2015 Peugeot RCZ fuel

63
RCZ_en_Chap03_confort_ed01-2015
SWITCHING THE SYSTEM OFF
F Turn the air flow control to the left until all of the indicator lamps go of
f.
This action switches off the air conditioning and the ventilation.
Temperature
related comfort is no longer guaranteed but a slight flow of
air

, due to the movement of the vehicle, can still be felt.
F Turn
the air flow dial to the right or press the
"AUT
O" button to
reactivate the system with the values set before it was switched off.
Avoid prolonged operation in interior air recirculation mode or
driving for long periods with the system off (risk of condensation
and
deterioration of the air quality).
8. Air intake / Air recirculation
F Press this button for recirculation of the interior air . The
indicator lamp in the button comes on.
Air recirculation enables the passenger compartment to be isolated from
exterior odours and smoke.
F

As soon as possible, press this button again to permit the intake of
outside air and prevent the formation of condensation.

The indicator
lamp on the button switches off.
9. Mono-zone / dual-zone
F Press this button to equalise the comfort value on the passenger's side with that on the driver's side (mono
zone).
The indicator lamp in the button comes on.
REAR SCREEN DEMIST -
DEFROST
SWITCHING ON
The rear screen demisting/defrosting can only operate when the engine
is running.
F

Press this button to demist/defrost the rear screen and (depending
on version) the door mirrors.

The indicator lamp associated with
the button comes on.
SWITCHING OFF
The demisting/defrosting switches off automatically to prevent an
excessive consumption of current.
F

It is possible to stop the demisting/defrosting operation before it
is switched of

f automatically by pressing the button again. The
indicator lamp associated with the button switches off.
If the engine is switched off before the demisting/defrosting is
switched off automatically, demisting/defrosting will resume next
time the engine is switched on.
F

Switch of
f the demisting/defrosting of the rear screen and door
mirrors as soon as appropriate as lower current consumption
results in reduced fuel consumption. The control button is located on the heating or air conditioning
system control panel.
3/
EASE OF USE and COMFORT

125
RCZ_en_Chap06_conduite_ed01-2015
It is only possible to change from one gear to another if the vehicle
speed and engine speed permit; otherwise, the gearbox will operate
temporarily in automatic mode.M and the gears engaged manually appear in succession in
the instrument panel.
If the engine speed is too low or too high, the gear selected
flashes
for a few seconds, then the actual gear engaged is
displayed.
It is possible to change from position
d

(automatic) to position M
(manual) at any time.
When the vehicle is stationary or moving very slowly, the gearbox
selects gear M1 automatically.
The sport and snow programmes do not operate in manual mode.
Invalid value during manual operation
This symbol is displayed if a gear is not engaged correctly
(selector between two positions).
STOPPING THE VEHICLE
Before switching off the engine, you can engage position P or N to
place the gearbox in neutral.
In both cases, apply the parking brake to immobilise the vehicle. If the selector is not in position P, when the driver's door is opened
or approximately 45 seconds after the ignition is switched off,
there is an audible signal accompanied by a message.
F

Return the selector to position
P
; the audible signal stops and
the message disappears.
OPERATING F AULT
When the ignition is on, the illumination of this warning lamp,
accompanied by an audible signal and a message in the
screen, indicates a gearbox malfunction.
In this case, the gearbox switches to emergency mode and is locked in
3rd gear. You may feel a substantial knock when changing from P to R
and from N to R. This will not cause any damage to the gearbox.
Do not exceed a speed of 60 mph (100 km/h), local speed restrictions
permitting.
Have

it

checked by a PEUGEOT

dealer or a qualified workshop.
This warning lamp may also come on if a door is opened.
There is a risk of damage to the gearbox:
-

if you press the accelerator and brake pedals at the same
time,
-


if you force the selector from position P

to another position
when
the battery is flat.
To reduce fuel consumption during a long period stationary with
the

engine running (traffic jam, etc.), place the gear selector in
position N

and apply the parking brake.
6/
DRIVING

126
RCZ_en_Chap06_conduite_ed01-2015
GEAR EFFICIENCY INDICATOR *
System which reduces fuel consumption by recommending the most
appropriate gear.
The system adapts its gear change recommendation according
to the driving conditions (slope, load,...) and the demands of the
driver (power, acceleration, braking,...).
The system never suggests:
- engaging
first gear,
-

engaging reverse gear
.
The information appears in the instrument panel in the form of an arrow.
OPERATION
Depending on the driving situation and your vehicle's equipment, the system may advise you to skip one (or more) gear(s).
You can follow
this instruction without engaging the intermediate gears.
The gear engagement recommendations must not be considered
compulsory.
In fact, the configuration of the road, the amount of traffic
and safety remain determining factors when choosing the best gear

.
Therefore, the driver remains responsible for deciding whether or not to\

follow the advice given by the system.
This function cannot be deactivated.
With an automatic gearbox, the system is only active in manual mode. On
vehicle fitted with a manual gearbox, the arrow may be
accompanied by the gear recommended. Example:
-

Y
ou are in third gear.
-
Y
ou press the accelerator pedal.
-
The system may suggest that you engage a higher gear
.
* Depending on engine.

127
RCZ_en_Chap06_conduite_ed01-2015
TYRE UNDER-INFLATION DETECTION
A pressure sensor is located in the valve of each of these tyres.
The system triggers an alert if a drop in pressure is detected in one or\

more tyres.This system does not avoid the need to check the tyre pressures
regularly and before a long journey.
Driving
with under-inflated tyres adversely affects road holding,
extends braking distances and causes premature tyre wear

,
particularly under arduous conditions (vehicle loaded, high speed,
long journey).
System which automatically checks the pressures of the tyres while
driving.
The system continuously monitors the pressures of the four tyres, as
soon as the vehicle is moving.
Driving with under-inflated tyres increases fuel consumption.
The tyre pressures for your vehicle can be found on the tyre
pressure label (see the "Identification markings" section).
The tyre pressures must be checked when the tyres cold (vehicle
stopped for 1 hour or after driving for less then 6 miles (10 km) at
moderate speed). Otherwise, add 0.3 bar to the values indicated
on the label.
Spare wheel
Don't forget to also check the tyre pressure of the spare wheel.
The alloy spare wheel also has a sensor.
The steel spare wheel does not have a sensor.
The

tyre

under-inflation

detection

system

is

an

aid

to

driving

which

does not replace the need for vigilance on the part of the driver

.
6/
DRIVING

139
RCZ_en_Chap07_verifications_ed01-2015
FUEL TANK
Fuel tank capacity: approximately 55 litres.
LOW FUEL LEVEL
R

EFUELLING
When the fuel tank minimum level is reached this warning
lamp comes on on the instrument panel, accompanied by an
audible signal and an alert message. When it first comes on
there remains approximately 5 litres

of fuel in the tank.
Until

sufficient fuel is added, this warning lamp appears every time
the ignition is switched on, accompanied by an audible signal and a
message. When driving, this audible signal and display of the alert
message

are repeated with increasing frequency as the fuel level drops
towards

"0".
Refuel as soon as possible to avoid running out of fuel.
If you run out of fuel (Diesel), refer also to the "Running out of fue\
l
(Diesel)" section.
A


label

affixed to the inside of the flap reminds you of the type of fuel to
be used depending on your engine.
Additions of fuel must be of at least 5 litres, in order to be registere\
d by
the fuel gauge. T

o fill the tank in complete safety:
F the engine must be switched off,
F
press the rear part of the flap, then raise it to open it,
F

turn the cap to the left,
F


remove the cap and hook it onto the clip located on the inside of the
flap,
F

fill the tank, but do not continue after the 3rd cut-off of the
pump; this could cause malfunctions.
Opening
the filler cap may create a noise a caused by an inrush
of air

. This vacuum is entirely normal, resulting from the sealing of
the fuel system.
7/
CHECKS

140
RCZ_en_Chap07_verifications_ed01-2015
FUEL USE d FOR PETROL ENGINES
The petrol engines are compatible with E10 bio-petrol (containing
10 % ethanol), conforming to European standards EN 228 and EN 15376.
E85 type fuels (containing up to 85 % ethanol) are reserved exclusivel\
y for
vehicles marketed for the use of this type of fuel (BioFlex vehicles).\
The
quality
of the ethanol must comply with European standard EN 15293.
FUEL USE d FOR dIESEL ENGINES
The Diesel engines are compatible with biofuels which conform to
current and future European standards (Diesel fuel which complies
with
standard EN 590 mixed with a biofuel which complies with
standard
EN 14214) available at the pumps (containing up to 7 % Fatty
Acid Methyl Ester).
B30 biofuel can be used in certain Diesel engines. However, this use,
even
occasional, requires strict application of the special servicing
conditions.

Contact a PEUGEOT

dealer or a qualified workshop.
The use of any other type of (bio)fuel (vegetable or animal oils, pur\
e
or diluted, domestic fuel...) is strictly prohibited (risk of damage t\
o the
engine and fuel system).
When

you

have

filled

the

tank:
F

put the cap back in place,
F

turn it to the right,
F
close

the

flap.
Freezing conditions
In these conditions, the filler flap may be jammed.
Opening the boot gives access to the flap, allowing it to be
released by hand.

143
RCZ_en_Chap07_verifications_ed01-2015
DIESEL ENGINE
The various caps and covers allow access for checking the levels of the various fluids, for replacing certain components and for priming the fuel system.
1.
Power steering reservoir
.
2.

Screenwash and headlamp wash reservoir
.
3.

Coolant reservoir
.
4. Brake
fluid reservoir.
5.

Battery / Fuses.
6.

Fusebox. 7. Air
filter.
8.

Engine oil dipstick.
9.

Engine oil filler cap.
10.

Priming pump.
11

.
Bleed screw
.
7/
CHECKS

144
RCZ_en_Chap07_verifications_ed01-2015
2.0 HdI ENGINE
F Fill the fuel tank with at least five litres of Diesel.
F
Open the bonnet.
F


If necessary
, unclip the style cover for access to the priming pump.
F

Slacken the bleed screw
.
F Squeeze
and release the priming pump repeatedly until fuel
appears in the transparent pipe.
F


T
ighten the bleed screw.
F

Operate the starter until the engine starts (if the engine fails to sta\
rt
at

the first attempt, wait around 15 seconds before trying again).
F

If the engine fails to start after a few attempts, operate the priming
pump again, then the starter

.
F

Put the style cover back in position and clip it in place, ensuring that\

it has clipped correctly

.
F

Close the bonnet.
RUNNING OUT OF FUEL (D IESEL )
If the engine does not start first time, don't keep trying but start the procedure again from the beginning.
On

vehicle fitted with HDi engines, the fuel system must be primed
manually if you run out of fuel; refer to the corresponding engine
compartment view

.