2015 Peugeot 208 Menu

86
With the dipped or main beam headlamps
on, this function makes use of the beam from
the front foglamp to illuminate the inside of a
bend, when the vehicle speed is below 25 mph
(approximately 40 km/h) (urban driving, winding
road, intersections, parking manoeuvres...).
Cornering lighting
With cornering lighting Without cornering lighting
Activation
The system operates:
- w hen the corresponding direction indicator
is switched on,
or
-

f
rom a certain angle of rotation of the
steering wheel.
Programming
The system is activated or
deactivated in the vehicle
configuration menu.
The system is activated by default.
Deactivation
The system does not operate:
- b elow a certain angle of rotation of the
steering wheel,
-

a
bove 25 mph (40 km/h),
-
w

hen reverse gear is engaged.
Lighting and visibility

88
Rear
If a significant accumulation of snow or
ice is present, or when using a bicycle
carrier on the boot, deactivate the
automatic rear wiper via the vehicle
configuration menu.Park.
Intermittent wipe.
Wash-wipe (set duration).
Reverse gear
When reverse gear is engaged, the rear wiper
will come into operation if the windscreen
wipers are operating. On
Press "MENU" to display the " MAIN
MENU ".
Select "Driving" .
Select "Secondary page" .
Select "Vehicle settings" .
Select the "Driving assistance" tab.
Activate the "Auto rear wiper in
reverse" function.
Configuration
This function is activated by default.
Off
Deactivate the "Auto rear wiper in reverse"
function.
The automatic rain sensitive windscreen
wipers must be reactivated by pushing
the control stalk downwards, if the
ignition has been off for more than
1


minute.
Do not cover the rain sensor, linked with
the sunshine sensor, located at the top
of the windscreen behind the rear view
m i r r o r.
Switch off the automatic rain sensitive
wipers when using an automatic car wash.
In winter, it is advisable to wait until the
windscreen is completely clear of ice
before activating the automatic rain
sensitive wipers.
Single wipe
Pull the stalk briefly towards you.
Unusual operation
If the wipers operate in intermittent mode when
in AUTO mode, have the system checked by a
PEUGEOT dealer or a qualified workshop.
Lighting and visibility

Driving139
208_en_Chap06_conduite_ed01-2016
Speed settings
F Go to the main menu by pressing the " MENU " button.
F

Sel
ect the " Driving" menu.
F

Sel
ect the secondary page.
F

Sel
ect "Speed settings ".
F

Sel

ect the speed to be modified.
F

P

ress on " Modify". As a safety measure, the driver must
only carry out these operations when
stationary.
F

E
nter the new value.
F Pr ess on confirm.
F C onfirm to save the modifications and quit
the menu.
Use this button to select all speeds.
Use this button to deselect all
speeds.
This button restores the factory
settings.
The speed values applied by the speed limiter
"
LIMIT " and the cruise control " CRUISE" can
be saved (up to 5 different speed settings).
With the touch screen
Advice
6

Driving
142
208_en_Chap06_conduite_ed01-2016
The collision can be automatically
avoided if the speed difference between
your vehicle and the one ahead is not
more than 9 mph (15 km/h).
Above this threshold, the system will do
what is possible to avoid or reduce the
seriousness of the accident by lowering
the speed of impact.
The automatic braking triggered:
-

c

an be even more effective if the driver
presses the brake pedal more firmly,
-

m

ay stop the vehicle, holding the brakes on
for 1.5 seconds when stationary to allow
the driver time to take back control of the
vehicle,
-

m

ay cause the engine to stall,
-

m

ay give rise to a pumping noise, due to
the pressurisation of the braking system.
Touch screen
Press " MENU" to display the " MAIN
MENU ".
Select " Driving ".
Select " Secondary page ".
Select " Vehicle settings ".
Select the " Driving assistance " tab.
Check the " Automatic emergency
braking activated " box.
Activation
Confirm. Deactivation
Check the "
Automatic emergency braking
deactivated " box.
The last selection remains in memory when the
ignition is switched off.
If the automatic emergency braking function is
deactivated, following each start a temporary
message will be displayed to signal this, once a
speed threshold (6 mph - 10 km/h) is exceeded.
To deactivate :
- F ollowing an impact to the windscreen
close to the sensor.
-

W
hen towing a trailer.
-
W

hen the vehicle is being towed.
-

W
hen the vehicle is about to cross a toll
payment barrier.
-

W
hen the vehicle is going through an
automatic car wash.

Driving153
208_en_Chap06_conduite_ed01-2016
Reinitialisation
It is necessary to reinitialise the system every
time one or more tyre pressures are adjusted,
and after changing one or more wheels.Before reinitialising the system, ensure
that the pressures of the four tyres are
correct for the use of the vehicle and in
line with the recommendations on the
tyre pressure label.
The under-inflation alert can only
be relied on if the reinitialisation of
the system has been done with the
pressures in the four tyres correctly
adjusted.
The under-inflation detection system
does not give a warning if a pressure is
incorrect at the time of reinitialisation. F

W
ith the ignition on and the
vehicle stationary, press this
button for about 3 seconds then
release it, an audible signal
confirms the reinitialisation.
The new pressure settings registered
are considered to be reference values
by the system.
Reinitialisation of the system is done with the
ignition on and the vehicle stationary.
F

P
ress "Under-inflation
initialisation ".
From the "
Driving assistance " menu
of the touch screen:
F

C
onfirm the instruction by pressing "Ye s",
an audible signal and a message confirm
the reinitialisation.
Operating fault
The flashing and then fixed illumination of the
under-inflation warning lamp accompanied
by illumination of the Service warning lamp
indicates a fault with the system.
In this case, under-inflation monitoring of the
tyres is no longer assured.
Have the system checked by a PEUGEOT
dealer or a qualified workshop.
Touch screen Screen A
Before doing anything to the system,
the pressures of the four tyres must be
checked and the system reinitialised.
6

Practical information175
208_en_Chap07_informations-pratiques_ed01-2016
Advice
While the quantity of AdBlue® in the additive
t
ank is sufficient, no information is displayed.
On the other hand, once the additive level
drops to the quantity needed for a range of
1 500 miles (2 400 km) driving, you are warned
by different temporary signals (warning lamp,
message, audible signal).
When the AdBlue
® tank is empty, restarting
becomes impossible. Different levels of alert are triggered according
to the remaining driving range threshold.
You will be informed as each mileage threshold
is reached and the alerts will change from
temporary to permanent.
-
T he 1st alert is triggered at a remaining
driving range of 1 500 miles (2 400 km).
-

T

he 2
nd alert is triggered at a remaining
driving range of 375 miles (600 km).
Up to 0 miles, at which point it will be
impossible to restart the engine after a stop.
Range indicators
It is strongly recommended that you do
not wait for the successive alerts before
topping-up the AdBlue
® tank, but do this
as soon as possible.
Driving range
Press this button to display the information.
With the touch screen:
If the range is greater than 3 100 miles
(5 000 km), a range value is not given. -

s
elect the "Driving assistance"
menu,
-
s

elect "Diagnostic",
-

s
elect CHECK.
7

225
208_en_Chap10b_SMEGplus_ed01-2016
7-inch touch screen
GPS satellite navigation - Multimedia audio - Bluetooth® telephone
Contents
First steps
2 26
Steering mounted controls

2
28
Menus
229
Navigation


230
Navigation - Guidance
2

38
Tr a f fi c
2

4 2
Radio Media

2
44
Radio


250
DAB (Digital Audio Broadcasting) radio

2
52
Media


254
Settings


258
Connected services
26

6
Internet browser
2

67
MirrorLink
TM 270
C
arPlay® 2 74
T
elephone
2
78
Frequently asked questions

2
86
The system is protected in such a way that it will only operate in
your vehicle. As a safety measure, the driver should only carry out operations
which require prolonged attention while the vehicle is stationary.
The display of an energy economy mode message signals that
electrical systems operating are going into standby.
Refer to the energy economy mode section.
10
Audio and Telematics

226
208_en_Chap10b_SMEGplus_ed01-2016
First steps
Use the buttons to the left of the touch screen
for access to the menu carousels, then press
the virtual buttons in the touch screen.
Each menu is displayed in one or two pages
(primary page and secondary page).Secondary page
Primary page In very hot conditions, the system may
go into stand-by (screen and sound
completely off) for a minimum period
of


5 minutes.
Audio and Telematics