2015 VOLKSWAGEN TOUAREG jump start terminals

x Vigorously shake the tire inflation cylinder ⇒ fig. 343 (10) a few times back and forth.
x Tightly screw the filling hose ⇒ fig. 343 (3) to the tire inflation bottle (turn clockwise). The foil on the seal is automatically pierced.
x Remove the sealing plug from the filling hose ⇒ fig. 343 (3) and slide the open end onto the tire valve.
x Hold the cylinder with the bottom pointing up and fill the entire contents of the tire inflation cylinder into the tire.
x Detach the empty tire inflation cylinder from the valve.
x Using the valve core wrench ⇒ fig. 343 (1) screw the valve core back into the tire valve.
Inflating the tire
x Screw the tire inflation hose ⇒ fig. 343 (5) of the air compressor tightly to the tire valve.
x Check whether the air release valve ⇒ fig. 343 (7) is screwed on tightly.
x Open the engine hood ⇒  Working in the engine compartment.
x Attach the cable clips ⇒ fig. 343 (9) only to the jump-start terminals in the engine compartment
⇒ fig. 344. The red clip on the compressor cable is connected to the positive (+) terminal; the black clip is connected to the negative terminal (—).
x Start the vehicle engine and let it run.
x Switch the air compressor on using the ON / OFF switch ⇒ fig. 343 (8),
x Let the air compressor run until a pressure of 36 – 44 psi (250 - 300 kPa) is reached ⇒ . Maxi-
mum run time 8 minutes ⇒ .
x Switch off the air compressor.
x If an air pressure of 36 – 44 psi (250 - 300 kPa) cannot be reached, unscrew the tire inflation hose from the tire valve.
x Drive about 30 feet (10 meters) backwards or forwards so that the sealant can be distributed inside the tire.
x Connect the tire inflation hose of the air compressor again to the tire valve and repeat the inflation process.
x If the required tire pressure still cannot be reached, the tire is too badly damaged. The tire cannot
be sealed using the tire mobility set. Do not drive the vehicle. Get professional assistance ⇒ .
x Disconnect the air compressor and unscrew the tire inflation hose from the tire valve.
x If a tire pressure of 36 – 44 psi (250 – 300 kPa) is reached, continue driving right away and drive at a speed of not more than 50 mph (80 km/h).
x Check tire pressure after 10 minutes of driving ⇒  Check after 10 minutes of driving.
WARNING
The tire inflation hose and air compressor can get hot during inflation.
x Protect hands and skin from hot parts.
x Do not place the hot tire inflation hose or hot air compressor on flammable material.
x Let the equipment cool off almost completely before stowing it.
x If the tire cannot be inflated to at least 36 psi (250 kPa), the damage is too great to be re-paired with the tire mobility set. The sealant is not able to seal the tire. Do not drive the vehi-cle. Get professional assistance.

WARNING
Improper use of jumper cables when jump-starting a vehicle with a dead battery can cause the battery to explode, leading to serious personal injury. To help reduce the risk of battery explosion:
x All work on the batteries or the electrical system in your vehicle can cause serious acid burns, fires, or electrical shocks. Always read and heed the following WARNINGS and safety
precautions before working on the batteries or the electrical system ⇒  12 Volt vehicle bat-tery.
x Always make sure that the battery providing starting assistance (the booster battery) has the same voltage as the dead battery (12 V) and about the same amperage capacity (see bat-tery label).
x Never jump-start a vehicle with a thawed or frozen battery. The battery can explode. A dead battery can freeze at temperatures around +32 °F (0 °C).
x A battery that is frozen or was frozen, but has since thawed, must be replaced.
x When the vehicle battery is jump-started, it gives off hydrogen gas, which is highly explo-sive! Always keep fire, sparks, open flame, and smoking materials far away from vehicle bat-teries. Never use a cellular telephone while connecting or disconnecting jumper cables.
x Jump-start batteries only in well-ventilated areas. Batteries give off highly explosive hy-drogen gas during jump-starting.
x Always route the jumper cables so that they cannot get caught in any moving parts in the engine compartment.
x Never short out the battery terminals by connecting the positive terminal (+) and negative (–) terminals with each other.
x Never connect the negative cable from the other vehicle directly to the negative terminal of the dead battery, as this may cause the hydrogen gas given off by the dead battery to ex-plode.
x Never attach the negative cable from the vehicle providing starting assistance to any part of the fuel system or to the brake hoses or brake lines.
x Never allow the non-insulated parts of the battery clamps to touch.
x Never allow the jumper cable attached to the positive battery terminal to contact metal parts of the vehicle.
x Always follow the instructions of the jumper cable manufacturer.
NOTICE
To help prevent extensive damage to the vehicle electrical system, read and heed the follow-ing:
x Connecting jumper cables improperly can cause a short circuit and do expensive damage to the vehicle's electrical system.
x Do not let the vehicles touch each other while the jumper cables are connected. If they do, electrical current may flow between the vehicles when the positive (+) terminals are connected, causing electrical system damage.

Positive and negative jump-starting terminals

Fig. 349 In the engine compartment: Positive jump-start terminal + and negative jump-start terminal -.

The procedure for attaching and for removing the jumper cables is described below. Perform each of the following steps only in the order in which it is described.
Before you begin
d Switch off the ignition in both vehicles.
d Open the hoods of both vehicles.
d Remove the cover from the positive terminal on your vehicle and, if necessary, the battery cover of the other vehicle.
Diagram A: Attaching jumper cables
Diagram A applies where the vehicle with the dead battery has jump-start terminals (1) and is being
jump-started by a vehicle whose battery is in the engine compartment (2) ⇒ .
1. Attach one end of the red jumper cable to the positive jump-start terminal (+) of the vehicle with the dead battery (1).
2. Attach the other end of the red jumper cable to the positive terminal (+) of the booster battery (2).
3. Connect one end of the black jumper cable to a suitable ground connection (3) on the vehicle with the booster battery (2). A suitable ground connection is a solid metal part bolted directly to the en-gine block of the vehicle with the booster battery or this vehicle's engine block itself.
4. Attach the other end of the black jumper cable to the negative jump-start terminal (-) of the vehicle with the dead battery (1).
Diagram B: Attaching jumper cables
Diagram B applies where the dead battery (1) is in the engine compartment of the vehicle being jump-
started, and the vehicle providing starting assistance has jump-start terminals (2) ⇒ .
1. Attach one end of the red jumper cable to the positive terminal (+) of the dead battery (1).
2. Attach the other end of the red jumper cable to the positive jump-start terminal (+) of the vehicle providing starting assistance (2).
3. Attach one end of the black jumper cable to the negative jump-start terminal (-) of the vehicle providing starting assistance (2).
4. Connect the other end of the black jumper cable to a suitable ground connection (3) on the vehicle with the dead battery (1). A suitable ground connection is a solid metal part bolted directly to the engine block of the vehicle with the dead battery or this vehicle's engine block itself.
Diagram C: Attaching jumper cables where both vehicles have jump-start terminals
Diagram C applies where the vehicle with the dead battery has jump-start terminals (1) and is being
jump-started by a vehicle that also has jump-start terminals (2) ⇒ .
1. Attach one end of the red jumper cable to the positive jump-start terminal (+) of the vehicle with the dead battery (1).
2. Attach the other end of the red jumper cable to the positive jump-start terminal (+) of the vehicle providing starting assistance (2).
3. Attach one end of the black jumper cable to the negative jump-start terminal (-) of the vehicle providing starting assistance (2).
4. Attach the other end of the black jumper cable to the negative jump-start terminal (-) of the vehicle with the dead battery (1).
Starting the engine
1. Start the engine of the vehicle with the good battery that is providing help and let it run at idle speed.

WARNING
Improper use of jumper cables when jump-starting a vehicle with a dead battery can cause the battery to explode, leading to serious personal injury. To help reduce the risk of battery explosion:
x All work on the batteries or the electrical system in your vehicle can cause serious acid burns, fires, or electrical shocks. Always read and heed the following WARNINGS and safety
precautions before working on the batteries or the electrical system ⇒  12 Volt vehicle bat-tery.
x Always wear proper eye protection. Never lean over the vehicle batteries.
x Attach the jumper cables in the correct order: first the positive cable, then the negative cable.
x Never connect the negative cable from the vehicle providing starting assistance to parts of the fuel system or to the brake hoses or brake lines.
x Never allow the non-insulated parts of the battery clamps to touch.
x Never allow the jumper cable attached to the positive battery terminal to contact metal parts of the vehicle.
x Specialized knowledge and tools are required to access the vehicle battery. For this rea-son, have an authorized Volkswagen dealer or an authorized Volkswagen Service Facility check the electrolyte level of the vehicle battery.
x Avoid electrostatic discharge in the vicinity of the vehicle battery. Sparks may cause the hydrogen gas escaping from the vehicle battery to ignite.
x Never jump-start a vehicle with a battery that is damaged or frozen or that was frozen and has thawed. The battery can explode. Replace the battery instead.
x Always follow the instructions of the jumper cable manufacturer.
x Always make sure that the battery providing starting assistance has the same voltage as the dead battery (12 V) and about the same capacity (see battery label).
x Batteries give off explosive hydrogen gas. Always keep fire, sparks, open flame and smok-ing materials away from batteries.
x Never connect the negative cable from the other vehicle directly to the negative terminal of the dead battery. The hydrogen gas from the battery is explosive.
x Never short out the battery terminals by connecting the positive (+) and negative (–) ter-minals with each other.
NOTICE
Checking the electrolyte level
x The 12 Volt vehicle battery is located under the left front seat. Specialized knowledge and tools are required to access the vehicle battery. For this reason, have an authorized Volkswagen dealer or an authorized Volkswagen Service Facility check the electrolyte level of the vehicle battery.