2016 Alfa Romeo 4C warning lights

Warning lights on
displayWhat it means What to do
amberEXTERIOR LIGHTS FAILURE
The symbol and corresponding message appear on the
display if a fault is detected in one of the following lights:
daytime running lights (DRL)
side lights
dipped beam headlights
direction indicators
rear fog lights
reversing lights
number plate lights.
The fault relating to these lights may be caused by: one
or more blown fuses, one or more blown bulbs or a
broken electrical connection.Check, and if necessary replace the fuses involved, in
accordance with the "Fuse replacement" paragraph in
the "In an emergency" chapter; if this does not resolve
the fault, check, and if necessary replace, the bulbs
involved, in accordance with the "External bulb
replacement" paragraph in the "In an emergency"
chapter.
Should this operation also fail to resolve the fault,
contact the dedicated Alfa Romeo Dealership, for a
comprehensive check of the electrical system.
amberSERVICE (SCHEDULED SERVICING)
The digital warning light
is automatically displayed,
along with a dedicated message, with key at MAR,
2,000 km (or equivalent value in miles) before the
following scheduled servicing interval and is activated
again every 200 km (or equivalent value in miles).Contact a dedicated Alfa Romeo Dealership. The
operations in the “Scheduled Servicing Plan” will be
performed and the message will be reset.
79

Warning lights on
displayWhat it means What to do
GENERAL FAILURE
(for versions/markets, where provided)
The symbol lights up in the display in the circumstances
indicated below.
Engine oil pressure sensor failure
The symbol lights up when the engine oil pressure
sensor is faulty. The display shows the dedicated
message.In this case contact a dedicated Alfa Romeo Dealership
to have the fault fixed as soon as possible.
Clutch overheating message
The
symbol, together with a message on the display,
lights up to indicate clutch overheating.
If the driver continues, thesymbol will switch
off and the
warning light will light up (on some
versions together with a message on the display)
to indicate a transmission failure.
If thesymbol lights up along with a message on the
display, reduce gear shifting and/or change usage
conditions, until the normal operating conditions are
restored.
If the
warning light lights up (a message will appear
on the display, on some versions) stop immediately,
operate the handbrake, switch off the engine and wait 5
minutes: after this, normal transmission operating
conditions will be restored.
Should the transmission failure condition persist,
contact the dedicated Alfa Romeo Dealership
FUEL CUT-OFF
The symbol and the corresponding message are shown
on the display in the following cases:
fuel cut-off system intervention: the yellow
symbol lights up;
fuel cut-off system failure: the red symbol
lights up.
For the fuel cut-off system reactivation procedure, refer
to the "Fuel Cut-Off System" section of the "Controls"
paragraph, in the "Knowing your car" chapter. If it is still
not possible to restore the fuel supply, contact a
dedicated Alfa Romeo Dealership.
80
KNOWING THE INSTRUMENT PANEL

Warning lights on
displayWhat it means What to do
LUGGAGE COMPARTMENT OPEN
The symbol and the corresponding message are shown
on the display.
POSSIBLE ICE ON ROAD
The symbol and corresponding message appear on the
display when the outside temperature is below or equal
to 3°C.
IMPORTANT In the event of outside temperature sensor
failure, the digits that indicate the value are replaced by
dashes.
BRAKE LIGHT FAILURE
The symbol and corresponding message appear on the
display if a fault is detected in the brake lights.The fault may be caused by a blown bulb, a blown
protection fuse or an interruption of the electrical
connection.
PARKING SENSOR FAILURE
The symbol and corresponding message appear on the
display if there is a parking sensor failure.
DISPLAY OF SELECTED DRIVING MODE (“Alfa DNA”
system)
A letter (d, n, or a) corresponding to the active driving
mode (dynamic or race, normal, all weather) and a
dedicated message are shown on the display.
81

suitable power and torque for the
acceleration requested by the driver.
When implementing the "Kick Down"
function, the system ensures varying
transmission management in
accordance with the selected DNA
mode.
LEVERS ON THE
STEERING WHEEL
These enable sequential gear shifting
fig. 79.
– steering wheel stalk "+(pulling stalk
towards driver, see fig. 80 ): engage
higher gear;
– steering wheel stalk "–(pulling stalk
towards driver, see fig. 80 ): engage
lower gear.The engagement of a lower (or higher)
gear is only permitted if the engine rpm
allow it.
STARTING THE CAR
To start the engine press the brake
pedal: the system engages neutral (N)
automatically.
After the starting procedure, 1st gear (
1) or reverse (R) can be engaged.
Irrespective of the mode selected (
AUTO/MANUAL), to engage 1st gear
or reverse (R), it is necessary to press
the brake pedal and press the1button
on the transmission control panel (or
the "+" steering wheel stalk) to engage
1st gear or theRbutton to engage
reverse.
When 1st gear is engaged, the system
sets itself toAUTOmode.
Neutral (N) can be engaged again by
pressing theNbutton with the brake
pedal pressed.When the1,NorRbuttons are
pressed (or "+" steering wheel stalk is
operated) without pressing the brake
pedal, no gear change request is
implemented by the system.
IMPORTANT Reverse cannot be
engaged by pressing the "-" stalk on
the steering wheel.
Important information
If starting is requested with a
transmission failure (see "Warning lights
and messages" paragraph), carry out
the “Delayed start-up” procedure: when
the key is turned to AVV for at least 7
seconds with brake pedal pressed, the
engine will be started. The system will
remain in “recovery” condition.
If the engine does not start, contact a
dedicated Alfa Romeo Dealership.
When the driver's door is opened, the
system activates the hydraulic
components so that they are prepared
for the subsequent engine starting.
MOVING THE CAR
The car can set off both in 1st gear and
reverse (R).
Notes (concerning car start-up)
The gears can only be engaged by
pressing the brake pedal. If the brake
pedal is not depressed, the display will
show a dedicated message.
It is not possible to set off in a higher
gear than 1st: if this is attempted, the
display shows a dedicated message.
79A0L0071
80A0L0072
98
STARTING AND DRIVING

WARNING
89)The Launch control function is only
available in Race mode. Regardless of
what is explicitly indicated in the
description of these modes, the ESC and
ASR systems are deactivated during
operation of the Launch Control function.
This means that vehicle dynamic control is
the sole responsibility of the driver.
Therefore pay the utmost attention when
using the Launch Control. Take into
account traffic and road surface conditions
and during manoeuvres make sure there is
enough room in the area concerned.
SAVING FUEL
Alfa Romeo has designed and built the
vehicle using technologies, materials
and devices able to reduce negative
environmental impact. Here are some
suggestions to further contribute to
environmental protection.
GENERAL
CONSIDERATIONS
Car maintenance
Have checks and adjustments carried
out in accordance with the “Scheduled
Servicing Plan”.
Tyres
Check the tyre pressures at least once
every four weeks: if the pressure is too
low, consumption levels increase as
resistance to rolling is higher.
Climate control system
The use of the climate control system
leads to higher fuel consumption. If the
temperature outside permits, try to use
ventilation only.
DRIVING STYLE
Starting
Do not warm the engine with the car at
a standstill or at idle or high speed:
under these conditions the engine
warms up much more slowly, increasing
consumption and emissions. It is
therefore advisable to move off
immediately, slowly, avoiding high
speeds: in this way the engine will
warm up more quickly.Unnecessary actions
Avoid accelerating when stopped at
traffic lights or before switching off the
engine. This action is absolutely
pointless and only increases
consumption and pollution.
Gear selection
Using a low gear for faster acceleration
increases consumption.
In the same way, improper use of a high
gear increases consumption, emissions
and engine wear.
Max. speed
Fuel consumption increases
considerably with speed. Maintain a
constant speed, avoiding unnecessary
braking and acceleration, which cost in
terms of both fuel consumption and
emissions.
Acceleration
Accelerating violently will greatly affect
consumption and emissions: avoid
frequent and strong accelerations.
CONDITIONS OF USE
Cold starting
Short journeys and frequent cold starts
do not allow the engine to reach
optimum operating temperature.
This results in a significant increase in
consumption levels (from +15 to +30%
on the urban cycle) and emissions.
101

Traffic and road conditions
Rather high consumption levels are
linked to situations with heavy traffic, for
instance when travelling in queues with
frequent use of the lower gears or in
cities with many traffic lights.
Stops in traffic
During prolonged hold-ups (e.g. level
crossings) the engine should be
switched off.SNOW TYRES
Use snow tyres of the same size as the
normal tyres provided with the car: the
dedicated Alfa Romeo Dealership will
be able to advise you on the most
appropriate tyre to use.
Only use these tyres in the event of ice
or snow on the roads. In these
conditions it is recommended to select
the "All Weather" mode of the Alfa DNA
system.
For the type of tyre to be used, inflation
pressures and the specifications of
snow tyres, follow the instructions given
in the "Wheels" paragraph in the
"Technical specifications" chapter.
90)
The performance of these tyres on
low-grip surfaces are reduced
considerably when the tread depth is
below 4 mm. They should be replaced
in this case.
Due to the specific characteristics of
snow tyres, in normal weather
conditions and dry asphalt or on long
motorway journeys, the performance of
these tyres is lower than that of
standard tyres. Their usage should
therefore be restricted in accordance
with their type approval.
IMPORTANT When using snow tyres
with a maximum speed index below the
one that can be reached by the car
(increased by 5%), place a notice in the
passenger compartment, plainly in view,
which states the maximum speedallowed by the snow tyres (as per EC
Directive).
All four tyres should be the same brand
to ensure greater safety when driving
and braking as well as making the car
more responsive. It is inadvisable to
change the rotation direction of tyres.
Refer to the "Raising the car" section in
the "In an emergency" chapter for
further details on how to raise the car
correctly.
WARNING
90)The maximum speed for snow tyres
marked “Q” is 160 km/h, while it is
190 km/h for “T” tyres and 210 km/h for
"H" tyres. The highway code speed limits
must however always be complied with.
102
STARTING AND DRIVING

WARNING
92)Indicate the presence of the stationary
car in accordance with current regulations:
hazard warning lights, warning triangle, etc.
Those on board should get out of the
vehicle and wait for the wheel to be
repaired away from the threat posed by the
traffic. If parked on a slope or rough
surface, chock the wheels with wedges or
other suitable devices (for the correct
procedure for parking the car safely, refer
to the "Parking" paragraph in the "Starting
and driving" chapter).
93)Give the booklet to the technicians who
will be handling the tyre that was treated
using the "Fix&Go Automatic" kit.
94)A repair is not possible if the wheel rim
is damaged (groove is deformed, causing
air to escape). Do not remove foreign
bodies (screws or nails) from the tyre.95)Never operate the compressor for
longer than 20 consecutive minutes. Risk
of overheating. The kit is not suitable for
definitive repairs, so the repaired tyres may
only be used temporarily.
96)As required by current regulations, the
information on chemical substances for the
protection of human health and the
environment and on the safe use of the
sealing fluid are on the packaging label.
Compliance with the indications on the
label is an essential condition to ensure the
safety and the effectiveness of the product.
Remember to carefully read the label
before use; the user of the product is
responsible for any damages caused by
improper use. The sealing fluid has an
expiry date. Replace the bottle if the
sealant has expired.
97)Wear the protective gloves provided
with the kit.
98)Apply the adhesive label where it can
be easily seen by the driver as a reminder
that the tyre has been treated with the
quick repair kit. Drive carefully, especially
on corners. Do not exceed 80 km/h. Avoid
sudden acceleration or braking.
99)If the pressure has fallen below 1.8 bar,
do not drive any further: the Fix&Go
Automatic quick tyre repair kit cannot
guarantee the correct hold because the
tyre is too damaged. Contact a dedicated
Alfa Romeo Dealership.
100)Always indicate that the tyre was
repaired using the quick tyre repair kit. Give
the leaflet to the personnel charged with
handling the tyre treated with the tyre
repair kit.
IMPORTANT
13)In the event of a puncture caused by
foreign bodies, the kit may be used to
repair tyres showing damage on the tread
or shoulder up to max. 4 mm diameter. Do
not use the repair kit if the tyre was
damaged as a result of being used when
underinflated.
IMPORTANT
2)Dispose of the bottle and the sealant
liquid properly. Have them disposed of in
compliance with national and local
regulations.
88A0L0082
108
IN AN EMERGENCY

make sure the contact surfaces
between space-saver wheel and hub
are clean and free from impurities so
that the fixing stud bolts will not come
loose;
fit the space-saver wheel and tighten
the first stud bolt for a few turns into the
lowest hole. Tighten the remaining stud
bolts in the same way.
take the spanner A fig. 90 and fully
tighten the fixing studs;
operate the suitable tool E to lower
the car. Then extract the jack;
use the spanner A and check all stud
bolts are fully tightened in a criss-cross
fashion as per the numerical sequence
illustrated in fig. 97;
WARNING While replacing the wheel it
is advisable to place it upside down,
with the aesthetic part facing upward,
so as not to damage the alloy rim.
REFITTING THE WHEEL
Following the procedure described
previously, raise the car and remove the
space-saver wheel.
Proceed as follows:
make sure the contact surfaces
between standard wheel and hub are
clean and free from impurities so that
the fixing stud bolts will not come loose;
tighten the retaining stud bolts using
spanner A fig. 90;
lower the car and remove the jack;
use spanner A to fully tighten the
stud bolts, following the sequence
illustrated in fig. 97
.................................. 0
At the end of the operation
Proceed as follows:
reposition the space-saver wheel;
insert the jack and the other tools in
the container;
arrange the container and tools in the
luggage compartment;
WARNING
101)The space-saver wheel (for
versions/markets where provided) is
specific to your car, do not use it on other
models, or use the space-saver wheel of
other models on your car. The space-saver
wheel must only be used in the event of an
emergency. Never use it for more than
strictly necessary and never exceed
80 km/h. On the space-saver wheel there
is an orange label, summarising the main
warnings regarding space-saver wheel
usage restrictions. Never remove or cover
the label. The label contains the following
indications in four languages: "Warning! For
temporary use only! 80 km/h max! Replace
with standard wheel as soon as possible.
Never cover this indication."
102)Alert other drivers that the car is
stationary in compliance with local
regulations: hazard warning lights, warning
triangle, etc. Any passengers on board
should leave the car, especially if it is
heavily laden. Passengers should stay
away from on-coming traffic while the
wheel is being changed. On hills or uneven
roads, use chocks or appropriate objects
to block the wheels of the vehicle.
97A0L0187
111