2015 SUZUKI NEXA sensor
[x] Cancel search: sensorPage 90 of 288
Downloaded from www.Manualslib.com manuals search engine % ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
To turn the lights on or off, twist the knob
on the end of the lever. There are four
positions:
2 ) )
All lights are off.
$ 8 7 2
This function works when it on mode has
been changed to ON by pressing the
engine switch. The headlights and position
lights are turned on and off automatically
according to the amount of outside light
detected by a sensor. They go out auto-
matically when you change the ignition
mode to “ACC” or “LOCK” (OFF) by press-
ing the engine switch.
The light sensor (5) for sensing the amount
of outside light is installed on the upper
part of the windshield. It also serves as the
rain sensor for the rain-sensing wipers.NOTE:
• Avoid covering the light sensor area of
the windshield with a sticker. The sticker
may impair the performance of the sen-
sor and make the system unable to con-
trol operation of the lights correctly.
• If you changed the ignition mode to ON
by pressing the engine switch and the
“AUTO” position remains selected, the
headlights and position lights come on
automatically as the outside gets dark
even with the engine not running. Leav-
ing the lights lit for a long time may lead
to a completely discharged battery.
Front position lights, tail lights, license
plate light and instrument lights are on, but
headlights are off.
Front position lights, tail lights, license
plate light, instrument lights and headlights
are on.
64MS061
With the headlights on, push the lever for-
ward to switch to the high beams (main
beams) or pull the lever toward you to
switch to the low beams. When the high
beams (main beams) are on, a light on the
instrument panel will come on. To momen-
tarily activate the high beams (main
beams) as a passing signal, pull the lever
slightly toward you and release it when you
have completed the signal.
$ X W R R Q K H D G O L J K W V \ V W H P
64MS062
The Auto-on headlight system automati-
cally turns on all lights that are operated by
the lighting control lever on the steering
column, when the following three condi-
tions are all met.
Conditions for Auto-on headlight system
operation:
1) It is dark around the light sensor (5).
2) The lighting control lever is in the
“AUTO” position.
3) You press the engine switch to change
the ignition mode to ON.
& $ 8 7 , 2 1
, I W K H O L J K W V H Q V R U D U H D R I W K H Z L Q G
V K L H O G L V F R Y H U H G Z L W K P X G L F H R U
R W K H U V L P L O D U V X E V W D Q F H V W K H K H D G
O L J K W V D Q G S R V L W L R Q O L J K W V P D \ E H
W X U Q H G R Q H Y H Q Z K H Q L W L V V W L O O O L J K W
R X W V L G H % H I R U H U H P R Y L Q J V X F K V X E
V W D Q F H V I U R P W K H Z L Q G V K L H O G D O Z D \ V
V H W W K H Z L S H U F R Q W U R O O H Y H U W R W K H
Page 91 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
This system is operated by a signal from the
light sensor (5) on the front windshield. Do
not cover the sensor (5). If you do, the sys-
tem will not work correctly.NOTE:
The light sensor is sensitive to infrared
rays, so it may operate incorrectly in the
region of strong infrared rays.
5 H S U R J U D P P L Q J W K H D X W R P D W L F O L J K W
I X Q F W L R Q
The following settings of the automatic
light function can be customized to your
preference. Please contact an D X W K R U L V H G
0 D U X W L 6 X ] X N L Z R U N V K R S if you want the
function reprogrammed.
6 H Q V L W L Y L W \ R I W K H O L J K W V H Q V R U
The amount of outside light needed to turn
the lights on and off is pre-set at the fac-
tory. The sensitivity of the light sensor can
be adjusted so that the lights are turned on
and off when it is:
• lighter outside than the pre-set condition,
or
• darker outside than the pre-set condition 5 D L Q W U L J J H U H G D X W R P D W L F O L J K W L Q J R S H U
D W L R Q
The setting of the auto-on headlight sys-
tem can be changed to make it turn on the
headlights:
• when the rain sensor senses heavy rain-
fall
• when the rain sensor senses light and
heavy rainfall (in coordination with rain-
sensing wiper operation), or
• independently from rain-sensing wiper
operation. / L J K W 5 H P L Q G H U % X ] ] H UThe interior buzzer continuously beeps if
you open the driver’s door without turning
off the headlights and position lights. This
function is triggered under the following
condition:
The headlights and/or position lights are on
even after the ignition switch is turned off, or
the engine switch is pressed to change the
ignition mode to LOCK (OFF).
The buzzer stops sounding when you turn
off the headlights and position lights.NOTE:A message is indicated on the information
display in the instrument cluster while the
buzzer is sounding.
) U R Q W ) R J / L J K W 6 Z L W F K
L I H T X L S S H G
64J058
The front fog light comes on when the fog
light switch is pushed in with the position
lights, tail lights and/or the headlights are
on. An indicator light above the switch will
be lit when the front fog light is on.
NOTE:
In some countries the lighting operation
may be different from the above descrip-
tion according to local regulations.
: $ 5 1 , 1 *
, W W D N H V D E R X W V H F R Q G V I R U W K H O L J K W
V H Q V R U W R U H D F W W R D F K D Q J H L Q O L J K W L Q J
F R Q G L W L R Q V 7 R K H O S D Y R L G D Q D F F L G H Q W
G X H W R U H G X F H G Y L V L E L O L W \ W X U Q R Q \ R X U
K H D G O L J K W V E H I R U H G U L Y L Q J L Q W R D W X Q Q H O
S D U N L Q J V W U X F W X U H R U W K H O L N H
Page 95 of 288
Downloaded from www.Manualslib.com manuals search engine
% ( ) 2 5 ( ' 5 , 9 , 1 *
0 6 (
64MS066
If the control lever has on “AUTO” position,
you can change the system’s sensitivity to
rain/snow by turning the knob of the control
lever forward for increased sensitivity or
rearward for decreased sensitivity.
61M0219
(1) Rain sensorNOTE:
• Under the following conditions, the rain
sensor may not be able to sense rain or
snow correctly, and thus the rain-sensing
wiper function may not work or may work
incorrectly. (Use a position other than
“AUTO” under these conditions.)
– Rain or snow does not hit the rain sen-
sor area of the windshield, or the snow
is not of a type that is able to be
detected by the sensor.
– The rain sensor area is covered with
mud, ice or other similar substance.
You should remove any foreign sub-
stance.– There were already raindrops on the
windshield before starting rain-sensing
wiper operation. You should remove
the raindrops by operating the wipers
under manual control.
– The rain sensor is hotter than 80°C
(176°F) in the sun or lower than –10°C
(14°F) in freezing weather. (The wip-
ers do not operate under this condi-
tion.)
– The windshield is coated with a water-
repellent substance, which causes
raindrops to run down quickly. This will
give a clearer view and the wipers
may seem to operate too frequently. In
this case, decrease the system’s sen-
sitivity.
– The sensor area is covered with a
sticker.
– The wiper blades are damaged. You
should replace them.
•
The following conditions may indicate
problems with the rain-sensing wiper
system. If your system exhibits any of
the following conditions, have it
inspected by an D X W K R U L V H G 0 D U X W L
6 X ] X N L Z R U N V K R S.
– Rainfall/snowfall rate varies but the
wiping interval remains constant.
– Rain/snow is falling but the wipers do
not operate. ( ; $ 0 3 / (
(1)
& $ 8 7 , 2 1
Page 117 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
& D Q F H O O D W L R Q R I W K H & U X L V H & R Q W U R OThe “SET” indicator light will go off and the
cruise control will be canceled temporarily
with following procedures:
• Push the “CANCEL” switch (2).
• Depress the brake pedal.
• Depress the clutch pedal.
• The vehicle speed falls more than about
20 percent from the set speed.
• Any time the vehicle speed falls below
40 km/h (25 mph).
To resume the previously set speed, push
the “RES +” switch (3) and turn on the
“SET” indicator light. Besides, the vehicle
speed has to be above 40 km/h (25 mph)
when the vehicle is not in the above condi-
tions.
To turn off the cruise control system, push
the “CRUISE” switch (1) and make sure
the “CRUISE” indicator light is off.
Also, if the malfunction indicator light in the
instrument cluster comes on or blinks, the
cruise control system will be turned off.
NOTE:
If you turn off the cruise control system, the
previously set speed in the memory is
cleared. Reset your cruising speed again.
3 D U N L Q J 6 H Q V R U V L I H T X L S S H G
61MM0A192
(1) Symbol representing an obstacle
detected by parking sensor*
* This symbol represents an obstacle
that is located to the right rear at
the vehicle.
• The parking sensor system uses ultra-
sonic sensors to detect obstacles near
the rear bumper. If obstacles are sensed
while you are parking or moving the
vehicle slowly, the system warns you by
sounding a buzzer and displaying sym-
bols representing the obstacles on the
information display in the instrument
cluster.
• The system emits an ultrasonic wave
and the relevant sensor detects the
return of the wave reflected by an obsta-
cle. The system measures the time
taken by the ultrasonic wave to reach the
obstacle and return from it, from which it
determines the obstacle’s position.
• The parking sensor function can be used
when you press the engine switch tochange the ignition mode to “ON”, the
gearshift lever is in “R” position and the
parking sensor switch is in the “ON”
position. This function is helpful in the
following cases: pulling over to the curb;
parallel-parking the vehicle; steering the
vehicle into a garage; driving along an
alley; and moving slowly in a place with
obstacles.
(1)
: $ 5 1 , 1 *
Page 118 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
6 H Q V R U / R F D W L R Q V 2 Q W K H U H D U E X P S H U
64MS170
(1) Rear center sensors (2 places)
(2) Rear corner sensors (2 places) : R U N L Q J V H Q V R U V
The sensors that work depends on the
position of the gearshift lever as follows:
$ S S U R [ L P D W H D U H D V Z K H U H R E V W D F O H V F D Q
E H G H W H F W H G
64MS007
• Any obstacle within about 20 cm (8 in)
from the sensor or just below the sensor
is not detectable.
• The sensors can detect an obstacle up
to about 1.5 m (5 ft) from the rear of
vehicle.
NOTICE
Page 119 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
NOTE:
• Thin poles or obstacles lower than the
sensors may become undetectable as
the vehicle moves closer to them even if
they have been detected from longer
distances.
• The distance calculated by the system to
a road sign or similar obstacle may be
shorter than the actual distance.
: $ 5 1 , 1 *
(Continued)
Page 120 of 288
Downloaded from www.Manualslib.com manuals search engine 2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
+ R Z W R 8 V H W K H 3 D U N L Q J 6 H Q V R U 3 D U N L Q J V H Q V R U V Z L W F K
61MS403
(1) Parking sensor switch
(2) Indicator
(2)
(1)
• When the ignition mode is “ON” and the indicator light in the parking sensor switch is on,
indicating that the parking sensor is ready for operation under the following conditions:
– The gearshift lever is in the “R” position.
– The vehicle’s forward moving speed is not more than approx. 9 km/h (6 mph) when
decelerating the vehicle such as for parking.
– The vehicle’s forward moving speed is not more than approx. 13 km/h (9 mph) when
accelerating.
• To deactivate the parking sensor, push the parking sensor switch and make sure the
indicator light goes off.
NOTE:
If you push the parking sensor switch from the OFF to ON position when the ignition mode
has been changed to ON by pressing the engine switch, the inside buzzer sounds. 6 Z L W F K S R V L W L R Q 6 W D W H ( ; $ 0 3 / (
ON
• When the indicator light is on and all necessary conditions are
met, system becomes ready for operation.
( ; $ 0 3 / (
OFF
• The system does not operate. Push the switch to turn off the
indicator if you do not wish to use the parking sensor.
Page 121 of 288
Downloaded from www.Manualslib.com manuals search engine
2 3 ( 5 $ 7 , 1 * < 2 8 5 9 ( + , & / (
0 6 (
2 E V W D F O H , Q G L F D W L R Q E \ 3 D U N L Q J 6 H Q
V R U
64MS008
(1) Obstacle detected by rear center sen-
sors
(2) Obstacle detected by rear corner sen-
sors
(1) (2) (2)
( ; $ 0 3 / (
Upon detecting an obstacle, the parking sensor causes an interior buzzer to sound and a
symbol representing the obstacle appears on the information display in the instrument
cluster.
• A different symbol is displayed depending on the direction and distance of the obstacle.
• A buzzer located behind the rear seat sounds when a sensor at the rear detects an
obstacle.
• Warnings when obstacles are detected by corner sensors
• Warnings when obstacles are detected by center sensors
NOTE:
• Symbols are displayed with a short delay after the detection of obstacles.
• If the system detects multiple obstacles simultaneously, the display shows all of their
positions using the corresponding symbols. However, the buzzers will sound only for
the nearest obstacles. ' L V W D Q F H D S S U R [ % X ] ] H U 6 \ P E R O
45 – 60 cm
(18 – 24 in)Short beeps at short intervals Three lines
35 – 45 cm
(14 – 18 in)Short beeps at very short intervals Two lines
Less than 35 cm
(14 in)Continuous beep One line
' L V W D Q F H D S S U R [ % X ] ] H U 6 \ P E R O
60 – 150 cm
(24 – 59 in)Short beeps at long intervals
Three lines
45 – 60 cm
(18 – 24 in)Short beeps at short intervals
35 – 45 cm
(14 – 18 in)Short beeps at very short intervals Two lines
Less than 35 cm
(14 in)Continuous beep One line