Please carry out each step only in the order specified:
3. Using both hands, simultaneously press and hold both the
HomeLink button you want to program ( 1 , 2 , or 3 ) and the hand-
held transmitter button, as shown ⇒ fig. 34. Do not release the
buttons until the HomeLink indicator light flashes slowly and
then rapidly. When the indicator light flashes rapidly, release both
buttons. The rapid flashing indicates successful programming.
4.
Press and hold the programmed HomeLink button and watch the
indicator light.
If the indicator light comes on and does not flash, programming is
complete and your garage door opener or other device should acti-
vate when the HomeLink button is pressed and released.
If the indicator light blinks rapidly for 2 seconds and then stays on,
proceed with the following programming instructions for a rolling
code device. A second person may make the following steps
quicker and easier. Please use a ladder or other device. Do not
stand on your vehicle to perform the next steps ⇒ in Operating
the HomeLink® Universal Transmitter.
5.
At the garage door opener receiver (overhead unit) in the garage,
locate the “learn” or “training” button. The name and color of the
button may vary by manufacturer. This button is usually located
near the hanging antenna wire attachment point on the unit. If you
cannot locate the “training” button, refer to the garage door open-
er’s user manual.
6. Press and release the “training” button.
Once the button is pressed, you have 30 seconds to initiate
the next step.
7. Return to the vehicle. Firmly press and hold the programmed
HomeLink button for 2 seconds and release.
8. Repeat the “press/hold/release” sequence up to 3 times to com-
plete the programming process for that button.
Repeat the steps to program the other buttons for the HomeLink® Universal Transmitter on the sun visor keypad to control other devices.
Removing the front head restraints
x Sit in the back seat behind the head restraint you want to remove. Pull the head restraint all the
way up ⇒ in Adjusting the front and rear head restraints. Recline the backrest with the head re-straint so that there is enough overhead clearance to remove it.
x Slide a flat object, such as a plastic credit card, underneath the right side of the cap on the right-
hand seat guide rod ⇒ fig. 40 (1) to unlock the head restraint.
x Push the flat object (plastic card) in against the guide rod to depress a release button located under the cap (not visible).
x Use one hand to hold the release button in with the flat object. With your other hand, lift the same guide rod slightly to expose a notch in the rod at the bottom (can be seen and felt with fingers). The right-hand guide rod is now released.
x To release the left-hand guide rod, press button (2) in (towards guide rod) and hold.
x Pull the head restraint out completely while holding button (2).
Installing the front head restraints
x Position head restraint properly over the head restraint guides of the respective seat backrest and insert the head restraint into the guides.
x Push the head restraint down while pressing button (2).
x Adjust the head restraint according to the occupant's size ⇒ Adjusting the front and rear head restraints.
Removing the rear head restraint
x Unlock the backrest of the rear seat bench and fold it forward ⇒ Luggage compartment.
x Pull the head restraint all the way up ⇒ .
x If necessary, press the flat blade of the screwdriver from the vehicle tool kit into the slit of the trim
cap ⇒ fig. 41 (1) in the direction of the arrow and hold it in this position.
x At the same time press button (2) while a second person pulls out the head restraint completely.
x Fold the backrest of the rear seat bench back so that it locks securely.
Reinstalling the rear head restraint
x Unlock the backrest of the rear seat bench and fold it forward ⇒ Luggage compartment.
x Position head restraint properly over the head restraint guides of the respective seat backrest and insert the head restraint into the guides.
x Push the head restraint down while pressing button (2).
x Fold the backrest of the rear seat bench back so that it locks securely.
x Adjust the head restraint according to the occupant's size ⇒ Adjusting the front and rear head restraints.
WARNING
Driving without head restraints or with improperly adjusted head restraints increases the risk of serious injuries in a collision.
x Always drive with the head restraints in place and properly adjusted to help minimize the risk of neck injury in a crash.
x Always reinstall head restraints as soon as possible so that vehicle occupants are proper-ly protected.
