2015 Seat Alhambra headlights

Driving
Operating instructions The auxiliary heater exhaust system located
below the vehicle must be kept clear of snow,
mud and other objects. The exhaust gases
must not be obstructed in any way. The ex-
haust gases generated by the auxiliary heater
are removed via an exhaust pipe fitted under-
neath the vehicle.
On heating the vehicle interior, depending on
the outside temperature the warm air is first
directed at the windscreen and then to the
rest of the vehicle interior through the air
vents. If the air vents are turned towards the
windows, for example, the form of air distri-
bution may be affected.
Depending on the outside temperature, the
temperature at which the auxiliary heater
warms the vehicle interior may be somewhat
higher if the heating or air conditioner tem-
perature control is set to maximum before
switching the heating on.
Depending on the engine, vehicles with aux-
iliary heater may be fitted with a second bat-
tery in the luggage compartment that is re-
sponsible for powering the auxiliary heater.
Cases in which the auxiliary heater will not
switch on
● The auxiliary heater requires about as
much power as the dipped beam headlights.
If the battery charge is low, the auxiliary heat- er will switch off automatically or will not
even switch on. This avoids problems when
starting the engine.
●
The heater will switch on just once each
time. The timer will also have to be switched
back on every time it is required. Note
● Noise will be heard while the auxiliary
heater is running.
● When the air humidity is high and the out-
side temperature low, the heating system
may evaporate condensation from the auxili-
ary heater. In this case, steam may be re-
leased from underneath the vehicle. This is
completely normal and there is no need to
suspect a fault!
● If the auxiliary heater runs several times
over a prolonged period, the vehicle battery
may run flat. To re-charge the battery, drive
the vehicle for a long distance. As a general
rule, drive for as much time as the auxiliary
heating was working. Driving
Address Introduction The power steering is not hydraulic but elec-
tromechanical. The advantage of this steer-
ing system is that it disposes of hydraulic
tubes, hydraulic oil, the pump, filter and oth-
er components. The electromechanical sys-
tem saves fuel. While a hydraulic system re-
quires oil pressure to be maintained, electro-
mechanical steering only requires energy
when the steering wheel is turned.
With the power steering system, the assisted
steering function automatically adjusts ac-
cording to the vehicle speed, the steering tor-
que and the wheel turning angle. The power
steering only works when the engine is run-
ning.
WARNING
If the power steering is not working then the
steering wheel is much more difficult to turn
and the vehicle more difficult to control.
● The power steering only works when the
engine is running.
● Never allow the vehicle to move when the
engine is switched off.
● Never remove the key from the ignition if
the vehicle is in motion. The steering may » 131Technical specifications
Advice
Operation
Safety

Towing bracket device
●
With the engine running, the electrical
equipment on the trailer will be supplied with
power. Loading the trailer
Trailer weight / drawbar load
The trailer weight is the load that the vehicle
can pull
››› . The drawbar load is the vertical
weight of the tow hitch on the tow hitch ball
››› page 188.
The figur e
s for trailer weights and drawbar
load weights given on the data plate of the
tow hitch are for values of this model only.
The correct figures for your specific vehicle,
which may be lower than these figures for the
t o

w hitch, are given in the vehicle documen-
tation. The instructions in the official vehicle
documents take precedence.
For the sake of road safety, SEAT recom-
mends using the maximum allowed drawbar
load
. The handling of the combined vehicle
and trailer will be poor if the drawbar load is
too low.
The drawbar load increases the weight on the
rear axle, reducing the vehicle carrying ca-
pacity.
Gross combination weight
This figure refers to the combined weight of
the loaded vehicle and loaded trailer. Loading the trailer
The combined vehicle and trailer must be
balanced. Use the maximum drawbar load
authorised and do not overload the front or
the rear of the trailer:
●
Distribute loads in the trailer so that heavy
objects are as near to the axle as possible or
above it.
● Correctly secure the trailer load.
Tyre pressure
Inflate the trailer tyres according to the man-
ufacturer's instructions.
Inflate the towing vehicles tyres to the maxi-
mum ››› page 231. WARNING
Exceeding the maximum authorised axle
load, drawbar load or the gross combination
weight of the towing vehicle and trailer could
cause a serious accident with severe conse-
quences.
● Never exceed the specifications.
● With the actual load on the front and rear
axles, the maximum axle load should never
be exceeded. The weight on the front and rear
should never exceed the gross vehicle
weight. WARNING
If the load moves, the stability and safety of
the vehicle and trailer combination will be se-
riously affected and this could result in a seri-
ous accident.
● Always correctly load the trailer.
● Always secure loads correctly with suitable
and undamaged attachment rope or straps. Driving with a trailer
Adjusting the headlights
When towing a trailer, the front of the vehicle
may rise and so the dipped beam headlights
may blind other drivers. Use the headlight
range control to lower the cone of light. If you
do not have headlight range control, have
the headlights adjusted by a specialised
workshop. Vehicles with high-intensity dis-
charge lamps adapt automatically and do not
require adjustment.
Details of driving with a trailer
● If the trailer has an overrun brake, apply
the brakes gently at first and then, firmly.
This will prevent the jerking that can be
caused by the trailer wheels locking.
● As of the combined vehicle and trailer
mass, braking distances will be greater.
● Select a low gear before driving down a
steep hill to use the engine braking effect to »
185
Technical specifications
Advice
Operation
Safety

Advice
Automatic car washes
Always observe the instructions provided at
the automatic car wash. The standard pre-
cautionary measures prior to entering the car
wash should be taken to avoid damage to
the vehicle (close all windows, fold in exterior
mirrors). If the vehicle is fitted with additional
components (spoiler, roof-rack, aerial, etc.),
check with the car wash supervisor whether
these can enter the car wash ››› .
The vehicle paintwork is so durable that the
vehicle can normally be washed without
problems in an automatic car wash tunnel.
However, wear and damage to the paintwork
will depend on the type of car wash used.
SEAT recommends the use of car washes
without brushes.
To remove traces of wax on windows and to
prevent wiper blades from scratching, please
observe the following ››› page 197, Cleaning
windows and exterior mirrors .
Washing the car by hand
When washing the car by hand, use plenty of
water to soften the dirt first, and rinse off as
well as possible.
Then clean the vehicle with a soft sponge,
glove or brush using only slight pressure.
St ar
t at the roof and work downwards. Spe-
cial car shampoo should only be used for
ver

y persistent dirt. Rinse the sponge or glove thoroughly and of-
ten.
Wheels, sills and similar should be cleaned
last. Use a second sponge for this.
WARNING
Sharp components on the vehicle may cause
injury.
● Protect arms and hands from sharp edges
when cleaning the vehicle undercarriage or
the interior of the wheel hubs. WARNING
After the vehicle has been washed, the brak-
ing effect will be reduced (and the braking
distance increased) due to moisture (and ice
in winter) on the brakes.
● “Dry the brakes and remove ice” by braking
carefully. Ensure that you are not endanger-
ing other road-users or breaking traffic regu-
lations in the process. CAUTION
● The temperature of the water must not ex-
ceed +60 °C (+140 °F).
● To avoid damage to the paintwork, do not
wash the vehicle in full sun.
● Do not use rough sponges or similar which
could damage the surface to clean away the
traces of insects. ●
Never wipe the headlights with a dry cloth
or sponge, always moisten first. It is best to
use soapy water.
● Washing the vehicle in low temperatures:
When washing the vehicle with a hose, do
not direct water into the lock cylinders or the
gaps around the doors or roof. Locks and
seals could freeze! CAUTION
To prevent damage to the vehicle, please ob-
serve the following before entering an auto-
matic car wash: ● Compare the distance between the vehicle
wheels and the distance between the guide-
rails of the car wash to prevent damage to the
wheels and tyres!
● Switch off the rain sensor and the Au-
to Hold function before entering a car wash.
● Compare the height and width of your vehi-
cle with the available height and width when
entering and driving through the car wash.
● Fold in exterior mirrors Electrically retracta-
ble exterior mirrors must not be folded in or
out by hand. Always use the electrical power
control.
● To avoid damaging the bonnet paintwork,
rest the wipers on the windscreen after dry-
ing them. Do not let them fall!
● Lock the rear lid to prevent it from opening
unexpectedly while inside the car wash. 196

Emergencies
Starting
7. Start the engine of the vehicle with the boosting battery and let it run at idling
speed.
8. Start the engine of the vehicle with the flat battery and wait 2 or 3 minutes until the
engine is “running”.
Removing the jump leads
9. Before you remove the jump leads, switch off the dipped beam headlights (if they
are switched on).
10. Turn on the heater blower and heated rear
w indo
w in the vehicle with the flat battery.
This helps minimise voltage peaks which
are generated when the leads are discon-
nected.
11.When the engine is running, disconnect the leads in reverse order to the details
given above.
Connect the battery clamps so they have
good metal-to-metal contact with the battery
terminals.
If the engine fails to start, switch off the start-
er after about 10 seconds and try again after
about 1 minute. WARNING
● Please note the safety warnings referring to
working in the engine compartment
››› page 214.
● The b att

ery providing assistance must have
the same voltage as the flat battery (12V) and
approximately the same capacity (see imprint
on battery). Failure to comply could result in
an explosion.
● Never use jump leads when one of the bat-
teries is frozen. Danger of explosion! Even af-
ter the battery has thawed, battery acid could
leak and cause chemical burns. If a battery
freezes, it should be replaced.
● Keep sparks, flames and lighted cigarettes
away from batteries, danger of explosion.
Failure to comply could result in an explo-
sion.
● Observe the instructions provided by the
manufacturer of the jump leads.
● Do not connect the negative cable from the
other vehicle directly to the negative terminal
of the flat battery. The gas emitted from the
battery could be ignited by sparks. Danger of
explosion.
● Do not attach the negative cable from the
other vehicle to parts of the fuel system or to
the brake line.
● The non-insulated parts of the battery
clamps must not be allowed to touch. The
jump lead attached to the positive battery
terminal must not touch metal parts of the ve-
hicle, this can cause a short circuit. ●
Position the leads in such a way that they
cannot come into contact with any moving
parts in the engine compartment.
● Do not lean on the batteries. This could re-
sult in chemical burns. Note
The vehicles must not touch each other, oth-
erwise electricity could flow as soon as the
positive terminals are connected. Towing and tow starting
Introduction When towing, always respect legal require-
ments.
For technical reasons, it is not possible to
tow a vehicle if the battery is flat.
If the vehicle comes with the Keyless Access
system, towing is only allowed with the igni-
tion on!
The vehicle battery drains if the vehicle is
towed with the engine switched off and the
ignition connected. Depending on the battery
charge status, the drop in voltage may be so
large, even after just a few minutes, that no
electrical device in the vehicle may work e.g.
the hazard warning lights. In vehicles with
»
255
Technical specifications
Advice
Operation
Safety

Advice
To replace halogen headlight bulbs Fig. 211
In the engine compartment: left-
hand side headlight lining. A dipped beam
headlights, B daytime driving lights and
Cmain beam headlights and side lights Fig. 212
Left headlight. There is no need to remove the headlight to
replace bulbs.
Complete operations only in the sequence
given:
ABC
Turn signals (small lamp holder)Dipped beam
headlightsDaytime driving lightMain beam headlightsSide lights
1.Open the bonnet  ››› page 214.
2. Remove the rubber cover on the rear of the headlight.
3.Rotate the lamp holder 1 to the left
all the way and pull it out backwards with the bulb.Rotate the lamp holder to the left all the wayand pull it out backwards with the bulb.Press the wire clip downwards and
pull the lamp holder 2 out with the
bulb.Pull the lamp holder 3 out back-
wards with the bulb.
4.Depending on the model, the bulb is removed directly from the lamp holder or it may need to be rotated and then removed.
5.Replace the faulty bulb by a new identical bulb. 268

Fuses and bulbs
ABC
Turn signals (small lamp holder)Dipped beam
headlightsDaytime driving lightMain beam headlightsSide lights
6.Place the bulb holder in the headlight and rotate to the right all the way.Place the lamp holder in the head-
light and pull the wire clip upwards until it clicks into place.Place the lamp holder in the head-light and insert completely.
7. Insert the rubber cover. Note
The images show the left hand headlight
from behind. The structure of the right hand
side headlight is symmetric. To replace the xenon headlights bulb
Fig. 213
In the engine compartment: turn sig-
nal indicator cover. Fig. 214
Turn signal lamp holder 1 and turn-
ing light 2 There is no need to remove the headlight to
replace bulbs.
Complete operations only in the sequence
given:
Turn signals
1Turning lights 2
1.Open the bonnet 
››› page 214.
2.Rotate the cover ››› Fig. 213 in the direction of the
arrow and remove it.
Turn signals 1Turning lights 2
3.
Rotate the lamp holder
1 ››› Fig. 214 to the
left all the way and pull
it out backwards with
the bulb.Press the wire clip
downwards and pull the
lamp holder 2
›››
Fig. 214 out with the
bulb.
4.Depending on the model, the bulb is removed di-
rectly from the lamp holder or it may need to be ro- tated and then removed.
5.Replace the faulty bulb by a new identical bulb.
6.
Place the bulb holder in
the headlight and ro-
tate to the right all the
way.Place the lamp holder
in the headlight and
pull the wire clip up-
wards until it clicks into
place.
7.Rotate the cover ››› Fig. 213 in the opposite direc-
tion to the arrow as far as it will go. Always seek the help of a specialist when
changing the Xenon dipped beam and main
beam headlamps
››› in Introduction on
page 267. »
269
Technical specifications
Advice
Operation
Safety

Advice
Note
The illustrations show the left hand head-
light. The structure of the right hand side
headlight is symmetric. To replace the front bumper bulbs
Fig. 215
On the right-hand side of the front
bumper: removing the headlights. Fig. 216
Changing the bulbs in the head-
lights Complete operations only in the sequence
given:1.Pull the cover forwards, in the direction of the ar-
row
››› Fig. 215.
2.Unscrew the attachment screw ››› Fig. 215 1 us-
ing the screwdriver from the vehicle tool kit
››› page 244.
3.Tilt the headlight slightly forward and extract it
from its lateral attachments ››› Fig. 216 (small ar-
rows).
4.Release the connector ››› Fig. 216 1 and remove
it.
5.Rotate the bulb holder ››› Fig. 216 2 to the left all
the way, in the direction of the arrow, and pull it
out backwards with the bulb.
6.Replace the faulty bulb by a new identical bulb.
7.Place the bulb holder in the headlight and rotate
to the right all the way.
8.Insert the connector ››› Fig. 216 1 on the bulb
holder 2. The connector must audibly click into
place.
9.Place the headlight into its position ››› Fig. 216
(small arrows) and tilt it backwards.
10.Tighten the attachment screw ››› Fig. 215 1 us-
ing the screwdriver.
11.Replace the cover on the bumper ››› Fig. 215. 270

Index
Index
A
Abroad Extended stay abroad with your vehicle . . . . . 205
Sale of vehicle . . . . . . . . . . . . . . . . . . . . . . . . . 205
ABS See "Brake assist systems" . . . . . . . . . . . . . . . 154
Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Acoustic warnings Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
Adaptive headlights Dynamic . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
AdBlue Control lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Minimum quantity for a refill . . . . . . . . . . . . . . 213
Refilling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Tank filling capacity . . . . . . . . . . . . . . . . . . . . . 213
Warning lamp . . . . . . . . . . . . . . . . . . . . . . . . . . 212
Additional equipment . . . . . . . . . . . . . . . . . . . . . 190
Additional heater See "Auxiliary heater" . . . . . . . . . . . . . . . . . . . 128
Adjusting passenger exterior mirror . . . . . . . . . . . 86
Adjusting the seats front seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 88
Adjustment Correct sitting position . . . . . . . . . . . . . . . . . . . . . 6
Electric front seat . . . . . . . . . . . . . . . . . . . . . . . . 88
Head restraints . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Mechanical front seat . . . . . . . . . . . . . . . . . . . . . 88
Rear seats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 89
Seat with position memory . . . . . . . . . . . . . . . . 94
Steering wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Adjustments
Folding the seat backrest of the front passen-ger seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Headlight range . . . . . . . . . . . . . . . . . . . . . . . . . 79
Aerial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
Aerial built into the window . . . . . . . . . . . . . . . . . 205
AFS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Airbags description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Airbag system . . . . . . . . . . . . . . . . . . . . . . . . . . 18, 20 activation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Cleaning dash panel . . . . . . . . . . . . . . . . . . . . 204
Control lamp . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Deactivating the front passenger front airbag . 25
Deactivating using the key switch . . . . . . . . . . . 25
Differences between front passenger front air-bag systems . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Front airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
functioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Head-protection airbags . . . . . . . . . . . . . . . . . . 24
Knee airbag . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Locking the vehicle after airbag deployment . . 58
Repairs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Side airbags . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Use of child seats . . . . . . . . . . . . . . . . . . . . . . . . 25
Vehicle care . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
Air conditioner . . . . . . . . . . . . . . . . . . . . . . . . . . . 122 Air recirculation mode . . . . . . . . . . . . . . . . . . . 127
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Climatronic . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Electronic manual air conditioning . . . . . . . . . 123
Faults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Indirect ventilation . . . . . . . . . . . . . . . . . . . . . . 126
Things to note . . . . . . . . . . . . . . . . . . . . . . . . . . 126
User instructions . . . . . . . . . . . . . . . . . . . . . . . 125 Air conditioning
see "Air conditioner" . . . . . . . . . . . . . . . . . . . . 122
Air recirculation mode . . . . . . . . . . . . . . . . . . . . . 127
Air vents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
Alarm system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Alcantara . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 201
All-wheel drive Snow chains . . . . . . . . . . . . . . . . . . . . . . . . . . . 242
Towing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 256
Winter tyres . . . . . . . . . . . . . . . . . . . . . . . . . . . . 241
Alternator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 228
Ambient lighting . . . . . . . . . . . . . . . . . . . . . . . . . . 80
Anodized surfaces . . . . . . . . . . . . . . . . . . . . . . . . 199
Anti-lock brake system (ABS) . . . . . . . . . . . . . . . 154
Anti-theft alarm . . . . . . . . . . . . . . . . . . . . . . . . . . . 62 Trailer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
Anti-theft alarm system Anti-tow system . . . . . . . . . . . . . . . . . . . . . . . . . 62
False alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Interior monitoring . . . . . . . . . . . . . . . . . . . . . . . 62
Anti-theft bolts . . . . . . . . . . . . . . . . . . . . . . . . . . . 245
Anti-theft locking bolts . . . . . . . . . . . . . . . . . . . . 246
Anti-theft wheel locking bolts . . . . . . . . . . . . . . . 247
Anti-tow system . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Anti-trap function Electric windows . . . . . . . . . . . . . . . . . . . . . . . . . 71
Panoramic sliding sunroof . . . . . . . . . . . . . . . . . 74
Sun blind . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 74
Antifreeze . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
Armrests . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 97
Ashtray . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 118
Aspects to take into account before starting the vehicle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
ASR See "Brake assist systems" . . . . . . . . . . . . . . . 156
See "Brake assist" . . . . . . . . . . . . . . . . . . . . . . 155
Turning on and off . . . . . . . . . . . . . . . . . . . . . . 156
Assistance call . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53 287