2015 NISSAN JUKE emergency towing


> (GLW   0RGHO )'@
passenger car.The vehicle isnot
designed forcornering atthe same
speeds asconventional passenger
cars. Failure tooperate thisvehicle
correctly couldresult inloss of
control and/orarollover accident.
. Always usetires ofthe same type,
size, brand, construction (bias,bias-
belted orradial) ,and tread pattern
on allfour wheels. Installtraction
devices onthe front wheels when
driving onslippery roadsanddrive
carefully.
. Besure tocheck thebrakes imme-
diately afterdriving inmud orwater.
See ªBrake systemº (P.5-35) forwet
brakes.
. Avoid parking yourvehicle onsteep
hills. Ifyou getout ofthe vehicle
and itrolls forward, backward or
sideways, youcould beinjured.
. Whenever youdrive off-road
through sand,mudorwater asdeep
as the wheel hub,more frequent
maintenance mayberequired. See
the maintenance informationinthe
ªNISSAN ServiceandMaintenance
Guideº . .
Spinning thefront wheels onslip-
pery surfaces maycause theAWD
warning lighttoflash andtheAWD
system toautomatically switchfrom
the AWD mode tothe 2WD mode.
This could reduce traction. Beespe-
cially careful whentowing atrailer
(AWD model) .
GUID-A A9BA26A-B 49B-43B0-A908-85126 20A8F65
WARNING
Do not operate thepush-button ignition
switch whiledriving thevehicle except
in an emergency. (Theengine willstop
when theignition switchispushed 3
consecutive timesorthe ignition switch
is pushed andheld formore than2
seconds.) Ifthe engine stopswhilethe
vehicle isbeing driven, thiscould lead
to acrash andserious injury.
Before operating thepush-button ignition
switch, besure tomove theshift lever tothe P
(Park) position (forContinuously Variable Trans-
mission models) orthe shift lever tothe N
(Neutral) position(formanual transmission
models) .
Starting anddriving
5-9
PUSH-BUT TON IGNITION SWITCH
&RQGLWLRQ


> (GLW   0RGHO )'@
SCE0933
Installing thespare tire
GUID-5EA97 2A8-ECC0-4 BA2-9DA3-AA3F89474 077
The spare tireisdesigned foremergency
use. (See specific instructions underthe
heading ªWheels andtiresº (P.8-31) .)
1. Clean anymud ordirt from thesurface
between thewheel andhub.
2. Carefully putthespare tireonand tighten
the wheel nutsfinger tight.Check thatallthe
wheel nutscontact thewheel surface
horizontally .
3. With thewheel nutwrench, tightenwheel
nuts alternately andevenly inthe sequence
as illustrated (
*
1
,
*
2
,
*
3
,
*
4
,
*
5
) , more
than 2times, untilthey aretight. 4.
Lower thevehicle slowlyuntilthetire
touches theground. Then,withthewheel
nut wrench, tightenthewheel nutssecurely
in the sequence asillustrated. Lowerthe
vehicle completely .
WARNING
. Incorrect wheelnutsorimproperly
tightened wheelnutscancause the
wheel tobecome looseorcome off.
This could cause anaccident.
. Do not use oilorgrease onthe
wheel studsornuts. Thiscould
cause thenuts tobecome loose.
. Retighten thewheel nutswhen the
vehicle hasbeen driven for600
miles (1,000 km)(also incases ofa
flat tire, etc.).
.
As soon aspossible, tightenthe
wheel nutstothe specified torque
with atorque wrench.
Wheel nuttightening torque:
80 ft-lb (108 N´m)
The wheel nutsmust bekept tightened
to specifications atall times. Itis
recommended thatthewheel nutsbe tightened
tospecifications ateach
lubrication interval.
.
Adjust tirepressure tothe COLD
pressure.
COLD pressure:
After thevehicle hasbeen parked for3
hours ormore ordriven lessthan 1mile
(1.6 km).
COLD tirepressures areshown onthe
Tire andLoading Information label
affixed tothe driver sidecenter pillar.
Stowing thedamaged tireand thetools
GUID-91AF 6071-9A97-4265-A3F7 -ED7B079600F0
1. Securely storethejack, tools andthe
damaged tireinthe storage area.
2. Replace thecargo floorboxand board.
3. Close theliftgate.
WARNING
. Always makesurethatthespare tire
and jacking equipment areproperly
secured afteruse.Such items can
become dangerous projectilesinan
accident orsudden stop.
. The spare tireand small sizespare
tire aredesigned foremergency use.
See specific instructions underthe
In case ofemergency
6-7
&RQGLWLRQ


> (GLW   0RGHO )'@
6-10
In case ofemergency
CAUTION
Do not keep thestarter motorengaged
for more than10seconds. Ifthe engine
does notstart right away, placethe
ignition switchinthe OFF position and
wait 10seconds beforetryingagain.
9. After starting yourengine, carefully discon-
nect thenegative cableandthen thepositive
cable (
*
4
?
*
3
?
*
2
?
*
1
) .
10. Replace thevent caps (ifso equipped) .Be
sure todispose ofthe cloth usedtocover
the vent holes asitmay becontaminated
with corrosive acid.
GUID-A764 C60A-F34B- 45BD-8A21-8 3DCBF259F31
Do not attempt tostart theengine bypushing.
CAUTION
. Continuously Variable Transmission
(CVT) models cannotbepush-
started ortow-started. Attempting
to do somay cause transmission
damage.
. Three-way catalystequipped mod-
els should notbestarted bypushing
since thethree waycatalyst maybe
damaged.
. Never trytostart thevehicle by
towing it; when theengine starts,
the forward surgecouldcause the
vehicle tocollide withthetow
vehicle.
GUID-70 6E277F-8F7 5-437A-8E9B -3AA46086CF31
CAUTION
. Do not continue todrive ifyour
vehicle overheats. Doingsocould
cause engine damage oravehicle
fire.
. To avoid thedanger ofbeing
scalded, neverremove theradiator
cap while theengine isstill hot.
When theradiator capisremoved,
pressurized hotwater willspurt out,
possibly causingseriousinjury.
. Do not open thehood ifsteam is
coming out.
If your vehicle isoverheating (indicatedbyan
extremely hightemperature gaugereading) ,or if
you feel alack ofengine power, detectabnormal
noise, etc.,takethefollowing steps:
1. Move thevehicle safelyoffthe road and
apply theparking brake.
2. Continuously Variable Transmission
(CVT) models:
Move theshift lever tothe P(Park) position.
Manual Transmission (MT)models:
Move theshift lever tothe N(Neutral)
position.
PUSH STARTING IFYOUR VEHICLE OVERHEA TS
&RQGLWLRQ


> (GLW   0RGHO )'@
6-12
In case ofemergency
GUID-9C30 82E6-7E05-4 D3B-99BC-7AC9A9D1 154A
When towing yourvehicle, allState (Provincial in
Canada) andlocal regulations fortowing must
be followed. Incorrecttowingequipment could
damage yourvehicle. Towing instructions are
available fromaNISSAN dealer.Localservice
operators arefamiliar withtheapplicable laws
and procedures fortowing. To assure proper
towing andtoprevent accidental damageto
your vehicle, NISSAN recommends thatyou
have aservice operator towyour vehicle. Itis
advisable tohave theservice operator carefully
read thefollowing precautions.
WARNING
. Never rideinavehicle thatisbeing
towed.
. Never getunder yourvehicle afterit
has been lifted byatow truck.
CAUTION
. When towing, makesurethatthe
transmission, axles,steering system
and powertrain areinworking con-
dition. Ifany unit isdamaged, dol-
lies must beused. .
Always attachsafetychains before
towing.
For information abouttowing yourvehicle behind
a recreational vehicle(RV),see ªFlat towingº
(P .9-17) ofthis manual.
T OWING YOUR VEHICLE
&RQGLWLRQ


> (GLW   0RGHO )'@
SCE0950
T wo-wheel drivemodels
T OWING RECOMMENDE DBY
NISSAN
GUID-09B96 2BF-4170-4F2F-83C9 -E1E70F0C2C59
T wo-Wheel Drive(2WD) models
GUID-528 26B00-51 B3-4A50-B8 98-5192FE87 088D
NISSAN recommends thatyour vehicle be
towed withthedriving (front)wheels offthe
ground orplace thevehicle onaflat bed truck as
illustrated.
CAUTION
. Never towCVT models withthefront
wheels onthe ground orfour
wheels onthe ground (forward or
backward) ,as this may cause ser- ious
andexpensive damagetothe
transmission. Ifitis necessary to
tow thevehicle withtherear wheels
raised, always usetowing dollies
under thefront wheels.
. When towing CVTmodels withthe
front wheels ontowing dollies:
Push theignition switchtothe
ACC orON position, andsecure
the steering wheelinastraight-
ahead position witharope orsimi-
lar device. Movetheshift lever to
the N(Neutral) position. .
When towing aCVT model withthe
rear wheels onthe ground (ifyou do
not use towing dollies):Always
release theparking brake.
In case ofemergency
6-13
&RQGLWLRQ


> (GLW   0RGHO )'@
6-14
In case ofemergency
SCE0952
All-wheel drivemodels
All-Wheel Drive(AWD) models
GUID-F1452 A8C-FBB7-4 968-A917-24030A5251A 3
NISSAN recommends thattowing dolliesbe
used when towing yourvehicle orthe vehicle be
placed onaflat bed truck asillustrated.
CAUTION
Never towAWD models withanyofthe
wheels onthe ground asthis may cause
serious andexpensive damagetothe
powertrain.
VEHICLE RECOVER Y(freeing astuck
vehicle)
GUID-8B A26C80-AB 41-4D31-91 EB-1E623D595DAA
WARNING
. Stand clearofastuck vehicle.
. Donot spin your tires athigh speed.
This could cause themtoexplode
and result inserious injury.Partsof
your vehicle couldalsooverheat
and bedamaged.
Pulling astuck vehicle
GUID-732 B880F-D49E-4C39-8F6 2-BB53A9900276
Do not use thetiedown hookfortowing or
vehicle recovery .
&RQGLWLRQ


> (GLW   0RGHO )'@
6-16
In case ofemergency
. Never towavehicle usingthevehi-
cle tiedown hookorrecovery hook.
. Always pullthecable straight out
from thefront ofthe vehicle. Never
pull onthe vehicle atan angle.
. Pulling devices shouldberouted so
they donot touch anypart ofthe
suspension, steering,brakeorcool-
ing systems.
. Pulling devices suchasropes or
canvas strapsarenot recommended
for use invehicle towingorrecov-
ery.
Rocking astuck vehicle
GUID-2A46 1430-45B5-4FEA-9A27- 9404CC0BC37B
If your vehicle isstuck insand, snow,mud, etc.,
use thefollowing procedure:
1. Turn offthe Vehicle Dynamic Control(VDC)
system.
2. Make surethearea infront andbehind the
vehicle isclear ofobstructions.
3. Turn thesteering wheelrightandlefttoclear
an area around thefront tires.
4. Slowly rockthevehicle forward andback-
ward.
.
Shift back andforth between R(Reverse)
and D(Drive) (Continuously Variable T
ransmission models)or1st and R
(Reverse) (ManualTransmission models).
.
Apply theaccelerator aslittle aspossible
to maintain therocking motion.
.
Release theaccelerator pedalbefore
shifting between Rand D(Continuously
V ariable Transmission models)or1st and
R (Manual Transmission models).
.
Do not spin thetires above 35MPH (55
km/h) .
5. Ifthe vehicle cannotbefreed afterafew
tries, contact aprofessional towingservice
to remove thevehicle.
&RQGLWLRQ


> (GLW   0RGHO )'@
GUID-F20F 5531-4E6B -4F82-BAD2 -1E941D903DB6
Do not tow atrailer withyour vehicle.
GUID-FC6 6003B-B76C-4 2AB-9FCA-588DF863F 95A
T owing yourvehicle withallfour wheels onthe
ground issometimes calledflattowing. This
method issometimes usedwhen towing a
vehicle behindarecreational vehicle,suchasa
motor home.
CAUTION
. Failure tofollow theseguidelines
can result insevere transmission
damage.
. Whenever flattowing yourvehicle,
always towforward, neverback-
ward.
. DO NOTtow anyContinuously Vari-
able Transmission (CVT)vehicle
with allfour wheels onthe ground
(flat towing) .Doing soWILL DA-
MAGE internal transmission parts
due tolack oftransmission lubrica-
tion.
. DO NOTtow anAll-Wheel Drive
(AWD) vehicle withanyofthe
wheels onthe ground. Doingso
may cause serious andexpensive
damage tothe powertrain.
. For emergency towingprocedures
refer toªTowing yourvehicleº (P.6- 12)
.
CONTINUOUS LY VARIABLE TRANS-
MISSION (CVT)
GUID-A9F1 7C32-174D -4848-8C9E-5 43DA151F46E
All-Wheel Drive(AWD) models:
Do not tow anAWD vehicle withanyofthe
wheels onthe ground.
T wo-Wheel Drive(2WD) models:
T o tow avehicle equipped withaContinuously
V ariable Transmission (CVT),an appropriate
vehicle dollyMUST beplaced underthetowed
vehicle's drivingwheels. Always followthedolly
manufacturer's recommendations whenusing
their product.
MANUAL TRANSMISSIO N
GUID-B1176 14A-9FD0-4D51-A6E3-47024288B 9E1
. Always towwith themanual transmission in
Neutral.
. Your vehicle speedshould neverexceed 70
MPH (112km/h) whenflattowing your
vehicle.
. After towing 500miles (805km),start and
idle theengine withthetransmission in
Neutral fortwo minutes. Failuretoidle the
engine afterevery 500miles (805km)of
towing maycause damage tothe transmis-
sion's internal parts.
T echnical andconsumer information
9-17
T OWING ATRAILER FLATTOWING
&RQGLWLRQ