2015 Peugeot Partner Tepee light

146
Partner_2_VP_en_Chap07_Verification_ed02-2014
Bleeding water from the Diesel
filterManual gearbox
Have the level checked in accordance
with the manufacturer's servicing
schedule.
Only use products recommended
by P
euge O t
or products
of equivalent quality and
specification.
In order to optimise the operation
of units as important as the braking
system, P

euge O t
selects and of
fers
specific products.
In order to avoid damaging the
electrical units, high pressure washing
to clean the engine compartment is
strictly prohibited.
After washing the vehicle dampness,
or in winter, ice may form on the brake
discs and pads: braking efficiency may
be reduced. Make some light brake
applications to dry and de-ice the
brakes.
If this warning lamp comes
on, bleed the filter. Otherwise
bleed regularly each time the
engine oil is changed.
HDi engines use advanced
technology. All work requires
special training, which is assured
by a P
euge
O
t
dealer

.
Depending on country of sale.
to drain the water

, unscrew the bleed
screw located on the filter.
Operate until all of the water no longer
flows in the transparent pipe, then
tighten the bleed screw.
Checks

147
Partner_2_VP_en_Chap07_Verification_ed02-2014
FILLING WITH FUEL
Low fuel level
Filling
The fuel tank must be filled with the
engine off.
-
Open the fuel filler flap.
-


Insert the key
, then turn it a quarter
turn.
-

Remove the cap and hook it onto
the clip located on the inside of the
flap.
When fillin

g with fuel, a
mechanical system prevents
opening of the left-hand side door.
When the fuel filler flap is open, ensure
that no one tries to slide this door.
Once the flap has been closed, the
sliding side door may jam, push the
door to close it then open it.
When the minimum fuel tank
level is reached, this warning
lamp comes on.
You then have
approximately 8 litres of
fuel remaining. Fill up without delay to
avoid running out of fuel.
Never risk driving until you run out of
fuel as this may damage the emissions
control and injection systems. A label affixed to the inside of the flap
reminds you of the type of fuel to be
used.
You must fill with at least 5 litres of fuel
for it to be registered by the fuel gauge.
When the fuel filler cap is opened,
there may be a slight air suction noise.
t

his vacuum is entirely normal and is
due to the sealing of the fuel circuit.
When filling the fuel tank, do not
continue after the 3
rd cut-off of the
nozzle. t
his could cause malfunctions.
t

he capacity of the fuel tank is
approximately 60 litres.
-

After fillin

g the fuel tank, lock the
cap and close the flap.
Fuel used for petrol engines
the petrol engines are compatible
with e 10 bio-petrol (containing
10
% ethanol), conforming to e uropean
standards EN 228 and EN 15376.
e

85 type fuels (containing up to
85
% ethanol) are reserved exclusively
for vehicles marketed for the use of
this type of fuel (BioFlex vehicles).
t

he
quality of the ethanol must comply with
e

uropean standard e N 15293.
Fuel
CHeCKS
7

155
Partner_2_VP_en_Chap07_Verification_ed02-2014
Recommendations on storage
AdBlue® freezes at about -11°C
and deteriorates above 25°C. It is
recommended that bottles be stored in
a cool area and protected from direct
sunlight.
u

nder these conditions, the additive
can be kept for at least a year.
If the additive has frozen, can be used
once it has completely thawed out.
Never store bottles of AdBlue
® in
your vehicle. Procedure
Before topping-up, ensure that the
vehicle is parked on a flat and level
surface.
In wintry conditions, ensure that the
temperature of the vehicle is above
-11°C. Otherwise, by freezing, the
AdBlue
® cannot be poured into its tank.
Park your vehicle in a warmer area for
a few hours to allow the top-up to be
carried out.
F

Switch of
f the ignition and remove
the key.
-

For access to the
AdBlue
® tank,
open the filler flap; the AdBlue® filler
cap is located to the left of the fuel
filler cap
-

T

urn the blue cap a 6
th of a turn
anti-clockwise.
-

Lift of

f the blue cap.
AdBlue® additive
CHeCKS
7

160
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
1. Parking the vehicle
- the occupants must get out of the
vehicle and wait in a safe location.
-

If possible, park the vehicle on
level, stable and non-slippery
ground.
-


Apply the parking brake, switch
of

f the ignition and engage first or
reverse gear. -
Place a chock under the wheel
diagonally opposite the one to be
changed.
CHANGING A WHEEL
2. Tools
the tools are stowed in a storage area
closed by a flap under a front seat.
-

If necessary
, move the seat forward
to access the storage compartment
from the rear.
-

Remove the flap then take out the
jack and the tool carrier

.
-

Remove the tools needed from the
carrier

.
1.

Jack.
2.


Wheelbrace.
3.


Chock.
4.


Spanner for the Zenith roof bars
and rear lamps.
5.


Allow wheel trim removal tool.
6.

t
owing eye.
If the vehicle is fitted with a towbar

,
it is sometimes necessary to raise
the vehicle slightly to make it easier
to remove the spare wheel from its
carrier.
On certain types of ground and/
or if considerable loads are being
transported, call a P
euge
O
t
dealer or
a qualified workshop.
The jack and tools are specific to your
vehicle. Do not use them for other
purposes.
Changing a wheel

168
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
CHANGING A BULB
Type A
All glass bulb: pull gently
as it is fitted by pressure.
High pressure washing
Open the bonnet. to access the bulbs,
reach behind the headlamp unit.
Carry out the operations in reverse
order to refit each bulb and check that
the bonnet is closed securely
. Type C
Halogen bulb: release the
retaining spring from its
housing. Type B
Bayonet bulb: press
on the bulb then turn it
anticlockwise.
Halogen bulbs must be changed
with the headlamp off. Wait a few
minutes (risk of serious burns).
Do not touch the bulb directly with your
fingers, use lint-free cloths.
It is normal for condensation to form
inside the headlamps. Regular use of
the vehicle eliminates this misting.
t
he bulbs must be changed with
the ignition off or with the battery
disconnected. Wait approximately
3 minutes after changing the bulb
before reconnecting the battery.
Check that the lamps operate correctly
after each operation.
When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the lamps and their
edges to avoid damaging their coating
and seals.
Types of bulb
Various types of bulb are fitted to your
vehicle. to remove them:
T
ype D
Light emitting diode
(L
e D): for replacement
of the daytime running
lamps, contact a
P
euge O t
dealer or a
qualified workshop.
Changing a bulb

169
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
3. Direction indicators
T

ype B, PY21W - 21W (amber)
-

Remove the cover by pullin
g the
flexible rubber tab.
-
t
urn the bulb holder a quarter
turn anticlockwise.
-


Remove the bulb by pressing
it lightly while turning it
anticlockwise.
-


Change the bulb.
-


Ensure that the cover is refitted
correctly all round to assure
correct sealing.
2.

Sidelamps

T

ype A, W5W - 5W
-

Remove the cover by pullin

g the
flexible rubber tab.
-

Remove the bulb holder fitted by
pressure by pullin

g the connector.
-

Change the bulb.
-


Ensure that the cover is refitted
correctly all round to assure
correct sealing.
FRONT LAMPS
1. Dipped / Main beam headlamps
T

ype C, H4 - 55W
-

Remove the centre cover by
pullin

g the flexible rubber tab.
-

Disconnect the electrical
connector

.
-

Release the retaining tab.
-


Change the bulb taking care
to align the metal part with the
grooves on the lamp.
-


Reposition the retaining tab.
-


Ensure that the cover is refitted
correctly all round to assure
correct sealing.
Changing a bulb
QuICK HeLP
8

171
Partner_2_VP_en_Chap08_Aide-rapide_ed02-2014
REAR LAMPS
this procedure requires the use of
the spanner supplied with the tools for
changing a wheel.
When refitting, take care to
reposition the tabs and the supply
wire correctly to avoid trapping the
wire.
After changing the rear direction
indicator bulb, the reinitialisation time is
above 2 minutes. - Move aside the 4 tabs then extract
the bulb holder
.
-

Remove the faulty bulb by
pressing it lightly while turning it
anticlockwise.
-


Change the bulb.
When removing the lamp unit:
-


with tailgate, pull the lamp unit
towards the centre of the vehicle,
-


with hinged doors, pull the lamp
unit towards you.
For more information concerning the
bulbs, refer to the "

types of bulb".
1.

Brake lamps / sidelamps




T

ype B, P21/5W - 21/5W
2.

Direction indicators




T

ype B, PY21W - 21W (amber)
3.

Reversing lamps




T

ype B, P21W - 21W
4.

Foglamps




T

ype B, P21W - 21W
High pressure jet washing When using this type of washing
on stubborn dirt, do not persist on
the headlamps, the other lamps
and their edges to avoid damaging
their coating and seals. Chapter 9, "Changing a wheel"
section.
-

Identify the faulty bulb, then open
the rear doors to 180°. Chapter 3, "Access" section.
-


Remove the two fixing bolts using
the spanner provided.
-


Pull the lamp unit from the outside.
-


Holding the lamp, disconnect the
electrical connector

.
Changing a bulb
QuICK HeLP
8

184
Partner_2_VP_en_Chap09_Caract-technique_ed02-2014
ENGINE CHARACTERISTICS
the engine characteristics (capacity,
maximum power , maximum power
speed, fuel, CO
2 emissions...) for your
vehicle are given in the registration
document.
t

hese characteristics correspond
to the values type-approved
on a test bed, under conditions
defined in European legislation
(Directive

1999/99/ e C).
For more information, refer to the
manufacturer's website or sales
brochure for the model. Contact
a PEUGEOT dealer or a qualified
workshop.
WEIGHTS AND TOWED LOADS
the weights and towable loads for your
vehicle can be found on the vehicle's
registration certificate.
t

hese values, expressed in kg, are
laos present on the manufacturer's
plate or label.
t

he kerb weight is equal to the weight
without load + driver (75 kg) + fuel tank
filled to 90%.
t

he gt W and towed load values
indicated are valid up to a maximum
altitude of 1000 metres.
t

he value of
the towed load mentioned must be
reduced by 10 % for each additional
1000 metres.
With load transfer, the braked trailer
weight can be increased, on condition
that the equivalent of this load is
removed from the vehicle so that the
gt

W is not exceeded. High ambient temperatures
may result in a reduction in the
performance of the vehicle in
order to protect the engine. When the
ambient temperature is higher than
37
°C, limit the towed weight.
towing with a lightly loaded
vehicle can adversely af

fect road
holding.
towing a trailer increases braking
distances.
When towing, the maximum permitted
speed is reduced (comply with the
legislation in force in the country).
t he recommended nose weight is
the downward force on the towball
(removable with or without tools).
GVW: gross vehicle weight, the
maximum authorised weight.
GTW: gross train weight, the maximum
weight for vehicle plus trailer.
Refer to chapter 9, "Identification
markings" section.
In each country, it is imperative that
the towed loads authorised by local
legislation are complied with. To find
out your vehicle's towing capacities
and its gross train weight, consult a
P
euge O t
dealer
.
Weights