2015 SKODA FABIA turn signal bulb

Other incidents
The following reasons can also apply if the warning light  is illuminated.
▶ The vehicle is loaded on one side. Distribute loads as evenly as possible.
▶ The wheels of one axle are loaded more heavily (e.g. when towing a trailer or
when driving uphill or downhill).
▶ Snow chains are fitted.
▶ A wheel has been changed.
CAUTION
Under certain circumstances (e.g. sporty style of driving, wintry or unpaved
roads) the warning light  in the instrument cluster can be delayed or does
not light up at all.
 Fuel reserve
Read and observe
on page 32 first.
 illuminates - the fuel level in the fuel tank has reached the reserve level (ap-
proximately 7 litres).
Please refuel. Range: ...

kmPLEASE REFUEL RANGE …

km
An audible signal sounds as a warning.
Note
The text in the display goes out after refuelling and driving a short distance.
  Turn signal system
Read and observe
on page 32 first.
 flashes - the left turn signal is turned on.
 flashes - the right turn signal is turned on.
If there is a fault in the turn signal system, the warning light flashes at twice
its normal rate. This does not apply when towing a trailer.
When the hazard warning light system is switched on, this will cause all of the
turn signal lights as well as both warning lights to flash.
 Trailer turn signal lights
Read and observe
on page 32 first.
 flashes - the trailer lights are switched on.
If a trailer is hitched and the warning light 
is not flashing, one of the trailer
turn signal lights has failed.
An example message in the display of the instrument cluster
Trailer: check left turn signal!TRAILER TURN SIG_ CHECK LEFT
Check the trailer bulbs.
 Fog lights
Read and observe
on page 32 first.
 illuminates - the fog lamps are switched on.
 Speed control/speed limiter
Read and observe
on page 32 first.
 illuminates - the vehicle speed is limited by the speed regulator system
and/or the automatic distance control or by the speed limiter.
 flashes - the speed set with the limiter has been exceeded.
 Brake pedal (automatic transmission)
Read and observe
on page 32 first.
 illuminates - apply the brake.
 Main beam
Read and observe
on page 32 first.
 illuminates - the main beam or the headlight flasher is switched on.
35Instruments and warning lights

No.Power consumer8Windscreen wipers9Central control unit, battery data module10ABS or ESC11Not assigned12Engine components13Brake pedal switch14Engine components, coil of the fuel pump relay15Engine control unit16Starter17Engine control unit18Engine components, coils of the relay for auxiliary electric heater, radi-
ator fan19Lambda probe20Engine components, glow plug system, heating for the crankcase ven-
tilation
Bulbs
 Introduction
This chapter contains information on the following subjects:
Bulb arrangement in the headlights
185
Removing and installing the cover in the front wheel arch
185
Fitting and removing the wash water container nozzle
185
Replacing the low beam and high beam bulb (halogen headlights)
186
Change bulb for turn signal switch (halogen headlight)
186
Replacing the parking light bulb (halogen headlights)
187
Changing bulb for daytime running lights switch (halogen headlight)
187
Replacing the dipped beam bulb (halogen projector headlights)
187
Replacing the high beam bulb (halogen projector headlights)
188
Replacing the turn signal switch bulb (halogen projector headlights)
188
Replacing the bulb for the fog light
189
Changing the licence plate light bulb
189
Rear Light
190
Replacing bulbs in rear light
190Some manual skills are required to change a bulb. For this reason, if uncertain,
we recommend that bulbs are replaced by a specialist garage or other expert
help is sought.
▶ Switch off the ignition and the relevant lights before replacing a bulb.
▶ Faulty bulbs must only be replaced with the same type of bulbs. The designa-
tion is located on the light socket or the glass bulb.
A stowage compartment for replacement bulbs is located in a plastic box in
the spare wheel or underneath the floor covering in the luggage compartment.
We recommend having the headlight settings checked by a specialist garage
after replacing a bulb in the low, high or fog beam.
Visit a specialist garage if an LED is faulty.WARNING■ Always read and observe the warnings before completing any work in the
engine compartment » page 149.■
Accidents can be caused if the road in front of the vehicle is not suffi-
ciently illuminated and the vehicle cannot or can only be seen with difficul-
ty by other road users.
■
Bulbs H8, H7 and H4 are pressurised and may burst when changed - there
is a risk of injury! We therefore recommended wearing gloves and safety
glasses when changing a bulb.
CAUTION
■ Do not take hold of the glass bulb with naked fingers (even the smallest
amount of dirt reduces the working life of the light bulb). Use a clean cloth,
napkin, or similar.■
The protective cap of the bulb must always be properly inserted into the
headlamp. Water and dirt may get into the headlamp if the cover is not re-
placed properly - there is a risk of damage to the headlamp!
Note
■ This Owner's Manual only describes the replacement of bulbs where it is pos-
sible to replace the bulbs on your own without any complications arising. Other
light bulbs should be changed by your specialist garage.■
We recommend that you always carry a box of replacement bulbs in the vehi-
cle. Replacement bulbs can be purchased from ŠKODAOriginal Accessories.
184Do-it-yourself

Bulb arrangement in the headlightsFig. 203
Principle sketch: Halogen headlights/halogen projector head-
lights
Read and observe
and on page 184 first.
The vehicle is equipped with headlights with halogen bulbs.
Bulb arrangement » Fig. 203
Dayl. dri. light
Low beam, high beam and parking light
Flashing
Low beam
High beam and turning signal switch
Removing and installing the cover in the front wheel arch
Fig. 204
Remove the plastic cover
Read and observe and on page 184 first.
The cover in the front wheel must be removed in order to change certain light
bulbs.
ABCDEDetails about removing the cover - if needed - are given in the description of
each lamp change.
Removing›
Adjust front wheels in the direction of centre of the vehicle.
›
Insert the clamp for removing the full wheel covers » page 167, Vehicle tool
kit into the recess in the cover.
›
Remove the cover by pulling the hook in the direction of arrow » Fig. 204.
Fitting
›
Insert and push the cover into the corresponding opening.
The cover must engage securely.
Fitting and removing the wash water container nozzle
Fig. 205
Remove the holder of the wash water container nozzle
Read and observe
and on page 184 first.
The holder of the wash water container nozzle must be removed in order to
replace some light bulbs. The holder is located in the engine compartment,
front right. 
185Fuses and light bulbs

Details about removing the holder - if needed - are given in each lamp replace-
ment description .
Removing›
Remove the container nozzle
A
from the holder in the direction of arrow
1
» Fig. 205 .
›
Insert a finger into the recess
B
in the direction of arrow
2
and lift the catch
C
in the direction of arrow
3
.
›
Remove the holder of the container nozzle in the direction of arrow
4
.
Fitting
›
Slide the holder of the container nozzle in the opposite direction to the ar-
row
4
» Fig. 205 .
The holder must engage firmly.
›
Push the container nozzle into the holder in the opposite direction to the ar-
row
1
.
Replacing the low beam and high beam bulb (halogen headlights)
Fig. 206
Replacing the bulb for low beam and main beam
Read and observe
and on page 184 first.
›
Remove the relevant cover in the front wheel arch » page 185.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
B
» Fig. 203 on page 185 .
›
Press the connector latch and remove the plug connector by jiggling in the
direction of arrow
1
» Fig. 206 .
›
Push in the spring in the direction of the arrow
2›
Release the spring in the direction of the arrow
3
.
›Remove the defective bulb in the direction of arrow 4.›Fit a new bulb into the headlamp and secure the spring in the opposite direc-
tion to the arrow 3
.
›
Insert the plug in the opposite direction to the arrow
1
.
›
Fit protective cap
B
» Fig. 203 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
›
Replace the appropriate cover in the front wheel arch » page 185.
Change bulb for turn signal switch (halogen headlight)
Fig. 207
Changing the bulb for the front
turn signal light
Read and observe and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
C
» Fig. 203 on page 185 .
›
Turn the socket with the bulb in the direction of arrow
1
» Fig. 207 .
›
Remove the socket with the bulb in the direction of arrow
2
.
›
Insert the socket with the new bulb in the opposite direction to the arrow
2
.
›
Turn the socket with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
C
» Fig. 203 on page 185 .
186Do-it-yourself

›Remove the protective cap D
» Fig. 203 on page 185 .›Turn the holder with the bulb in the direction of arrow 1 » Fig. 210 .›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
›
Fit protective cap
D
» Fig. 203 on page 185 .
›
Replace the appropriate cover in the front wheel arch » page 185.
Replacing the high beam bulb (halogen projector headlights)
Fig. 211
Changing the bulb for the main beam
Read and observe
and on page 184 first.
Remove the holder of the wash water container nozzle before replacing the
lamp in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 203 on page 185 .
›
Turn the holder with the bulb in the direction of arrow
1
» Fig. 211 .
›
Remove the holder with the bulb in the direction of arrow
2
.
›
Remove the bulb from the holder in the direction of the arrow
3
.
›
Insert a new bulb into the connector so that the lug
A
on the connector
snaps into the groove on the bulb.
›
Insert the connector with the new bulb into the headlight in the opposite di-
rection to the arrow
2
.
›
Turn the connector with the new bulb in the opposite direction to the arrow
1
until it stops.
› Fit protective cap E
» Fig. 203 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
Replacing the turn signal switch bulb (halogen projector
headlights)
Fig. 212
Changing the bulb for the turn signal light
Read and observe
and on page 184 first.
To replace lamp, first remove the bracket of the wash water container nozzle
in the right headlight » page 185.
›
Remove the protective cap
E
» Fig. 203 on page 185 .
›
Remove the bulb holder with the bulb by jiggling it out in the direction of the
arrow
1
» Fig. 212 .
›
Grasp the lamp socket at the places marked by arrows.
›
Remove the faulty bulb from the holder in the direction of the arrow
2
.
›
Push a new bulb into the bulb holder up to the stop.
›
Replace the bulb holder in the headlamp with the bulb.
›
Fit protective cap
E
» Fig. 203 on page 185 .
After changing the lamp in the right headlamp, replace the holder of the wash
water container nozzle » page 185.
188Do-it-yourself

Heating95
Control elements95
Exterior mirrors68
Seats71
HHC116
Hill Start Assist (HHC)116
Hitch127
Drawback load127
Hooks85
Horn26
I
i-Pad holder Handling
82
Ice scrapers142
Ignition lock101
Immobilizer100
Individual settings Locking
52
Unlocking52
Inertia reel13
Information system39
Compass point display45
Door warning39
Gear recommendation39
MAXI DOT display42
Multifunction display40
operation40
Service interval display46
Information system operation40
Infotainment4
Instrument cluster27
Auto-check control39
Counter for distance driven30
Display29
Fuel gauge30
Overview28
Revolution counter28
Temperature gauge29
Warning lights31
Interior care144
Natural leather145
interior light Front
64
Interior monitor55
iPad holder behind the headrests
82
ISOFIX22
J
Jack
167
Maintenance143
Jacking points Raise vehicle
170
Jump-starting174
K
KESSY Locking
51
Unlocking51
Key Locking
50
Start the engine101
Stopping the engine101
Switch off the ignition101
Switch on the ignition101
Unlocking50
L
Lamp failure Warning light
37
Lamps Warning light
37
Leather Natural leather care
145
LEAVING HOME63
Lever Main beam61
Turn signal61
Levers Windscreen wipers
67
Light Cockpit
64
COMING HOME / LEAVING HOME63
Front fog lights62
Headlights with CORNER function62
Rear fog light62
Replacing bulbs184
Lighting Luggage compartment
83
Lights59
Automatic driving lamp control61
Daylight running60
Hazard warning light system63
Headlight flasher61
Headlight range adjustment60
Low beam60
Main beam61
parking lights60
Parking lights63
Switching on and off60
Turn signal61
Warning lights31
Load194
Locking Individual settings
52
KESSY51
Key50
Remote control50
Locking and unlocking the vehicle from the in- side
52
Locking the door without a locking cylinder Emergency
178
Low beam60
205Index

Petrolsee fuel148
Phone see Infotainment
4
Plastic parts142
Pocket in the luggage compartment
85
Polishing vehicle paint work see vehicle care
141
Power steering Warning light
32
Power windows56
Button in the front passenger door58
Force limitation58
Practical equipment Reflective vest
166
Practical features Pockets on the backs of the front seats
81
Pockets on the inner sides of the front seats81
Waste container77
Protective films141
R
Radiator fan
152
Radio see Infotainment
4
Raise vehicle170
Rear interior light
64
Rear-view mirror Exterior mirrors
68
Rear fog light62
Warning light33
Rear mirror67
Rear view mirror Interior mirror
68
Rear window - heater65
Recirculated air mode97
Refuelling147
Fuel147
Remote control Locking
50
Replacing the battery177
Synchronisation process178
Unlocking50
Remote control key Replacing the battery
177
Removing the bar ball, Step 1
131
bar ball, Step 2131
Repairs and technical alterations136
Replacing Bulb for the fog light
189
Bulb in rear light190
Bulbs184
Fuses - engine compartment183
High beam bulb (halogen projection-type head- lamp)
187
High beam bulb (halogen projector headlights) 188
Low beam and high beam bulb (halogen head- lights)
186
parking light bulb187
Rear window wiper blade180
turn signal switch bulb (halogen projector headlights)
188
Vehicle battery159
windscreen wiper blades179
Replenishing Coolant
155
Engine oil154
Windscreen washer fluid152
Revolution counter28
Rims160
Roller blind Luggage compartment cover
87
Roof Load
94
Roof rack93
mounting points94
Roof load94
Rubber seals142
Running-in Brake linings
111
Engine111
Tyres111
S
SAFE see SafeLock
52
SafeLock52
SAFELOCK see SafeLock
52
Safety8
Child safety20
Child safety seats20
Correct seated position8
Headrests70
ISOFIX22
TOP TETHER24
Save electrical energy112
Save fuel112
Seals Vehicle care
142
Seat Adjusting
69
Seat belt height adjustment
12
Warning light32, 36
Seat belts11
Belt tensioners14
fastening and unfastening13
Seatbelts Inertia reels
13
Seat belts The physical principle of a frontal collision
12
Seat features71
207Index