2015 NISSAN QUEST air condition


> (GLW    0RGHO (' @
.Use the displayed lines and the bird's-eye
view as a reference. The lines and the bird's-
eye view are greatly affected by the number
of occupants, fuel level, vehicle position,
road condition and road grade.
SAA3571
Front-side viewGUID-04849896-C828-42DE-B9D2-225B3EFD328EGuiding lines:
Guiding lines that indicate the width and the
front end of the vehicle are displayed on the
monitor.
The front-of-vehicle line
*1shows the front part
of the vehicle.
The side-of-vehicle line
*2shows the vehicle
width including the outside mirrors.
The extensions
*3of both the front*1and
side
*2lines are shown with a green dotted
line.
CAUTION
. The turn signal light may look like
the side-of-vehicle line. This is not a
malfunction.
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-35
&RQGLWLRQ


> (GLW    0RGHO (' @
4-36Monitor, heater, air conditioner, audio, phone and voice recognition systems
JVH0168X
DIFFERENCE BETWEEN PREDICTIVE
AND ACTUAL DISTANCES
GUID-523096F1-0F36-43D7-BA0A-1C4191B4C267
Backing up on a steep uphillGUID-EAD39342-4AD0-4A64-BF28-9F7778BECE82When backing up the vehicle up a hill, the
distance guide lines and the vehicle width guide
lines are shown closer than the actual distance.
For example, the display shows 3 ft (1 m) to the
place
*A, but the actual 3 ft (1 m) distance on
the hill is the place
*B. Note that any object on
the hill is viewed in the monitor further than it
appears.
JVH1030X
Backing up on a steep downhillGUID-483DCB2B-8F6F-459F-A166-BB7BB62C9813When backing up the vehicle down a hill, the
distance guide lines and the vehicle width guide
lines are shown further than the actual distance.
For example, the display shows 3 ft (1 m) to the
place
*A, but the actual 3 ft (1 m) distance on
the hill is the place
*B. Note that any object on
&RQGLWLRQ


> (GLW    0RGHO (' @
the hill is viewed in the monitor closer than it
appears.
SAA2021
Backing up near a projecting objectGUID-3E24EFC9-F31F-4620-AB7B-DD9615F34056The predictive course lines*Ado not touch the
object in the display. However, the vehicle may
hit the object if it projects over the actual
backing up course.
JVH1026X
Backing up behind a projecting objectGUID-0257F1CE-FB10-4F0C-B9AF-05951940B700The position*Cis shown further than the
position
*Bin the display. However, the
position
*Cis actually at the same distance
as the position
*A. The vehicle may hit the
object when backing up to the position
*Aif
the object projects over the actual moving
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-37
&RQGLWLRQ


> (GLW    0RGHO (' @
4-38Monitor, heater, air conditioner, audio, phone and voice recognition systems
course.
HOW TO SWITCH THE DISPLAYGUID-666130BA-C2F3-463E-A7FE-5BBA4EC5786DWith the ignition switch in the ON position,
press the CAMERA button or move the shift
lever to the R (Reverse) position to operate the
Around View Monitor.
When the rear view is displayed on the left side
on the screen, the view on the right side
switches between the bird's-eye view and the
front-side view each time the CAMERA button is
pushed.
When the front view/bird's eye view is displayed
on the screen, pushing the CAMERA button will
switch the view on the right side to the front-side
view. When the CAMERA button is pushed
again, the screen which was displayed before
the Around View Monitor was activated is
displayed.
If the shift lever is in the R (Reverse) position, the
available views are:
.Rear view/bird's-eye view split screen
. Rear view/front-side view split screen
If the shift lever is in the P (Park) position, the
available views are:
. Front-view/bird's-eye view split screen
. Front-view/front-side view split screen
If the shift lever is in the D (Drive) position, the
only available view is front view/front-side view split screen.
The display will switch from the Around View
Monitor screen when:
.
When the shift lever is in the D (Drive)
position and the vehicle speed increases
above approximately 6 MPH (10 km/h) .
. When a different screen is selected.
HOW TO ADJUST THE SCREENGUID-D7D0605F-B226-4C3F-ACCC-199024F184E8To adjust the Display ON/OFF, Brightness, Tint,
Color, Contrast and Black Level of the Around
View Monitor, push the SETTING button with
the Around View Monitor on, select the item key
and adjust the level using the multi-function
controller.
Do not adjust the Brightness, Tint, Color,
Contrast and Black Level of the Around View
Monitor while the vehicle is moving. Make sure
the parking brake is firmly applied.
MOVING OBJECT DETECTION (MOD)
FUNCTION
GUID-07B1BAB2-9273-4950-8DE2-2CDABED123ECThe Moving Object Detection (MOD) system
can inform the driver of moving objects when
driving out of garages, maneuvering into parking
lots and in other such instances.
The MOD system detects moving objects by
using image processing technology on the
image shown in the display.
The MOD system operates in the following
conditions when the camera view is displayed:
.When the shift lever is in the ªPº or ªNº
position and the vehicle is stopped, the
MOD system detects the moving objects in
the bird's-eye view. The MOD system will
not operate if the outside mirror is moving in
or out or if either door is opened.
. When the shift lever is in the ªDº position
and the vehicle speed is below approxi-
mately 5 MPH (8 km/h) , the MOD system
detects moving objects in the front view.
. When the shift lever is in the ªRº position
and the vehicle speed is below approxi-
mately 5 MPH (8 km/h) , the MOD system
detects moving objects in the rear view. The
MOD system will not operate if the lift gate is
open.
The MOD system does not detect moving
objects in the front-side view. The MOD icon
&RQGLWLRQ


> (GLW    0RGHO (' @
is not displayed on the screen when in this view.
WARNING
.The MOD system is not a substitute
for proper vehicle operation and
does not prevent contact with the
objects surrounding the vehicle.
When maneuvering, always use the
outside mirror and inside rearview
mirror and turn and look to check
the surroundings to make sure it is
safe to maneuver.
. The system is not designed to pre-
vent contact with all objects.
. The MOD system is not designed to
detect surrounding stationary ob-
jects.
JVH0872X
bird's-eye view
JVH0873X
front view / rear view
When the MOD system detects a moving object
surrounding the vehicle, the yellow frame will be
displayed on the view where the objects are
detected and a chime will sound once. While the
MOD system continues to detect moving
objects, the yellow frame continues to be
displayed.
In the bird's-eye view, the yellow frame
*1is
displayed on each camera image (front, rear,
right, left) depending on where moving objects
are detected.
The yellow frame
*2is displayed on each view
in the front view and rear view modes.
A blue MOD icon is displayed in the view where
the MOD system is operative. A gray MOD icon
is displayed in the view where the MOD system
is not operative.
If the MOD system is turned off, the MOD icon
*3is not displayed.
The MOD system will turn on automatically
under the following conditions:
. When the shift lever is in the ªRº (Reverse)
position.
. When the CAMERA button is pushed to
switch from a different screen to the camera
view on the display.
. When vehicle speed decreases below
approximately 5 MPH (8 km/h) .
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-39
&RQGLWLRQ


> (GLW    0RGHO (' @
4-40Monitor, heater, air conditioner, audio, phone and voice recognition systems
.When the ignition switch is placed in the
OFF position and then back to the ON
position.
WARNING
.Do not use the MOD system when
towing a trailer. The system may not
function properly.
. Excessive noise (for example, audio
system volume or open vehicle
window) will interfere with the
chime sound, and it may not be
heard.
. The MOD system performance will
be limited according to environmen-
tal conditions and surrounding ob-
jects such as:
Ð When there is low contrast be-
tween background and the mov-
ing objects
Ð When there is blinking source of light.
Ð When strong light such as an- other vehicle's headlight or sun-
light is present. Ð When there is dirt, water drops
or snow on the camera lens.
Ð When the position of the moving objects in the display is not
changed.
. The MOD system might detect flow-
ing water droplets on the camera
lens, white smoke from the muffler,
moving shadows, etc.
. The MOD system may not function
properly depending on the speed,
direction, distance or shape of the
moving objects.
. If your vehicle sustains damage to
the parts where the camera is
installed, leaving it misaligned or
bent, the sensing zone may be
altered and the MOD system may
not detect objects properly.
. When the temperature is extremely
high or low, the screen may not
display objects clearly. This is not a
malfunction.
Camera maintenanceGUID-D1409542-36A1-4821-8E31-4CED639435BBIf dirt, rain or snow accumulates on the camera,
the MOD system may not operate properly.
Clean the camera.
SETTING MOVING OBJECT DETEC-
TION (MOD) ON/OFF
GUID-65416446-6E6C-49C2-9CD2-11B396017077To set Moving Object Detection (MOD) on/off,
push the SETTING button, select the ªDriver
Assistanceº key.
Moving Object Detection (MOD):
When this item is set to ON, the MOD is
activated. When this item is turned to OFF
(indicator turns off) , the MOD system is
deactivated.
MOD MALFUNCTIONGUID-6FE0810E-C774-474A-845D-D5D5936481DBWhen the orange MOD icon is displayed in the
view, the system is not functioning properly. This
will not hinder normal driving operation but the
system should be inspected by a NISSAN
dealer.
OPERATING TIPSGUID-E53B80D8-F195-4E4C-96AB-FF30E6EF3CE3
CAUTION
.Do not use alcohol, benzine or
thinner to clean the camera. This
will cause discoloration. To clean
&RQGLWLRQ


> (GLW    0RGHO (' @
the camera, wipe with a cloth dam-
pened with a diluted mild cleaning
agent and then wipe with a dry
cloth.
. Do not damage the camera as the
monitor screen may be adversely
affected.
. The screen displayed on the Around View
Monitor will automatically return to the
previous screen when no operation takes
place for 3 minutes after the CAMERA
button has been pushed while the shift lever
is in a position other than the ªRº (Reverse)
position.
. The display of images on the screen may be
delayed after screens are switched.
. When the temperature is extremely high or
low, the screen may not display objects
clearly. This is not a malfunction.
. When strong light directly shines on the
camera, objects may not be displayed
clearly. This is not a malfunction.
. The screen may flicker under fluorescent
light. This is not a malfunction.
. The colors of objects on the Around View
Monitor may differ somewhat from those of
the actual object. .
Objects on the monitor may not be clear and
the color of the object may differ in a dark
location or at night. This is not a malfunction.
. There may be differences in clearness
between each camera view of the bird's-
eye view.
. If dirt, rain or snow attaches to the camera,
the Around View Monitor may not display
objects clearly. Clean the camera.
. Do not use wax on the camera window.
Wipe off any wax with a clean cloth that has
been dampened with a mild detergent
diluted with water.
GUID-ADBCDC3B-14A7-4BB0-AB93-C7F6F05F9243
SAA3511
Center
CENTER VENTILATORSGUID-DE68D695-F57B-4B4B-B293-5172E4A17860Adjust the air flow direction of the ventilators by
moving the center knob (up/down, left/right)
until the desired position is achieved.
Monitor, heater, air conditioner, audio, phone and voice recognition systems4-41
VENTILATORS
&RQGLWLRQ


> (GLW    0RGHO (' @
4-42Monitor, heater, air conditioner, audio, phone and voice recognition systems
SAA3676
Side
SIDE VENTILATORSGUID-F08870EF-0946-4EEE-A94E-D1F2E688A0CCOpen/close the ventilators by moving the control
dial
*1to either direction.
: This symbol indicates that the ventilators areclosed. Moving the side control to this
direction will close the ventilators.
: This symbol indicates that the ventilators areopen. Moving the side control to this
direction will open the ventilators.
Adjust the air flow direction of the ventilators by
moving the center knob
*2(up/down, left/right)
until the desired position is achieved.
SAA3055
Rear
REAR VENTILATORSGUID-DAFEFF24-3A4B-4F4E-A7FD-EE54F99AA552If the center knob is moved fully to the left or
right, the ventilators will be closed.
Adjust the air flow direction of the ventilators by
moving the center knob (up/down, left/right)
until the desired position is achieved.
GUID-80BBDF64-A7D7-4098-B53C-6003FA8720E9
WARNING
. The heater and air conditioner oper-
ate only when the engine is running.
. Never leave children or adults who
would normally require the support
of others alone in the vehicle. Pets
should not be left alone either. They
could unknowingly activate
switches or controls and inadver-
tently become involved in a serious
accident and injure themselves. On
hot, sunny days, temperatures in a
closed vehicle could quickly become
high enough to cause severe or
possibly fatal injuries to people or
animals.
. Do not use the recirculation mode
for long periods as it may cause the
interior air to become stale and the
windows to fog up.
. Do not adjust the heating and air
conditioning controls while driving
so that full attention may be given
to vehicle operation.
The heater and air conditioner operate when the
engine is running. The air blower will operate
HEATER AND AIR CONDITIONER
&RQGLWLRQ