2015 SUZUKI NEXA steering wheel
[x] Cancel search: steering wheelPage 133 of 288
Downloaded from www.Manualslib.com manuals search engine
' 5 , 9 , 1 * 7 , 3 6
0 6 (
' U L Y L Q J R Q 6 O L S S H U \ 5 R D G V
60G089A
Under wet road conditions you should
drive at a lower speed than on dry roads
due to possible slippage of tires during
braking. When driving on icy, snow-cov-
ered, or muddy roads, reduce your speed
and avoid sudden acceleration, abrupt
braking, or sharp steering movements.
7 L U H & K D L Q VTire chains should only be used if they are
needed to increase traction or are required
by law. Make sure that the chains you use
are the correct size for your vehicle’s tires.
Also make sure that there is enough clear-
ance between the fenders and the chains
as installed on the tires.
Install the chains on the front tires tightly,
according to the chain manufacturer’s
instructions. Retighten the chains after
driving about 1.0 km (1/2 mile) if neces-
sary. With the chains installed, drive slowly.
, I < R X U 9 H K L F O H * H W V 6 W X F NIf your vehicle gets stuck in snow, mud, or
sand, follow the directions below:
1) Shift the transaxle back and forth
between first gear and reverse. This will
create a rocking motion which may give
you enough momentum to free the
vehicle. Press gently on the accelerator
to keep wheel spinning to a minimum
wheel rpm. Remove your foot from the
accelerator while shifting.
Do not race the engine. Excessive
wheel spin will cause the tires to dig
deeper, making it more difficult to free
the vehicle.
2)
If your vehicle remains stuck after a few
minutes of rocking, we recommend you
to consult your D X W K R U L V H G 0 D U X W L 6 X ] X N L
Z R U N V K R S or a roadside assistance
service. If a towing service is not
available in an emergency, your
vehicle may be tem-porarily towed by
a towing cable or chain secured to
the towing hook either on the front of
the vehicle or on the rear of the vehicle.
Refer to “Frame Hooks” in the
“OTHER CONTROLS AND
EQUIPMENT” section.
NOTICE
Page 169 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
• To return the blower speed selector (2),
air intake selector (3), and “MODE”
switch (4) to automatic operation, push
the “AUTO” switch (8).
64MS149
Be careful not to cover the interior tem-
perature sensor (10) located between the
steering wheel and the climate control
panel, or the solar sensor (11) located at
the top of the central part of the dash-
board. These sensors are used by the
automatic system to regulate temperature.
0 D Q X D O R S H U D W L R Q
You can manually control the climate con-
trol system. Set the selectors to the
desired positions.
64MS091
NOTE:
If you need maximum defrosting:
• push the defrost switch (5) to turn on the
defroster (the air conditioning system will
come on and the fresh air position (b)
will be selected automatically),
• set the blower speed selector to HIGH,
• adjust the temperature selector to the
“HI” indication on the display, and
• adjust the side outlets so the air blows
on the side windows.
0 D L Q W H Q D Q F HIf you do not use the air conditioner for a
long period, such as during winter, it may
not give the best performance when you
start using it again. To help maintain opti-
mum performance and durability of your air
conditioner, it needs to be run periodically.
Operate the air conditioner at least once a
month for one minute with the engine
idling. This circulates the refrigerant and oil
and helps protect the internal components.
If your air conditioner is equipped with air
filters, clean or replace them as specified
in the “Maintenance Schedule” in the
Page 205 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
' H O H W L R Q R I D X G L R G H Y L F H L Q I R U P D W L R Q
' H O H W H $ X G L R
Follow the instructions below to delete the
registered information of audio device.
1) Press the Bluetooth
® setup button (6).
The Bluetooth
® setup menu will be dis-
played.
2) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Setup Blue-
tooth”, and press the knob (2) to deter-
mine the selection.
3) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “List Audio”,
and press the knob (2) to determine the
selection.
4) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select an audio
device to be deleted, and press the
knob (2) to determine the selection.
5) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Delete”, and
press the knob (2) to determine the
selection.
6) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Delete?”,
and press the knob (2) to determine the
selection.
7) Turn the TUNE FOLDER PUSH
SOUND knob (2) to select “Confirm”,
and press the knob (2) to complete the
deletion.
NOTE:
When selecting “Go Back”, the previous
menu will be displayed.
' L V F O D L P H U I R U % O X H W R R W K
Š I X Q F W L R Q
• Depending on the mobile phone models,
some phones may not be compatible
fully or partially (some function may be
restricted).
• Connectivity or voice quality may get
affected depending on circumstances.
• After the ignition switch is turned to the
“ON” position, the audio system takes
few seconds to detect and connect to
the Bluetooth
® device (if already paired)
• Make sure that you are aware of all
applicable lock laws and accordingly use
Bluetooth
Š device.
5 H P R W H $ X G L R & R Q W U R O V
L I H T X L S S H G Controlling of basic functions of the audio
system is available using the switches on
the steering wheel. $ G M X V W L Q J W K H Y R O X P H
• To increase the volume, hold down “+” of
the VOL switch (1). The volume will keep
on being increased until the switch is
released.
• To decrease the volume, hold down “-” of
the VOL switch (1). The volume will keep
on being decreased until the switch is
released.
• To mute the sound, press the switch (2). 6 H O H F W L Q J W K H P R G HPress the switch (3).
Each time the button is pressed, the mode
will change as follows:
(2)
(3)
(1)
(4)
Page 209 of 288
Downloaded from www.Manualslib.com manuals search engine
2 7 + ( 5 & 2 1 7 5 2 / 6 $ 1 ' ( 4 8 , 3 0 ( 1 7
0 6 (
% D W W H U \ , Q V W D O O D W L R QInstall a lithium battery (CR2025) with the poles facing the correct direction.
% D W W H U \ U H S O D F H P H Q W W L P L Q J
• When battery power is depleted, the button may not be operable. If the remote controller
does not operate, replace the battery and check the operation.
& D X W L R Q R Q E D W W H U \
• Be sure to follow the instructions to prevent battery leakage, over-heating, ignition or
explosion.
If battery leakage has occurred, wipe the
container first then install a new battery. If
the battery solution contacts the skin, wash
off with water completely.
& D X W L R Q R Q 5 H P R W H & R Q W U R O O H U• Do not leave the remote controller in an
area exposed to direct sunlight, such as
on the dashboard or steering wheel. The
remote controller may deform because of
the heat, (Be especially careful of the
dashboard exposed to direct sunlight in
the summer, as it will become extremely
hot).
: $ 5 1 , 1 *
Page 227 of 288
Downloaded from www.Manualslib.com manuals search engine 7-4
INSPECTION AND MAINTENANCE
64MS0-74E
Interval: This interval should be judged by odometer reading
or months, whichever comes first.
FREE INSPECTION
PERIODIC MAINTENANCE AT COST
km (x1000)
1
5
10
20
30
40
50
60
70
80
months
1
6
12
24
36
48
60
72
84
96
5-5.
Brake drum and shoes (Wear)
-
-
I
I
I
I
I
I
I
I
5-6.Master cylinder and wheel cylinder or caliper, brake hoses and pipes (Fluid
leakage, damage)IIIIIIIIII
5-7.
Master cylinder sub assembly, wheel cylinder boot kit & caliper seal set
I
I
I
I
I
R
I
I
I
R
WHEEL
6-1.
Tyres (air pressure, abnormal wear, crack and rotation)
I
I&O
I&O
I&O
I&O
I&O
I&O
I&O
I&O
I&O
6-2. Wheels (Damage) I I I IIIIIII
6-3.
Front/Rear wheel bearing (Loose, damage)
I
I
I
I
I
I
I
I
I
I
FRONT / REAR SUSPENSION
7-1.
Suspension strut (Oil leakage, damage)
I
I
I
I
I
I
I
I
I
I
7-2. Suspension arms / Knuckle support (Loose, damage) – I I I I I I I I I
7-3.
Rear spring (Damage)
I
I
I
I
I
I
I
I
I
I
7-4.Shock absorbers (Oil leakage, damage) I I I I IIIIII
7-5.
All bolts and nuts (Loose)
–
T
T
T
T
T
T
T
T
T
7-6.Torsion rods – I I I I I I I I I
STEERING
8-1.
Steering wheel (Play, loose)
I
I
I
I
I
I
I
I
I
I
8-2.Steering column and tie rods (Loose, damage, wear) I I I I I I I I I I
ELECTRICAL
9-1.
Battery electrolyte (Level, leakage)
I
I
I
I
I
I
I
I
I
I
9-2. Wiring harness connection (Loose, damage) – I I I I I I I I I
9-3.
Lighting system (Operation, stains, damage)
I
I
I
I
I
I
I
I
I
I
9-4.Horn (Operation) IIIIII I II I
9-5.
System Voltage
)
I
I
I
I
I
I
I
I
I
BODY
10-1.
All chassis bolts and nuts (Tighten)
–
I
T
T
T
T
T
T
T
T
10-2. All latches, hinges and locks (Function)) I I&L I&L I&L I&L I&L I&L I&L I&L I&L
Page 251 of 288
Downloaded from www.Manualslib.com manuals search engine
, 1 6 3 ( & 7 , 2 1 $ 1 ' 0 $ , 1 7 ( 1 $ 1 & (
0 6 (
) U R Q W ) R J / L J K W L I H T X L S S H G 1) Start the engine. Turn the steering wheel
to rotate the tires to the opposite side of
the fog light that requires replacement.
Then turn off the engine.
61MM0B079
2) Remove the screws (1).
61MM0B080
3) Remove the clips (2) by prying it off with
a flat blade screwdriver as shown in the
illustration.
61MM0B081
4) Open the end of the cover inside the
fender.
80JM071
5) Disconnect the coupler by pushing the
lock release. Turn the bulb holder coun-
terclockwise and remove it.
(1)
( ; $ 0 3 / (
(2)
( ; $ 0 3 / ( ( ; $ 0 3 / (
( ; $ 0 3 / (
Page 269 of 288
Downloaded from www.Manualslib.com manuals search engine
( 0 ( 5 * ( 1 & < 6 ( 5 9 , & (
0 6 (
4) If the booster battery you are using is fit-
ted to another vehicle, start the engine of
the vehicle with the booster battery. Run
the engine at moderate speed.5) Start the engine of the vehicle with the
flat battery.
6) Remove the jump leads in the exact
reverse order in which you connected
them.
7 R Z L Q JIf you need to have your vehicle towed,
contact a professional service. Your dealer
can provide you with detailed towing
instructions.
: K H H O ' U L Y H : ' 0 D Q X D O 7 U D Q
V D [ O HManual transaxle vehicles may be towed
using either of the following methods.
1) From the front, with the front wheels
lifted and the rear wheels on the ground.
Before towing, make sure that the park-
ing brake is released.
2) From the rear, with the rear wheels lifted
and the front wheels on the ground, pro-
vided the steering and drivetrain are in
operational condition. Before towing,
make sure that transaxle is in neutral,
the steering wheel is unlocked (vehicle
without keyless push start system - the
ignition key should be in the “ACC” posi-
tion) (vehicle with keyless push start sys-
tem - the ignition mode is ACC), and the
steering wheel is secured with a clamp-
ing device designed for towing service.
& $ 8 7 , 2 1
& R Q Q H F W W K H M X P S O H D G W R W K H H Q J L Q H
P R X Q W E U D F N H W V H F X U H O \ , I W K H M X P S
O H D G G L V F R Q Q H F W V I U R P W K H H Q J L Q H
P R X Q W E U D F N H W E H F D X V H R I Y L E U D W L R Q D W
W K H V W D U W R I W K H H Q J L Q H W K H M X P S O H D G
F R X O G E H F D X J K W L Q W K H G U L Y H E H O W V
NOTICE
2 E V H U Y H W K H I R O O R Z L Q J L Q V W U X F W L R Q V
Z K H Q W R Z L Q J \ R X U Y H K L F O H