2015 SKODA SUPERB tow bar

Fig. 135
Remove the left side cover / store roll-up cover
Read and observe
and on page 106 first.
Extending
›
Grasp the cover at grip-point
A
and pull it out in the direction of the arrow
1
until it audibly clicks into place » Fig. 134.
Retracting
›
Press the cover at grip-point
A
in the direction of the arrow
2
» Fig. 134 .
The cover rolls up automatically to the intermediate position
B
.
The cover rolls up fully by pressing the cover in the handle area
A
in direction
of arrow
3
.
Removing/inserting
The fully rolled luggage compartment cover can be removed.
›
Press on the side of the cross bar in the direction of arrow
4
and remove
the cover in the arrow direction
5
» Fig. 134 .
Insertion takes place in reverse order.
Stowage
If the vehicle is equipped with the variable loading floor, then the removable
roll-up luggage compartment cover can be stowed in the recesses of the lug-
gage compartment side trim.
›
Fold the variable loading floor into the upper position » page 115.
›
Open the side trays on both sides of the luggage compartment and remove
» Fig. 138 on page 112 - 
.
›
Remove the left side cover in the arrow direction
1
» Fig. 135 .
›
Insert the roll-up cover in the recesses of the side trim in the arrow direction
2
.
›Stow the roll-up cover in the direction of the arrow 3
» .›Reinsert the left side cover in the opposite direction to the arrow 1.›
Close the side trays on both sides of the luggage compartment.
›
Fold out the variable loading floor to the upper position.
WARNINGNo objects should be placed on the foldable boot cover. This could endan-
ger the vehicle occupants during sudden braking or vehicle impact.
CAUTION
If you want to stow the roll-up luggage compartment cover and the multifunc-
tion tray at the same time , then it is necessary that the rear part of the roll-up
luggage compartment is covering the multifunction tray.
Roll-up cover - automatic rolling-up
Read and observe
and on page 106 first.
The automatic rolling up of the roll-up cover (hereafter as function) eases ac-cess tot he luggage compartment.
When opening the boot lid with the function activated, the roll-up cover auto-
matic rolls-up of the intermediate position
B
» Fig. 134 on page 109 .
This function can be activated/deactivated in the Infotainment » Owner´s
Manual Infotainment , chapter CAR - vehicle settings .
110Using the system

Multi-function pocketFig. 136
Pull out / insert / push in / remove multi-function pocket
Fig. 137
Remove the left side cover / store multifunction tray
Read and observe
and on page 106 first.
The multifunction pocket (following as pocket) is provided for the storage of
clothing and light objects with no sharp edges.
The maximum permissible load of the multifunction box is 3 kg.
Removal and fitting›Fold down the front hooks on both sides of the luggage compartment in the
direction of arrow 1
» Fig. 136 .
›
Grasp the rear bar
A
with both hands and withdraw the pocket in arrow di-
rection
2
.
›
Place the rear bar onto the two hooks that are folded forward in the direc-
tion of the arrow
3
all the way to the stop.
Pushing in
›
Remove the rear bar from the hook in the direction of the arrow
4
» Fig. 136 .
›
Push in the pocket in the direction of the arrow
5
.
›
Place the rear bar against the front bar and press them together at both
ends
B
.
›
The front hooks on both sides of the luggage compartment fold back oppo-
site to the direction of arrow
1
.
Removing/inserting
 The roll-up luggage compartment cover must already have been removed.
›
Remove the pocket from the fittings in the direction of the arrow
6
» Fig. 136
.
Insertion takes place in reverse order.
›
When inserting, push the end of the bar marked 
 into the right receptacle
and the end of the bar marked 
 into the left receptacle. The arrows should
be pointing forward.
Stowage
If the vehicle is equipped with the variable loading floor, then the removable
pocket cover can be stowed in the recesses of the luggage compartment side
trim.
›
Fold the variable loading floor into the upper position » page 115.
›
Open the side trays on both sides of the luggage compartment » Fig. 138 on
page 112 -
 .
›
Remove the left side cover in the arrow direction
1

» Fig. 137 .
›
Insert the tray in the recesses of the side trim in the arrow direction
2
.
›
Stow the tray in the direction of the arrow
3
» .
›
Reinsert the left side cover in the opposite direction to the arrow
1
.
›
Close the side trays on both sides of the luggage compartment.
›
Fold out the variable loading floor to the upper position » page 115. 
111Transporting and practical equipment

›Stop the vehicle and steer opposite until the yellow lines 6 the red line 8fade into each other (required roadway alignment). Hold the steering wheel
in this position.
Orientation lines are displayed » Fig. 187 on page 153 in the display.›
Carefully move backwards.
›
Stop the vehicle when 
appears the display, or at a safe distance from the
obstacle situated behind the vehicle.
Note
The guidance in the parking space is cancelled due to the system when the
steering wheel is set for a period of time against the required road direction.
The parking is to be started again.
Mode - driving up to a trailer / distance monitoring
Fig. 190
Display
Read and observe and on page 151 first.
In this mode, the area behind the vehicle is shown at the top of the display.
Vehicles with towing hitch
If your vehicle is factory fitted with a tow-bar, this mode supports the driver
when the vehicle approaches a trailer draw bar.
Display » Fig. 190
Ball head of the towing device
Lines for the distance estimation (at a distance of about 10 cm)
Line for approaching a trailer draw bar
Trailer draw bar
The line
C
moves depending on the steering angle and indicate the roadway
on which the vehicle would take with the current steering wheel position.
ABCDVehicles without towing hitch
If your vehicle is not factory equipped with a towing device, a red line for moni-
toring the distance to obstacles is displayed at a distance of 40 cm behind the
vehicle.
Mode - monitor the area behind the vehicle
Read and observe
and on page 151 first.
In this mode, the area behind the vehicle is shown in the display.
The mode is suited for the entire view of the situation behind the vehicle.
Park Assist
 Introduction
This chapter contains information on the following subjects:
Functioning
156
Parking space search
157
Switch to park mode
157
Reverse parking
157
Park forward
158
Departing from a parallel parking space
159
Automatic brake assist
159
Information messages
159
Park Assist (following referred to system) helps drivers park in suitable parallel
and perpendicular parking places or also to manoeuvre out of parallel parking
spaces.
The system takes over the steering movements when parking or leaving a
parking space. The driver operates the pedals and the shift lever or gear selec-
tor.
The state in which the steering wheel is operated by the system, is referred to
as parking operation.
The Park Assist is an extension of the parking aid » page 147 and operates on
the basis of data collected by the ultrasonic sensors.
For this reason, the chapter on the parking aid is to be read carefully and the safety notes are to be observed. 
155Assist systems

Hitch and trailer
Hitch
Introduction
This chapter contains information on the following subjects:
Swinging in and out the tow bar
184
Mount accessories
185
The maximum trailer draw bar load is 90 kg/h.
The draw bar load information on the type plate of the towing device is merely
a test value for the towing device. The vehicle-specific information is detailed
in the vehicle documents.
WARNING■ Do not use the towing equipment if it is damaged or incomplete.■Do not modify or adapt the towing device in any way.
Note
■ The towing vehicle by means of the towing device » page 233.■If the towing device is removed completely, it must be replaced with the
original reinforcement of the rear bumper which is part of the mount for the
towing eye.
Swinging in and out the tow bar
Fig. 220
Tow bar: swing in and out
Read and observe on page 184 first.
The tow bar is located in the rear bumper of the vehicle.
In addition to the handle
A
» Fig. 220 there is a warning light that indicates
whether the tow bar is locked - lit green, or is not locked - flashes red.
Swing out the tow bar
›
Open the tailgate.
›
Pull the handle
A
to position
1
» Fig. 220 » .
The tow bar pivots out in the direction of arrow
2
and the indicator beside
the handle flashes red.
›
The handle
A
may retract slowly » .
›
Press the tow bar in the direction of the arrow
2
, until it audibly clicks into
place.
The indicator next to the handle lights green.
Swivel tow bar
 The trailer must be uncoupled from the tow bar.
 An adapter may not be plugged into the 13-pin socket.
›
Open the tailgate.
›
Pull the handle
A
to position
1

» Fig. 220 .
The tow bar is unlocked and the indicator beside the handle flashes red.
›
The handle
A
may retract slowly » .
›
Swing in the tow bar into the bumper in the direction of arrow
3
until it
clicks into place.
The indicator next to the handle lights green.
Check latching
Before every journey when the tow bar is swung out check whether the warn- ing light is indicating green.
If the tow bar is incorrectly locked the warning light flashes red, after the igni-
tion is switched on an acoustic signal is sounded and the following message
appears in the instrument cluster.
Check towing bracket!TOWING BRACKET PLEASE CHECK


184Driving

WARNING■Take care with the towing device - it may cause injury.■Do not use the towing device, if the warning light is not green.■
If the tow bar cannot be correctly latched then do not use and have it
checked by a specialist.
■
Do not manipulate the handle
A
while a trailer is coupled to the tow bar.
■
Always swing the tow bar into the bumper when the towing device is not
being used.
CAUTION
■ Always check whether the handle A is properly seated in the starting posi-
tion.■
Take care with the towing device - there is a risk of damage to the swivel
mechanism.
Mount accessories
Fig. 221
Illustration of the maximum per-
missible projection of the ball
head of the towing hitch and the
permissible total weight of the
accessories including the load
depending on the load centre of
gravity
Read and observe on page 184 first.
An accessories can mounted on the ball head of the towing hitch (e.g. bike car-
riers).
If this accessory is used, the maximum permissible overhang of the ball head
of the towing hitch and the permissible gross vehicle weight of the accesso-
ries including load are to be checked.
The maximum permissible overhang of the ball head of the towing hitch is 70
cm » Fig. 221 .
The total permitted weight of the accessories including load changes varies
as the distance of the centre of gravity of the load from the ball head of the
towing hitch increases.
Distance of the centre of gravity of the load from the ball headPermissible total weight of the ac- cessories, including load0 cm90 kg30 cm75 kg60 cm35 kg70 cm0 kgWARNING■Never exceed the permissible gross weight of the accessory including
load - there is a risk of damaging the towing device.■
Never exceed the permissible protrusion of the ball head including towing
device - there is a risk of damaging the towing device.
Note
We recommend that you use accessories from ŠKODA Original Accessories.
Trailer
 Introduction
This chapter contains information on the following subjects:
Coupling / uncoupling trainer
186
Loading a trailer
186
Trailer load
187
Towing a trailer
188
Anti-theft alarm system
189
The trailer can be hitched to the ball head of the towing device.
185Hitch and trailer

Coupling / uncoupling trainerFig. 222
Housing of the 13 pin socket,
safety eyelet
Connect and disconnect
›
Swing out the tow bar » page 184.
›
Place the trailer onto the ball.
›
Plug the trailer cable into the 13-pin socket
A
» Fig. 222 .
If the trailer that is to be towed has a 7-pin connector, you can use a suitable
adapter from ŠKODA Original Accessories to establish a connection to the elec-
tricity.
›
Hook the breakaway cable of the trailer onto the safety eyelet
B
.
The breakaway cable of the trailer must sag in all trailer positions relative to
the vehicle (sharp curves, reverse driving and the like).
Uncoupling takes place in reverse order.
Exterior mirrors
You should have additional exterior mirrors fitted if you are not able to see the
traffic behind the trailer with the standard rear-view mirrors.
Headlights
The front of the vehicle may lift up when a trailer is being towed and the head-
lights may dazzle other road users.
Adjust the headlights using the headlight beam control » page 67, Operating
the lights 1)
.
Power to the trailer power grid
For the electrical connection between the vehicle and trailer, the power for the
trailer power grid is supplied by the vehicle.
The power supply works with ignition on or off.
With the ignition off, the battery of the towing vehicle is discharged by activa-
ted consumers.
At low charge state of the vehicle battery power to the trailer is interrupted.WARNING■ Improperly connected trailer electrical installations may cause accidents
or serious injury due to electric shock.■
Work on the electrical system must only be carried out by specialist ga-
rages.
■
Never directly connect the trailer's electrical system with the electrical
connections for the tail lights or other current sources.
■
After coupling the trailer and connecting up the power socket, check the
rear lights on the trailer to ensure they are working.
■
Never use the safety eyelet for towing!
CAUTION
Improperly connected trailer electrical installations may cause malfunction of
the entire vehicle electronics.
Note
■ The total power consumption of all the connected consumers on the trailer
must not exceed 350 watts.■
Coat the ball head of the towing device with a suitable grease whenever
necessary.
Loading a trailer
Distribution of the cargo
Distribute the cargo in the trailer in such a way that heavy items are located as
close to the trailer axle as possible. Secure the items from slipping.
The distribution of the weight is very poor if your vehicle is unladen and the
trailer is laden. Maintain a particularly low speed if you cannot avoid driving
with this combination.
Tyre pressure
Correct the tyre inflation pressure on your vehicle for a “full load” » page 217.
1)
Applies to vehicles with xenon headlights.
186Driving

Permissible trailer load - Superb EstateEngineGearboxPermissible trailer load, braked (kg)Permissible trailer load, unbraked (kg)Gradients of up to 12 %Gradients of up to 8 %a)1.4 l/92 kW TSIMG16001800690
1.4 l/110 kW TSI ACT
MG16001900700MG 4x418002000750DSG160019007201.4 l/110 kW TSIMG16001900700DSG160019007101.8 l/132 kW TSIMG18002000740DSG180020007502.0 l/162 kW TSIDSG200020007502.0 l/206 kW TSIDSG 4x422002200750
1.6 l/88 kW TDI CR
MG15001800740MG (GreenLine)15001800750DSG15001800750
2.0 l/110 kW TDI CR
MG20002000750MG 4x422002200750DSG200020007502.0 l/130 kW TDI CRDSG20002000750
2.0 l/140 kW TDI CR
MG20002000750DSG20002100750DSG 4x422002200750a)
Only valid for some countries.
WARNINGNever exceed the maximum permissible axle and draw bar load or the per-
missible weight of the trailer - risk of accident!
Towing a trailer
Driving speed
For reasons of safety do not drive more than 100 km / h when the towing vehi-
cle is a passenger car of category M1.
For reasons of safety do not drive more than 80 km / h when the towing vehi-
cle is a lorry of category N1.
Immediately reduce your speed as soon as even the slightest swaying of the
trailer is detected. Never attempt to stop the trailer from “swaying” by acceler-
ating.
Brakes
Apply the brakes in good time! If the trailer is fitted with a trailer brake, apply
the brakes gently at first, then brake firmly. This will avoid brake jolts resulting
from the trailer wheels locking. 188Driving

Clean wheels, door sills and similar parts last. Use a second sponge for such
areas.
Give the vehicle a good rinse after washing it and dry it off using a chamois
leather.WARNINGProtect your hands and arms from sharp-edged metal parts when cleaning
the under floor or the inside of the wheel housings or the wheel trims – risk
of cuts!
CAUTION
■ Only apply slight pressure when cleaning the vehicle's paintwork.■Do not wash your vehicle in bright sunlight – risk of paint damage.
Automatic car wash systems
Read and observe
and on page 193 first.
The usual precautionary measures must be taken before washing the vehicle
in an automatic car wash system (e.g. closing the windows and the sliding/tilt-
ing roof etc.).
If your vehicle is fitted with any particular attached parts, such as a spoiler,
roof rack system, two-way radio aerial etc., it is best to consult the operator of
the car wash system beforehand.
After an automatic wash with wax treatment, the lips of the wipers should be
cleaned with cleaning agents specially designed for the purpose, and then de-
greased.
CAUTION
Before driving through a car wash fold in the exterior mirrors - there is a risk of
damage.
Washing with a high-pressure cleaner
Read and observe
and on page 193 first.
When washing the vehicle with a high-pressure cleaner, the instructions for
use of the equipment must be observed. This applies in particular to the pres-
sure used and to the spraying distance .
Maintain a sufficiently large distance to the parking aid sensors and soft mate-
rials such as rubber hoses or insulation material.
CAUTION
■ The films should not be washed with any high-pressure cleaners - risk of
damage » page 195 .■
Do not aim the water jet directly at the lock cylinders or the door or opening
joints when washing the vehicle in the winter – there is a risk of freezing.
■
The sensors of the parking aid can be sprayed only for a short time and there
must be a minimum distance of 10 cm - there is a risk of damage.
■
When washing the vehicle, do not point the water jet directly at the tow bar
or the trailer socket - there is a risk of seal damage or washing out the grease.
Cleaning vehicle exterior
 Introduction
This chapter contains information on the following subjects:
Vehicle paint work
195
Films
195
Plastic parts
196
Rubber seals
196
Chrome and anodized parts
196
Windows and external mirrors
196
Headlight glasses
197
Camera lens
197
Door closing cylinder
197
Cavity protection
197
Jack
197
Wheels
197
Under-body protection
198
Wiper blades
198
We recommend using vehicle care products from ŠKODA Original Accessories.
These are available from ŠKODA Partners. The usage instructions on the pack-
age must be observed. 
194General Maintenance