2015 YAMAHA XT660Z wheel bolts

PERIODIC MAINTENANCE AND ADJUSTMENT
6-29
6
EAU23292
Checking the wheel bearingsThe front and rear wheel bearings must
be checked at the intervals specified in
the periodic maintenance and lubrica-
tion chart. If there is play in the wheel
hub or if the wheel does not turn
smoothly, have a Yamaha dealer
check the wheel bearings.
EAUS1913
BatteryTo access the battery (XTZ660Z):
The battery is located under the seat.
(See page 3-16.)
Remove the battery bracket by remov-
ing the bolts.
Battery (XTZ660ZA):
The battery is located under the fuel
tank.Have a Yamaha dealer access the bat-
tery.
These models are equipped with a
VRLA (Valve Regulated Lead Acid) bat-
tery. There is no need to check the
electrolyte or to add distilled water.
However, the battery lead connections
need to be checked and, if necessary,
tightened.
WARNING
EWA10761
Electrolyte is poisonous and
dangerous since it contains sul-
furic acid, which causes severe
burns. Avoid any contact with
skin, eyes or clothing and al-
ways shield your eyes when
1. Positive battery terminal
2. Holder
3. Bolt
4. Negative battery terminal
1. Battery
U2BDE1E0.book Page 29 Tuesday, December 16, 2014 5:38 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-36
6
EAU44792
Front wheel (for non-ABS
models)
WARNING
EWA14841
For the ABS model, have a Yamaha
dealer remove and install the wheel.
EAU56480
To remove the front wheel
WARNING
EWA10822
To avoid injury, securely support the
vehicle so there is no danger of it
falling over.1. Loosen the front wheel axle pinch
bolts, the wheel axle and the
brake caliper bolts.2. Lift the front wheel off the ground
according to the procedure in the
previous section “Supporting the
motorcycle”.
3. Remove the brake caliper on each
side by removing the bolts.
NOTICE: Do not apply the brake
after the brake calipers have
been removed, otherwise the
brake pads will be forced shut.
[ECA11052]
4. Pull the wheel axle out, and then
remove the wheel.To install the front wheel
1. Lift the wheel up between the fork
legs.
2. Insert the wheel axle.
3. Install the brake calipers by install-
ing the bolts.
TIPMake sure that there is enough space
between the brake pads before install-
ing the brake calipers onto the brake
discs.4. Lower the front wheel so that it is
on the ground.
5. Tighten the wheel axle and the
brake caliper bolts to the specified
torques.NOTICE
ECAB0062
Be sure the right brake disc is posi-
tioned exactly between the brake
pads to prevent any brake drag. Tap
the side of the right fork leg to posi-
tion the disc correctly.6. Tighten wheel axle pinch bolt A,
and then pinch bolt B to their
specified torque.
1. Wheel axle
2. Brake caliper bolt
3. Front wheel axle pinch boltZAUM1266
U2BDE1E0.book Page 36 Tuesday, December 16, 2014 5:38 PM

PERIODIC MAINTENANCE AND ADJUSTMENT
6-37
6 7. Retighten pinch bolt A to the
specified torque.
8. Apply the brake lever several
times, and then while holding the
brake lever in, push down hard on
the handlebar several times to
check for proper fork operation.
EAU44802
Rear wheel (for non-ABS
models)
WARNING
EWA14841
For the ABS model, have a Yamaha
dealer remove and install the wheel.
EAU56711
To remove the rear wheel
WARNING
EWA10822
To avoid injury, securely support the
vehicle so there is no danger of it
falling over.1. Loosen the axle nut.2. Lift the rear wheel off the ground
according to the procedure on
page 6-35.
3. Remove the axle nut.
4. Fully loosen the locknut on each
side of the swingarm.
5. Turn the drive chain slack adjust-
ing bolts fully in direction (a) and
push the wheel forward.
Tightening torques:
Wheel axle:
59 Nm
Front wheel axle pinch bolt:
18 Nm
Brake caliper bolt:
40 Nm
1. Wheel axle nut
2. Drive chain slack adjusting bolt
3. Locknut
4. Drive chainZAUM1267
U2BDE1E0.book Page 37 Tuesday, December 16, 2014 5:38 PM