Engine sump 5.4 4.6
SELENIA SPORT POWER
Engine sump and filter 5.8 5.0
Gearbox casing/differential: 1.88 1.6 TUTELA TRANSMISSION GEARTECH
Transmission hydraulic activation system 1.45 1.2 TUTELA CS SPEED
Hydraulic brake circuit with ABS (Anti-lock
braking system)0.52 0.56 TUTELA TOP 4
Windscreen washer fluid reservoir 1.9 1.7Mixture of water and TUTELA
PROFESSIONAL SC 35
(*) When the vehicle is used in particularly harsh weather conditions, we recommend using a 60-40 mixture of PARAFLUUPand demineralised water.
162
TECHNICAL SPECIFICATIONS