2015 Peugeot 208 mileage

26
208_en_Chap01_instruments-bord_ed01-2016
Servicing
The vehicle's odometer is displayed in area A
of the display screen and the trip recorder in
area B. -
i t remains displayed if the service is
overdue,
The service indicator does not appear if it is
more than 2 000 miles (3 000 km) before the
next service is due.
For BlueHDi Diesel versions only
(depending on the country of sale), the
degree of deterioration of the engine oil
is also taken into account.
This is a countdown between the intervals
given in the manufacturer's service schedule.
It is calculated from the last reset of
the service indicator, according to the
mileage covered and the time elapsed
since the last service. The service indicator appears when
approaching a servicing point:
-

i
t indicates the distance before the next
service is due,
-

i
t displays the servicing interval in
two


ways,
Instruments

28
208_en_Chap01_instruments-bord_ed01-2016
Retrieving the service
information
You can access the service information at any
time.
F
P
ress the trip distance recorder reset
button.
T

he service information is displayed for a
few seconds, then disappears.
With the trip mileage displayed, press the
button for a few seconds.
Trip recorder reset
If you have to disconnect the battery
following this operation, lock the vehicle
and wait at least 5 minutes for the reset
to be registered.
Resetting the service indicator
After each service, the service indicator must
be reset to zero.
If you have carried out the service on your
vehicle yourself:
F
s
witch off the ignition,
F

p
ress and hold the trip distance recorder
reset button,
F

s
witch on the ignition; the distance recorder
display begins a countdown,
F

w
hen the display indicates "=0" , release
the button; the spanner disappears.
AdviceFor BlueHDi Diesel versions, this
alert is also accompanied by the fixed
illumination of the Service warning
lamp, when the ignition is switched on.
The distance remaining may be
weighted by the time factor, depending
on the driving conditions.
Therefore, the spanner may also come
on if you have exceeded the period
since the last service, indicated in the
manufacturer's service schedule.
For BlueHDi Diesel versions, the
spanner can also come on early,
according to the degree of deterioration
of the engine oil. The deterioration
of the engine oil depends on the
conditions in which the vehicle is used.
Instruments

Driving
138
208_en_Chap06_conduite_ed01-2016
Be vigilant when modifying the cruise
control setting by pressing and holding,
as the speed of your vehicle may
increase or decrease quickly.
Do not use the cruise control on
slippery roads or in heavy traffic.
On a steep descent, the cruise control
will not be able to prevent the vehicle
from exceeding the registered speed.
The cruise control system cannot in
any circumstances replace the need
to observe speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming of the
pedals:
-
e
nsure that the mat is positioned
and secured to the floor correctly,
-

n
ever fit one mat on top of another.
Operating fault
The registered speed setting is erased, then
replaced by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Switching off the function
Without using the accelerator
Using the accelerator
To register a speed lower than the previous
setting: -
P
ress the SET + button.
A short press increases the speed setting by 1 mph (km/h).
Pressing and holding increases the setting in steps of
5
mph (km/h).
- Accelerate beyond the registered speed to the new desired speed.
-

P

ress the SET + or SET - button.
-

P

ress the SET - button.
A short press decreases the speed setting by 1 mph (km/h).
Pressing and holding decreases the setting in steps of
5 mph (km/h).
- Place the thumbwheel at the "0" position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.

Practical information175
208_en_Chap07_informations-pratiques_ed01-2016
Advice
While the quantity of AdBlue® in the additive
t
ank is sufficient, no information is displayed.
On the other hand, once the additive level
drops to the quantity needed for a range of
1 500 miles (2 400 km) driving, you are warned
by different temporary signals (warning lamp,
message, audible signal).
When the AdBlue
® tank is empty, restarting
becomes impossible. Different levels of alert are triggered according
to the remaining driving range threshold.
You will be informed as each mileage threshold
is reached and the alerts will change from
temporary to permanent.
-
T he 1st alert is triggered at a remaining
driving range of 1 500 miles (2 400 km).
-

T

he 2
nd alert is triggered at a remaining
driving range of 375 miles (600 km).
Up to 0 miles, at which point it will be
impossible to restart the engine after a stop.
Range indicators
It is strongly recommended that you do
not wait for the successive alerts before
topping-up the AdBlue
® tank, but do this
as soon as possible.
Driving range
Press this button to display the information.
With the touch screen:
If the range is greater than 3 100 miles
(5 000 km), a range value is not given. -

s
elect the "Driving assistance"
menu,
-
s

elect "Diagnostic",
-

s
elect CHECK.
7