2015 PEUGEOT BOXER brake

129
used products
Avoid prolonged contact of used oil or fluids
with the skin.
Most of these fluids are harmful to health or
indeed very corrosive.
Do not discard used oil or fluids into sewers
or onto the ground.
take used oil to a PeugeOt dealer or
a qualified workshop (France) or to an


authorised waste disposal site.
LEVELS
these regular maintenance operations
will keep your vehicle in good running
order
. Ask for advice at a P
eugeOt dealer
or consult the warranty and maintenance


record contained in the handbook pack.
to maintain the reliability of engines and
emission control systems, the use of


additives in engine oil is prohibited.
changing the brake fluid
the brake fluid must be changed at
the intervals stated, according to the
manufacturer's servicing schedule.
use fluids recommended by the


manufacturer, which fulfil DO
t4 standards.
the level must be between the

MI
n and

MA
x marks on the reservoir

.
If fluid has to be added frequently, this
indicates a failure which must be checked by
a P
eugeOt dealer or a qualified workshop
as soon as possible.
If you have to remove/refit the engine


styling cover, handle it with care to
avoid damaging the fixing clips.
dipstick
there are two marks on

the dipstick:
oil change
It is imperative that this is carried out at the


intervals specified in the manufacturer's
servicing schedule. Ask for advice at at
P
eugeOt dealer.
Remove the dipstick before filling.
Check the level after filling (never exceed


the maximum mark).
Screw the cap back onto the sump before
closing the bonnet.
Viscosity selection
When topping-up, the oil selected must meet
the manufacturer's requirements.
Warning lamps
Checking by means of the warning
lamps on the instrument panel is
described in the "Ready to set off -
Instruments and controls" section.
A
= maximum
If you fill past this mark,
contact a P
eugeOt
dealer or a qualified
workshop.
B = minimum
Never allow the level to fall


below this mark.
oil level
Check the level regularly and top up
between changes.
the maximum

consumption is 0.5 litre per 600 miles
(1 000
km). Check the level with the vehicle


level, engine cold, using the dipstick.
7
CHeCKS
Levels and checks

132
Manual gearbox
Have the level checked in accordance with
the manufacturer's servicing schedule.
Good practiceoil filter
Brake pads
Brake pad wear depends on the style of
driving, in particular for vehicles which are
used in town, over short distances. It may
be necessary to check the thickness of the
pads, even between services.
Brake disc wear
For any information on checking the brake
disc wear, contact a P
eugeOt dealer or a
qualified workshop.
Parking brake
Where the parking brake travel is too great
or there is a reduction in the performance
of the system, the parking brake should be
adjusted, even between services.
Have the system checked by a P
eugeOt
dealer or a qualified workshop.
If this warning lamp comes on,
have the brake pad wear checked


by a P
eugeOt dealer or a
qualified workshop. In order to avoid damaging the


electrical units, we strongly advise you
not to use high pressure washing to clean
the engine compartment.
After washing the vehicle dampness, or in
winter, ice may form on the brake discs and
pads: braking efficiency may be reduced.
Make some light brake applications to dry
and de-ice the brakes. Only use products recommended by
P
eugeOt or products of equivalent quality
and specification.
In order to optimise the operation of units as

important as the braking system, P
eugeOt
selects and offers specific products.
Change the filter regularly

, in accordance
with the manufacturer's servicing schedule.
Levels and checks

146FusesA (amps) Allocation
12 7.5Right-hand dipped headlamp
13 7.5Left-hand dipped headlamp
31 5
engine compartment control unit relay - Dashboard control unit relay (ig\
nition switch +)
32 7.5Cabin lighting (battery +)
33 7.5Battery check sensor on Stop & Start version (battery +)
34 7.5Minibus interior lighting - Hazard warning lamps
36 10Audio system -

Air conditioning controls - Alarm -
tachograph - Battery cut-off control unit -

Additional heating programmer (battery +)
37 7.5Brake lamp switch -
third brake lamp Instrument panel (ignition +)
38 20Central door locking (battery +)
42 5ABS control unit and sensor -

ASR sensor - DSC sensor - Brake lamp switch
43 20Windscreen wiper motor (ignition switch +)
47 20Driver's electric window motor
48 20Passenger's electric window motor
49 5Parking sensors control unit - Audio system - Steering mounted controls - Centre and side switch panels\
-
Auxiliary switch panel - Battery cut-off control unit (ignition switch +)
50 7.5Airbags and pre-tensioners control unit
51 5
tachograph - Power steering control unit - Air conditioning - Reversing lamps - W

ater in Diesel sensor -
Air flow sensor (ignition switch +)
53 7.5Instrument panel (battery +)
89 -Not used
90 7.5Left-hand main beam
91 7.5Right-hand main beam
92 7.5Left-hand front foglamp
93 7.5Right-hand front foglamp
Failed fuse

153
rear lamps
Carry out these operations in reverse order
to fit the new bulb.
1.
Brake lamps
type B, P21W - 21W
2.
Brake/sidelamps
type B, P

21/5W - 21W and 5W
3.
direction indicators
type B, PY

21W - 21W
4.
reversing lamps
type A, W16W - 16W
5.
Foglamp
type A, W16W - 16W -
Identify the failed bulb then open the
rear doors.
-
Remove the corresponding access cover
by removing the seven fixing screws

(van) or
Remove the corresponding access cover
by pulling on its grip to unclip it (combi).
-
Disconnect the electrical connector by
pressing on its central tongue.
-
Remove the two fixing nuts of the lens.
-
Pull the lens from the outside. -
Remove the six bulb holder fixing
screws.
-
Spread the three retaining tongues and
remove the bulb holder from its housing.
-
Change the bulb.
For more information on the bulbs,
refer to the table "
types of bulb or
lamp".
QuICK HeLP
8
Failed bulb or lamp

154
third brake lamp
type A, W5W - 5W (x 4)
-
Remove the two lamp fixing screws.
-
Remove the lamp by pulling it towards
you.
number plate lamps
type c, C5W - 5W
-
Press the point, indicated by the arrow,

then remove the plastic lens.
-
Remove the failed bulb by moving aside
the two contacts.
-
With the new bulb in place, ensure that
it is secured correctly between the two


contacts.
-
Replace the plastic lens and press on it
to lock it in place. -
Remove the bulb holder by squeezing
the two tabs.
-
Remove the failed bulb by pulling it out.
-
Change the bulb.
Failed bulb or lamp

156
Parking the vehicle
Where possible, park the vehicle on level,
stable and non-slippery ground.
Apply the parking brake, switch off the
ignition and engage first gear.
Wear a high visibility vest and position the
warning triangle on the road.
You must ensure that the occupants get out
of the vehicle and wait in a safe location.
tools
these are stowed in a box located under the
front passenger seat.
-


t
urn the button a quarter of a turn then
pull the box.
-
After use, press the button then turn it a
quarter of a turn to secure the box.
A.
Long socket.
B.
Bar

.
c. Jack.
d. Wheelbrace.
E.
Screwdriver (handle and bits).
F.
Removable towing eye.
cHAnGInG A WHEELPneumatic suspension
If you vehicle is fitted with this system,
you must first activate vehicle lifting mode.
Press the two controls simultaneously for
at least 5 seconds; their indicator lamps
come on.
this mode is deactivated automatically after


changing a wheel, once the speed of the
vehicle has exceeded 3 mph (5 km/h).
the jack and the tool kit are specific to


your vehicle. Do not use them for other
purposes.
Never go underneath a vehicle supported
only by a jack (use an axle stand).
Puncture

161
PuncturE rEPAIr KItrepairing the tyre
- Apply the parking brake.
-

u
nscrew the tyre valve cap, remove the

filling hose B and screw the ring E onto
the valve. -
Start the engine.
-
Insert the connector G into the nearest
power socket on the vehicle.
-
Switch on the compressor by placing the
switch F in position

"I" (on).
-
Inflate the tyre to a pressure of 5 bar.
to obtain a more accurate reading, you are
advised to check the pressure value on the


pressure gauge H , with the compressor off.
-
Check that the switch F on the


compressor is in position "0" (off).this temporary puncture repair kit stowed

in a bag located in one of the front door
pockets.
It consists of:
-
a cartridge A , containing the sealant


fluid, equipped with:
●
a filling hose B ,
●
a sticker c indicating "max. 80 km/h",
which the driver must af

fix in full view
(on the dashboard) after repairing
the
tyre,
-
a quick guide to use of the repair kit,
-
a compressor d equipped with a
pressure gauge and unions,
-
adaptors, for the inflation of various
items.
QuICK HeLP
8
Puncture

163
toWInG
t
owing the vehicle
the removable towing eye is located in the
tool box under the front passenger seat.
unclip the cover using a flat tool.
Screw the removable towing eye in fully

.
Attach the approved towing arm to to the
removable towing eye.
Place the gear lever in neutral.
towing another
vehicle
the fixed towing eye is located on the right
below the bumper.
Attach the approved towing arm to the fixed

eye.
Failure to observe this requirement
may result in damage to certain braking
components and the lack of some braking
assistance systems when the engine is
re-started.
General recommendations
Observe the legislation in force in your
country.
ensure that the weight of the towing vehicle


is higher than that of the towed vehicle.
the driver must remain at the wheel of the


towed vehicle and must have a valid driving
licence.
When towing a vehicle with all four wheels
on the ground, always use an approved
towing arm; rope and straps are prohibited.
the towing vehicle must move of

f gently.
When towing a vehicle with the engine off,
there is no longer any power assistance for
braking or steering.
In the following cases, you must always call
on a professional recovery service:
-
vehicle broken down on a motorway or
fast road,
-
four-wheel drive vehicle,
-
when it is not possible to put the
gearbox into neutral, unlock the


steering, or release the parking brake,
-
towing with only two wheels on the
ground,
-
where there is no approved towing arm
available...
QuICK HeLP
8
Being towed or towing