2015 Peugeot 208 tailgate

Access43
208_en_Chap02_ouvertures_ed01-2016
Boot
Using the key.
Using the remote control.
Opening Closing
F Lower the tailgate using the interior grab
handle.
F

I
f necessary, press down on the tailgate to
fully close it.
With the engine running , this is
signalled by:
-

t
his warning lamp coming on,
-

a
n alert message displayed for a
few seconds.
With the vehicle moving (speed higher than
6 mph (10 km/h)), this is signalled by:
-

t
his warning lamp coming on,
-

a
n alert message displayed for a
few


seconds,
-
an

audible signal.
Boot still open
F After unlocking the boot or the vehicle, press the opening control which releases
the tailgate, and then guide it open.
Tailgate release
System for mechanical unlocking of the boot in
the event of a central locking malfunction.
Unlocking
F Fold back the rear seats to gain access to the lock from inside the boot.
F

I
nsert a small screwdriver into hole A of the
lock to unlock the tailgate.
Advice
2

Driving
146
208_en_Chap06_conduite_ed01-2016
Reversing camera
The reversing camera function may be
completed with parking sensors. The reversing camera cannot in any
circumstances be a substitute for
vigilance on the part of the driver.
The superimposed representation of guide
lines helps with the manoeuvre.
They are represented by lines marked "on
the ground" and do not allow the position of
the vehicle to be determined relative to tall
obstacles (for example: other vehicles, ...).
Some deformation of the image is normal.
High pressure jet washing
When washing your vehicle, do not
direct the lance within 30 cm of the
camera lens.
The reversing camera is activated automatically
when reverse gear is engaged.
The image is displayed in the touch screen.
The blue lines represent the general direction
of the vehicle (the difference corresponds to
the width of your vehicle without the mirrors).
The red lines represent a distance of about
30 cm beyond the edge of your vehicle's rear
b u m p e r.
The green lines represent distances of about 1
and 2 metres beyond the edge of your vehicle's
rear bumper. Opening the tailgate causes the display
to disappear.
Clean the reversing camera regularly
using a soft, dry cloth.

Practical information179
208_en_Chap07_informations-pratiques_ed01-2016
Filling
F Pour the contents of the bottle into your vehicle's AdBlue® tank.
Important : if your vehicle's AdBlue
®
tank is completely empty - which is
confirmed by the alert messages and
the impossibility of starting the engine,
you must add at least 3.8 litres (so two
1.89 litre bottles).
If any additive is split or splashed, wash
immediately with cold water or wipe with
a damp cloth.
If the additive has crystallised, clean it
off using a sponge and hot water.
F

W

ipe away any spillage around the tank
filler using a damp cloth.
Closing
F Refit the blue cap to the tank and turn it a 6th of a turn clockwise, to its stop.
F
R
efit the black cap and turn it a quarter of
a turn clockwise without pressing. Ensure
that the indicator on the cap lines up with
the indicator on the support.
F

D

epending on equipment, return the spare
wheel and/or the storage box to the bottom
of the boot.
F

R

efit the boot carpet and close the tailgate.
Access
F For access to the AdBlue® tank, raise the
boot carpet then, depending on equipment,
lift out the spare wheel and/or the storage
box.
Opening
F Without pressing, turn the black cap a quarter turn anti-clockwise and lift it off.
F

T
urn the blue cap a 6
th of a turn anti-
clockwise.
F

L

ift off the cap.
7

In the event of a breakdown201
208_en_Chap08_cas-de-panne_ed01-2016
Changing the third brake lamp
bulbs
F Unscrew the fixing pins on each side of the lamp, without removing them completely.
F

P
ush on the screws to unclip the lamp.
F

D
isconnect the lamp connector.
F

R
emove the lamp from the outside.
F

T
urn the bulb holder which corresponds
to the faulty bulb one quarter of a turn and
remove it.
F

P
ull the bulb and change it.
To refit, carry out these operations in reverse
o r d e r.
Number plate lamps
To facilitate the removal of the lamp, carry out
this operation with the tailgate half open.
F

I
nsert a thin screwdriver into the lens
cutout.
F

P
ush it outwards.
F

R
emove the lens.
F

C
hange the faulty bulb.
To refit, press on the lens to clip it in place. Access is by passing a hand under the bumper.
F
T urn the bulb holder a quarter of a turn and
pull it out.
F

D
isconnect the connector on the bulb
h o l d e r.
F

P
ull the bulb out and change it.
To refit, carry out these operations in reverse
o r d e r.
You can also contact a PEUGEOT dealer or a
qualified workshop for the replacement of these
bulbs.
Changing a foglamp bulb
8