2015 SUZUKI NEXA tow
[x] Cancel search: towPage 88 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
/ L J K W L Q J 2 S H U D W L R Q
60MK011
To turn the lights on or off, twist the knob
on the end of the lever. There are three
positions:
2 ) )
All lights are off.
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
Front position lights, tail lights, license
plate light, instrument lights and headlights
are on.
60MK012
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
$ X W R P D W L F / L J K W V 2 S H U D W L R Q
L I H T X L S S H G
64MS059
64MS060
Your vehicle’s lighting system is controlled
by two main systems: the Lighting switch
and the Auto-On Headlight System (when
the lighting switch is in the “AUTO” posi-
tion).
The two systems work together to operate
your lights as shown in the following chart:
(3)
(2)
(1)
( ; $ 0 3 / (
( ; $ 0 3 / (
(3)(4)
(2) (1)
( ; $ 0 3 / (
(5)
Page 90 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
To turn the lights on or off, twist the knob
on the end of the lever. There are four
positions:
2 ) )
All lights are off.
$ 8 7 2
This function works when it on mode has
been changed to ON by pressing the
engine switch. The headlights and position
lights are turned on and off automatically
according to the amount of outside light
detected by a sensor. They go out auto-
matically when you change the ignition
mode to “ACC” or “LOCK” (OFF) by press-
ing the engine switch.
The light sensor (5) for sensing the amount
of outside light is installed on the upper
part of the windshield. It also serves as the
rain sensor for the rain-sensing wipers.NOTE:
• Avoid covering the light sensor area of
the windshield with a sticker. The sticker
may impair the performance of the sen-
sor and make the system unable to con-
trol operation of the lights correctly.
• If you changed the ignition mode to ON
by pressing the engine switch and the
“AUTO” position remains selected, the
headlights and position lights come on
automatically as the outside gets dark
even with the engine not running. Leav-
ing the lights lit for a long time may lead
to a completely discharged battery.
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
Front position lights, tail lights, license
plate light, instrument lights and headlights
are on.
64MS061
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
$ X W R R Q K H D G O L J K W V \ V W H P
64MS062
The Auto-on headlight system automati-
cally turns on all lights that are operated by
the lighting control lever on the steering
column, when the following three condi-
tions are all met.
Conditions for Auto-on headlight system
operation:
1) It is dark around the light sensor (5).
2) The lighting control lever is in the
“AUTO” position.
3) You press the engine switch to change
the ignition mode to ON.
& $ 8 7 , 2 1
, I W K H O L J K W V H Q V R U D U H D R I W K H Z L Q G
V K L H O G L V F R Y H U H G Z L W K P X G L F H R U
R W K H U V L P L O D U V X E V W D Q F H V W K H K H D G
O L J K W V D Q G S R V L W L R Q O L J K W V P D \ E H
W X U Q H G R Q H Y H Q Z K H Q L W L V V W L O O O L J K W
R X W V L G H % H I R U H U H P R Y L Q J V X F K V X E
V W D Q F H V I U R P W K H Z L Q G V K L H O G D O Z D \ V
V H W W K H Z L S H U F R Q W U R O O H Y H U W R W K H
Page 96 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
5 H S U R J U D P P L Q J W K H U D L Q V H Q V L Q J Z L S H U
I X Q F W L R QThe “AUTO” position operation of the rain-
sensing wiper function can be customized
to your preference by reprogramming its
setting as follows. Please contact an D X W K R U L V H G 0 D U X W L 6 X ] X N L Z R U N V K R S
for
this customization. ) X O O D X W R P D W L F Z L S L Q J I D F W R U \ V H W W L Q J
The system automatically selects the most
appropriate of the following wiping modes:
no wiping, intermittent wiping, low-speed
wiping, and high-speed wiping.
6 H P L D X W R P D W L F Z L S L Q J
The system automatically selects the most
appropriate of the following wiping modes:
intermittent wiping, low-speed wiping, or
high-speed wiping. (The wipers do not stop
automatically.)
, Q W H U P L W W H Q W Z L S L Q J
The wipers operate only in the intermittent
wiping mode. The wiping interval can be
changed with the knob on the control lever.
: L Q G V K L H O G : D V K H U
64MS067
To spray windshield washer fluid, pull the
lever toward you. The windshield wipers
will automatically turn on at low speed if
they are not already on and the “INT” posi-
tion is equipped.
: $ 5 1 , 1 *
Page 108 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
– The remote controller is in stowage
like the glove box or a door pocket.
– The remote controller is in the sun
visor pocket or on the floor.
• Even when the remote controller is out-
side the “interior workable” area, if it is in
any of the following conditions, you may
be able to start the engine or select the
ignition mode. The “remote controller
outside” warning may not be given at
that time.
– The remote controller is outside the
vehicle but very close to a door.
– The remote controller is on the instru-
ment panel.
3 D U N L Q J % U D N H / H Y H U
64MS185
(1) To set
(2) To release
(3) To release
The parking brake lever is located between
the seats. To set the parking brake, hold
the brake pedal down and pull the parking
brake lever all the way up. To release the
parking brake, hold the brake pedal down,
pull up slightly on the parking brake lever,
push the button on the end of the lever
with your thumb, and lower the lever to its
original position.
(2)
(3) (1)
( ; $ 0 3 / (
: $ 5 1 , 1 *
Page 122 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
6 H W 6 H Q V R U VYou can select either the normal or trailer
mode of the parking sensor via the informa-
tion display. Refer to “Information Display”
in the “BEFORE DRIVING” section.
1 R U P D O P R G H
All sensors operate. Use this mode under
normal conditions.
7 U D L O H U P R G H
The rear corner and rear center sensors are
inhibited from operating. Use this mode
when towing a trailer.
NOTICE
0 D N H V X U H W K H Q R U P D O P R G H L V
V H O H F W H G Z L W K W K H S D U N L Q J V H Q V R U
Z K H Q V W H H U L Q J W K H Y H K L F O H L Q W R D
J D U D J H , I W K H S D U N L Q J V H Q V R U L V O H I W L Q
W K H W U D L O H U P R G H W K H U H D U F R U Q H U D Q G
U H D U F H Q W H U V H Q V R U V D U H Q R W I X Q F W L R Q
L Q J
: D U Q L Q J D Q G , Q G L F D W R U 0 H V V D J H VIf there is a problem or warning regarding the parking sensor system, a message is dis-
played on the information display in the instrument cluster, and a symbol blinks and the
buzzer sounds. If a message is displayed, follow its instruction.
0 H V V D J H 6 \ P E R O % X ] ] H U 3 U R E D E O H F D X V H D Q G U H P H G \
Two blinking
lines in a sen-
sor location.Series of
double
beepsThere may be problem with the
parking sensor system.
Have your vehicle inspected by
an D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S.
One blinking
line in a sensor
location.Series of
single
beepsThe indicated sensor is contami-
nated.
Wipe it clean with a soft cloth.
Page 133 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
' U L Y L Q J R Q 6 O L S S H U \ 5 R D G V
60G089A
Under wet road conditions you should
drive at a lower speed than on dry roads
due to possible slippage of tires during
braking. When driving on icy, snow-cov-
ered, or muddy roads, reduce your speed
and avoid sudden acceleration, abrupt
braking, or sharp steering movements.
7 L U H & K D L Q VTire chains should only be used if they are
needed to increase traction or are required
by law. Make sure that the chains you use
are the correct size for your vehicle’s tires.
Also make sure that there is enough clear-
ance between the fenders and the chains
as installed on the tires.
Install the chains on the front tires tightly,
according to the chain manufacturer’s
instructions. Retighten the chains after
driving about 1.0 km (1/2 mile) if neces-
sary. With the chains installed, drive slowly.
, I < R X U 9 H K L F O H * H W V 6 W X F NIf your vehicle gets stuck in snow, mud, or
sand, follow the directions below:
1) Shift the transaxle back and forth
between first gear and reverse. This will
create a rocking motion which may give
you enough momentum to free the
vehicle. Press gently on the accelerator
to keep wheel spinning to a minimum
wheel rpm. Remove your foot from the
accelerator while shifting.
Do not race the engine. Excessive
wheel spin will cause the tires to dig
deeper, making it more difficult to free
the vehicle.
2)
If your vehicle remains stuck after a few
minutes of rocking, we recommend you
to consult your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S or a roadside assistance
service. If a towing service is not
available in an emergency, your
vehicle may be tem-porarily towed by
a towing cable or chain secured to
the towing hook either on the front of
the vehicle or on the rear of the vehicle.
Refer to “Frame Hooks” in the
“OTHER CONTROLS AND
EQUIPMENT” section.
NOTICE
Page 148 of 288
Downloaded from www.Manualslib.com manuals search engine 2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
* O R Y H % R [
64MS120
To open the glove box, pull the latch lever.
To close it, push the lid until it latches
securely.
64MS148
The glove box light (if equipped) stays on
while the lid is open.
2 Y H U K H D G & R Q V R O H
L I H T X L S S H G
64MS121
Use this stowage to keep small articles.
You can open the lid (1) by pressing the
raised portion on it.
: $ 5 1 , 1 *
1 H Y H U G U L Y H Z L W K W K H J O R Y H E R [ O L G
R S H Q , W F R X O G F D X V H L Q M X U \ L I D Q D F F L
G H Q W R F F X U V ( ; $ 0 3 / (
EXAMPLE(1)
( ; $ 0 3 / (
Page 151 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
) U R Q W % R W W O H + R O G H U
5 H D U % R W W O H + R O G H U You should hold a bottle with a cap in the
holder. ) U R Q W $ U P U H V W Z L W K & R Q V R O H % R [
L I H T X L S S H G
61MM0B029
The armrest can be slid forward.
& R Q V R O H E R [
Use this stowage for keeping small items.
Open the compartment by raising the top
lid while keeping the lever (1) up.
61MM0B030
NOTE:
Always close the lid after you put something
into or take something out of the box.
$ 8 ; 8 6 % V R F N H W L I H T X L S S H G
64MS082
The AUX/USB socket is provided in the
console box.
Connect your portable digital music player,
etc. to this socket to enjoy music through
the vehicle’s audio system using it as a
source. Refer to “Audio System” in this
section.
NOTICE
7 R D Y R L G G D P D J H W R W K H D U P U H V W G R
Q R W O H D Q R Q L W R U D O O R Z D F K L O G W R V L W R Q
L W ( ; $ 0 3 / (
( ; $ 0 3 / (
(1)
(1)
NOTICE
' R Q R W S O D F H D Q \ R E M H F W V L Q F R Q V R O H
E R [ Z K L F K P D \ V S L O O Z D W H U R U O L T X L G
6 S L O O L Q J R I O L T X L G R Q $ 8 ; 8 6 % V R F N H W
F D Q F D X V H G D P D J H P D O I X Q F W L R Q R I
$ 8 ; 8 6 % V R F N H W
( ; $ 0 3 / (