2015 Peugeot 208 ignition

Driving
128
208_en_Chap06_conduite_ed01-2016
Sport programme
This special programme completes the
automatic operation of the gearbox in certain
circumstances. F

P
ress the "S" button once the
engine is running.
The gearbox automatically operates in a way
best suited to dynamic driving.
S appears in the instrument panel.
Snow programme Return to normal automatic
operation
Switching off - Parking
You risk damaging the gearbox:
F
i f you press the brake and
accelerator pedals at the same
time,
F

i
f you force the movement of the
lever from position P to another
position with a flat battery.
To reduce fuel consumption during
prolonged stops with the engine running
(traffic jams...), position the gear lever
at N and apply the parking brake.
If the lever is not in position P
, a
message appears in the screen
on opening the driver's door or
approximately 45 seconds after
switching off the ignition.
F

P

lace the lever at position P ;
the


message disappears.
On flooded roads or when crossing a
ford, drive at walking pace. With the ignition on, illumination of
this warning lamp, accompanied
by an audible signal and an alert
message in the screen, indicates of
gearbox fault.
In this case, the gearbox goes into back-up
mode by staying in 3rd gear. You may then
notice a pronounced jerk when changing from
P to R and from N to R . This jerk does not
present any risk to the gearbox.
Do not exceed 62 mph (100 km/h) while
keeping to local speed limits.
Contact a PEUGEOT dealer or a qualified
workshop as soon as possible.
This special programme completes the
automatic operation and makes it easier to
move off and make progress in conditions of
poor grip. Before switching off the engine.
F

M

ove the lever to position P or N
.
F

A

pply the parking brake.
F

Imm

obilise the vehicle.
F

P

ress the T button, once the
engine has started.
The gearbox adapts its operation to driving on
slippery surfaces.
T appears in the instrument panel. F

P

ress the button again at any time
to quit the Sport programme and
return to auto-adaptive mode.

Driving
132
208_en_Chap06_conduite_ed01-2016
For your comfort, during parking
manoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
The Stop & Start system does not affect
the functionality of the vehicle, such as
for example, braking, ...
Never refuel with the engine in STOP
mode; you must switch off the ignition
with the key. A time counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition is
switched on with the key.
Advice
S TA R T m o d e
Special casesAs a safety measure and for your comfort,
START mode is invoked automatically when:
-
y

ou open the driver's door,
-
y

ou unfasten the driver's seat belt,
-
s

ome special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed for control of a system.
The "ECO" warning lamp flashes for
a few seconds, then goes off.
This operation is perfectly normal.
With a manual gearbox
:
-

C

lutch pedal depressed.
With an electronic / automatic gearbox :
-

G

ear lever in position A / D or M .
-
B

rake pedal released. The "ECO"
lamp goes off and the
engine restarts.
or
-

G

ear lever in position N .
-
B

rake pedal released.
-

T

hen gear lever in position A / D or M .
or
-
R

everse gear engaged.
With a manual gearbox in STOP mode,
if you engage a gear without fully
depressing the clutch pedal, a message
is displayed asking you to fully depress
the clutch pedal so that the engine can
restart.

Driving133
208_en_Chap06_conduite_ed01-2016
Manual deactivation
- Press.
- T he indicator lamp in the control remains
on.
-

A m
essage is displayed.
If the vehicle is stationary in Stop mode, the
engine immediately restarts.
Manual reactivation
Driving on flooded roads
Before driving through a flooded road,
it is strongly recommended that you
deactivate the Stop & Start system.
For more advice on driving, particularly
on flooded roads, refer to the
corresponding section.
Opening the bonnet
Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid the risk of injury related
to an automatic change to START
mode.
In some circumstances, such as maintaining
a comfortable temperature in the passenger
compartment, it may be useful to deactivate
Stop & Start.
The system can be deactivated at any time,
once the ignition is on.
This control switches off the Stop & Start
system.
Operating fault
The Stop & Start system requires a
12 V battery of special specification and
technology.
All work on this type of battery must
be done by a PEUGEOT or a qualified
workshop.
For more information on the 12 V
battery, refer to the corresponding
section.
In the event of a fault with the system, the
"ECO OFF" switch warning lamp flashes then
comes on continuously.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
In the event of a fault in STOP mode, the
vehicle may stall. All of the warning lamps
come on. It is then necessary to switch off
the ignition and start the engine again using
t h e


key.
-

Press.
-

T

he indicator lamp in the control goes off.
-

A c

onfirmation message is displayed.
If the engine is in STOP mode, it then
restarts.
The Stop & Start

system is reactivated
automatically every time the ignition is
switched on.
6

Driving135
208_en_Chap06_conduite_ed01-2016
On / Pause
Flashing of the speed setting
Exceeding the registered
limit speed
Pressing the accelerator pedal to exceed
the registered speed will not have any effect,
unless you press the pedal firmly past the
point of resistance .
The speed limiter is deactivated temporarily
and the registered speed setting flashes,
accompanied by an audible signal.
To return to normal operation of the speed
limiter, reduce your speed to below the
registered speed setting. It flashes:
-

a
fter forcing the accelerator pedal past the
point of resistance,
-
w
hen the limiter cannot prevent the speed
of the vehicle increasing, because of the
profile of the road or when going down a
steep hill,
- u nder sharp acceleration.
Operating fault
The registered speed is erased, then replaced
by three dashes.
Have the system checked by a PEUGEOT
dealer or a qualified workshop.
The last speed registered stays in memory.
A first press on this button switches the speed
limiter on, a second press pauses it (OFF)
.
F

P

lace the thumbwheel at the 0 position or
switch off the ignition to stop the system.
Switching off the function
In no circumstances can the speed
limiter replace the need to observe
speed limits or the need for vigilance on
the part of the driver.
Be aware of the effect of the profile
of the road and sharp acceleration,
maintaining control of the vehicle at all
times.
To avoid any risk of inter ference below
the pedals:
-

e
nsure that the mat and its
fixings on the floor are positioned
c o r r e c t l y,
-

d
o not fit one mat on top of another.
6

Driving
138
208_en_Chap06_conduite_ed01-2016
Be vigilant when modifying the cruise
control setting by pressing and holding,
as the speed of your vehicle may
increase or decrease quickly.
Do not use the cruise control on
slippery roads or in heavy traffic.
On a steep descent, the cruise control
will not be able to prevent the vehicle
from exceeding the registered speed.
The cruise control system cannot in
any circumstances replace the need
to observe speed limits or the need for
vigilance on the part of the driver.
To avoid any risk of jamming of the
pedals:
-
e
nsure that the mat is positioned
and secured to the floor correctly,
-

n
ever fit one mat on top of another.
Operating fault
The registered speed setting is erased, then
replaced by three dashes.
Have it checked by a PEUGEOT dealer or a
qualified workshop.
Switching off the function
Without using the accelerator
Using the accelerator
To register a speed lower than the previous
setting: -
P
ress the SET + button.
A short press increases the speed setting by 1 mph (km/h).
Pressing and holding increases the setting in steps of
5
mph (km/h).
- Accelerate beyond the registered speed to the new desired speed.
-

P

ress the SET + or SET - button.
-

P

ress the SET - button.
A short press decreases the speed setting by 1 mph (km/h).
Pressing and holding decreases the setting in steps of
5 mph (km/h).
- Place the thumbwheel at the "0" position:
cruise control mode is deselected. The
display returns to the total mileage recorder.
After switching off the ignition, all registered
speed settings are lost.

Driving
142
208_en_Chap06_conduite_ed01-2016
The collision can be automatically
avoided if the speed difference between
your vehicle and the one ahead is not
more than 9 mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
seriousness of the accident by lowering
the speed of impact.
The automatic braking triggered:
-

c

an be even more effective if the driver
presses the brake pedal more firmly,
-

m

ay stop the vehicle, holding the brakes on
for 1.5 seconds when stationary to allow
the driver time to take back control of the
vehicle,
-

m

ay cause the engine to stall,
-

m

ay give rise to a pumping noise, due to
the pressurisation of the braking system.
Touch screen
Press " MENU" to display the " MAIN
MENU ".
Select " Driving ".
Select " Secondary page ".
Select " Vehicle settings ".
Select the " Driving assistance " tab.
Check the " Automatic emergency
braking activated " box.
Activation
Confirm. Deactivation
Check the "
Automatic emergency braking
deactivated " box.
The last selection remains in memory when the
ignition is switched off.
If the automatic emergency braking function is
deactivated, following each start a temporary
message will be displayed to signal this, once a
speed threshold (6 mph - 10 km/h) is exceeded.
To deactivate :
- F ollowing an impact to the windscreen
close to the sensor.
-

W
hen towing a trailer.
-
W

hen the vehicle is being towed.
-

W
hen the vehicle is about to cross a toll
payment barrier.
-

W
hen the vehicle is going through an
automatic car wash.

Driving
150
208_en_Chap06_conduite_ed01-2016
In bad weather and in winter, ensure
that the sensors are not covered by
road dirt, ice or snow.
In the event of a fault, have the system
checked by a PEUGEOT dealer or a
qualified workshop.
If the system is deactivated during a
manoeuvre, the driver should reactivate
it manually to repeat the measurement. If the lateral distance between your vehicle
and the space is too great, the system may
not be able to measure the space.
Anything projecting beyond the envelope
of the vehicle (long or wide load) is not
taken into account by the Park Assist
system during a manoeuvre.
Deactivation
A message is displayed in the screen.
The driver then takes back control of the
vehicle's steering.
The system is deactivated automatically:
-
o
n switching off the ignition,
-

i

f the engine stalls,
-

i

f no manoeuvre is started within 5 minutes
of selection of the type of manoeuvre,
-

a

fter a prolonged stop of the vehicle during
a manoeuvre,
-

i

f the road wheel anti-spin regulation (ASR)
is triggered,
-

i

f the speed of the vehicle exceeds the
stated limit,
-

w

hen the driver interrupts movement of the
steering wheel,
-

i

f the driver presses the Park Assist
control,
-

i

f correct positioning of the vehicle is not
possible (too many manoeuvres needed to
insert or extract the vehicle),
-

i

f the driver's door is open,
-

i

f one of the front wheels encounters an
obstacle.
Switching off
The system is switched off automatically:
- w hen towing a trailer,
-

i
f the driver's door is opened,
-

i
f the speed of the vehicle is above 42 mph
(70 km/h).
To switch the system off for a prolonged period,
contact a PEUGEOT dealer or a qualified
workshop. The indicator lamp in the control flashes for a
few seconds. If the problem occurs while using
the system, the indicator lamp goes off.
These warning lamps
indicate a fault with the power
steering.
Contact a PEUGEOT dealer or a qualified
workshop. This warning lamp is displayed in the
instrument panel and/or a message
appears in the screen, accompanied
by an audible signal (short beep).

Driving153
208_en_Chap06_conduite_ed01-2016
Reinitialisation
It is necessary to reinitialise the system every
time one or more tyre pressures are adjusted,
and after changing one or more wheels.Before reinitialising the system, ensure
that the pressures of the four tyres are
correct for the use of the vehicle and in
line with the recommendations on the
tyre pressure label.
The under-inflation alert can only
be relied on if the reinitialisation of
the system has been done with the
pressures in the four tyres correctly
adjusted.
The under-inflation detection system
does not give a warning if a pressure is
incorrect at the time of reinitialisation. F

W
ith the ignition on and the
vehicle stationary, press this
button for about 3 seconds then
release it, an audible signal
confirms the reinitialisation.
The new pressure settings registered
are considered to be reference values
by the system.
Reinitialisation of the system is done with the
ignition on and the vehicle stationary.
F

P
ress "Under-inflation
initialisation ".
From the "
Driving assistance " menu
of the touch screen:
F

C
onfirm the instruction by pressing "Ye s",
an audible signal and a message confirm
the reinitialisation.
Operating fault
The flashing and then fixed illumination of the
under-inflation warning lamp accompanied
by illumination of the Service warning lamp
indicates a fault with the system.
In this case, under-inflation monitoring of the
tyres is no longer assured.
Have the system checked by a PEUGEOT
dealer or a qualified workshop.
Touch screen Screen A
Before doing anything to the system,
the pressures of the four tyres must be
checked and the system reinitialised.
6