2015 NISSAN GT-R brake

5-24Starting and driving
when the vehicle is driven, a wheel may
not roll correctly, or the brake pads
could be damaged. If the pads are
damaged, this may reduce the effec-
tiveness of the brake system which
could cause a collision, serious perso-
nal injury or death.
The GT-R uses brake pad mater�fals that have
h�fgh metall�f�b �bontent. The brake pad mater�fal
helps ma�fnta�fn brak�fng performan�be �fn a w�fde
range of weather and dr�fv�fng �bond�ft�fons.
For the f�frst 3,000 m�fles (5,000 km) of the
veh�f�ble’s serv�f�be l�ffe, and for the f�frst 3,000 m�fles
(5,000km) after a brake repla�bement, the brake
pad to brake rotor �blearan�be �fs very small. When
park�fng, apply the park�fng brake and move the
sh�fft lever to the
&Ppos�ft�fon. Idle the eng�fne for
more than 20 se�bonds w�fthout depress�fng the
brake pedal. Th�fs allows the brake pads to move
away from the rotor so the pad does not �bonta�bt
the rotor.
Add�ft�fonally, the brakes must be dry before
park�fng the veh�f�ble after dr�fv�fng on wet roads or
after wash�fng the veh�f�ble. If the roads are wet,
l�fghtly apply the brakes for a short d�fstan�be
before park�fng the veh�f�ble to dry the brakes.
After wash�fng the veh�f�ble, dry the brakes by
dr�fv�fng on a dry road for a few m�fles and apply the brakes normally based on traff�f�b and road
�bond�ft�fons.
The metall�f�b brake pads and brake d�fs�b rotor
may rust together when the brakes are not
appl�fed:
.
If the veh�f�ble �fs not �fdled for 20 se�bonds
w�fthout the brakes appl�fed, or �ff the brakes
are appl�fed when the veh�f�ble �fs shut off, the
rotor and pads �ban rust together, even when
the brake pads are dry.
. If the brakes are wet when the veh�f�ble �fs
parked and the park�fng brake �fs appl�fed for a
long t�fme.
Conta�bt a GT-R �bert�ff�fed NISSAN dealer �ff the
brake pads and brake rotor have rusted
together.
1. Br�fng the veh�f�ble to a �bomplete stop.
2. W�fth the foot brake pedal depressed, apply the park�fng brake.
3. Move the sh�fft lever to the
&Ppos�ft�fon.
4. Che�bk the sh�fft lever pos�ft�fon �fnd�f�bator on the �fnstrument panel to �bonf�frm that the
&P
pos�ft�fon �fs sele�bted.
5. Push the �fgn�ft�fon sw�ft�bh to stop the eng�fne.
WARNING
Before exiting the vehicle, be sure to
move the shift lever to the&Pposition
and stop the engine. If the engine is
running and the shift lever is not in the
&Pposition, the vehicle may start mov-
ing due to partial engagement of the
clutch or to the effects of gravity on a
slope, or the vehicle may suddenly
accelerate due to accidental operation
of the accelerator pedal, possibly caus-
ing an accident.

abled, the warning light illuminates.
When the warning light illuminates,
perform cool down driving.
(
“Cool down” page GTR-13)
When the warning light turns off,
the function can be used again.
. The performance of start may vary
depending on the amount of wheel
spin ,or increase and decrease of
the engine output in response to the
outside temperature. (This vehicle
was set up according to the road
surface conditions of the straight
sections of the Sendai Highland
Raceway course in Japan at 598F
(158C) .)
. For safety reasons, VDC control may
activate automatically when driving
on a slippery road surface, such as a
wet road, in order to apply the
brakes or limit the engine output.
. Frequent use of the R mode start
function increases the load on the
powertrain related parts such as the
clutch and transmission compared
to normal driving. In particular, the
clutch will wear out more quickly.
HOW TO USE R MODE START
FUNCTION
1. Move the shift lever to the&Aor&Mposition.
2. Select the R �fode with the trans�fission set�bp switch. (
“VDC, trans�fission and
s�bspension set�bp switches” page 5-25)
3. Select the R �fode with the VDC set�bp switch.
4. Depress the brake pedal fir�fly with yo�br left foot and keep depressing the brake pedal.
5. Depress the accelerator pedal q�bickly to the floor with yo�br right foot while the brake
pedal is depressed. The engine speed will
increase to approxi�fately 4,000 rp�f and
will be �faintained.
6. Within 3 seconds after depressing the accelerator pedal, release the brake pedal.
WARNING
. Be sure the parking brake is fully
released before driving. Failure to
do so can cause brake failure and
lead to an accident.
. Do not release the parking brake
from outside the vehicle.
. Do not use the shift lever in place of
the parking brake. When parking, be
sure the parking brake is fully
engaged.
. Do not leave children unattended in
Starting and driving5-33
PARKING BRAKE

5-34Starting and driving
a vehicle. They could release the
parking brake and cause an acci-
dent.
To apply: Pull the parking brake lever up\f
To release:
1\f Firml\b appl\b the foot brake\f
2\f While pulling up on the parking brake lever slightl\b, push the button
*Aand lower the
lever completel\b\f
3\f Before driving, be sure the brake warning light goes out\f The cruise control allows driving at speeds
above 25 MPH (40 km/h) without keeping \bour
foot on the accelerator pedal\f
WARNING
Do not use the cruise control when
driving under the following conditions.
Doing so could cause a loss of vehicle
control and result in an accident.
.
When it is not possible to keep the
vehicle at a set speed.
. In heavy traffic or in traffic that
varies in speed.
. On winding or hilly roads.
. On slippery roads (rain, snow, ice,
etc.) .
. In very windy areas.
NOTE:
. When the SAVE mode is selected with
the transmission setup switch, the
acceleration and deceleration can be
controlled smoothly. When the SAVE
mode is selected, the maximum setting
speed is lower than the one in the
normal mode. When the vehicle ap- proaches a gentle uphill, there may be
a slight delay as the vehicle returns to
the preset speed. However, the vehicle
will gradually accelerate and return to
the preset speed.
CRUISE CONTROL

Passing another vehicle
To pass another vehicle, depress the accelerator
pedal. When yo�f release the pedal, the vehicle
will ret�frn to the previo�fsly set speed.
Increasing the set vehicle speed
To reset at a faster cr�fising speed, �fse one of
the following �bethods:
.Depress the accelerator pedal. When the
vehicle attains the desired speed, p�fsh and
release the SET/COAST switch.
. P�fsh and hold the RESUME/ACCELERATE
switch. When the vehicle attains the speed
yo�f desire, release the switch.
. P�fsh and then q�fickly release the RESUME/
ACCELERATE switch. Each ti�be yo�f do
this, the set speed will increase by abo�ft 1
MPH or 1 k�b/h.
Decreasing the set vehicle speed
To reset at a slower cr�fising speed, �fse one of
the following �bethods:
.Lightly tap the brake pedal. When the
vehicle attains the desired speed, p�fsh
and release the SET/COAST switch.
. P�fsh and hold the SET/COAST switch.
Release the switch when the vehicle slows down to the desired speed.
. P�fsh and then q�fickly release the SET/
COAST switch. Each ti�be yo�f do this, the
set speed will decrease by abo�ft 1 MPH or
1 k�b/h.
Resuming the preset speed
To res�f�be the preset speed, p�fsh and release
the RESUME/ACCELERATE switch. The vehicle
will res�f�be the last set cr�fising speed when the
vehicle speed is over 25 MPH (40 k�b/h) .
Canceling the preset speed
To cancel the preset speed, �fse one of the
following �bethods:
.P�fsh the CANCEL switch
*1. The SET
indicator will t�frn off.
. Tap the brake pedal
*3. The SET indicator
will t�frn off.
. T�frn the MAIN switch
*2off. Both the
CRUISE indicator and SET indicator will t�frn
off.
Starting and driving5-37

5-38Starting and driving
NOTE:
.If cruise control was canceled by press-
ing the cancel switch or by depressing
the brake pedal, the system changes to
standby status.
. If you depress the brake pedal while
pushing the RESUME/ACCELERATE or
SET/COAST switch and reset at the
cruising speed, the cruise control will
be deactivated. Turn the MAIN switch
off once and then turn it on again.
Under the following conditions�f cruise control
will be auto�batically canceled.
. Vehicle speed drops to below approxi�bately
19 MPH (30 k�b/h) .
. Vehicle speed drops to �bore than approxi-
�bately 8 MPH (13 k�b/h) below the set
vehicle speed.
. The shift lever is �boved to a position other
than
&A
F&M.
. VDC operates.
. A tire is spinning.
. There is a �balfunction in the cruise control
syste�b.
WARNING
.Never rely solely on the hill start
assist system to prevent the vehicle
from moving backward on a hill.
Always drive carefully and atten-
tively. Depress the brake pedal
when the vehicle is stopped on a
steep hill. Be especially careful
when stopped on a hill on frozen
or muddy roads. Failure to prevent
the vehicle from rolling backwards
may result in a loss of control of the
vehicle and possible serious injury
or death.
. The hill start assist system is not
designed to hold the vehicle at a
standstill on a hill. Depress the
brake pedal when the vehicle is
stopped on a steep hill. Failure to
do so may cause the vehicle to roll
backwards and may result in a
collision or serious personal injury.
. The hill start assist may not prevent
the vehicle from rolling backwards
on a hill under all load or road
conditions. Always be prepared to
depress the brake pedal to prevent the vehicle from rolling backwards.
Failure to do so may result in a
collision or serious personal injury.
NOTICE
When the vehicle is stopped on a hill,
do not hold the vehicle in place by
depressing the accelerator pedal. Doing
so may cause the clutch to overheat and
result in transmission damage. Use the
brakes to prevent the vehicle from
moving.
The hill start assist syste�b auto�batically keeps
the brakes applied to help prevent the vehicle
fro�b rolling backwards in the ti�be it takes the
driver to release the brake pedal and apply the
accelerator when the vehicle is stopped on a hill.
Hill start assist will operate auto�batically under
the following conditions:
. The shift lever is �boved to a forward or
reverse position.
. The vehicle is stopped co�bpletely on a hill
by applying the brake.
The �baxi�bu�b holding ti�be is 2 seconds. After 2
seconds the vehicle will begin to roll back and
HILL START ASSIST

5-40Starting and driving
certified NISSAN dealer in accordance �fith
specifications for cit�b driving to high perfor-
mance driving.
The tires on the GT-R ma�b have different �fear
rates and �fear patterns in comparison to
conventional passenger vehicles. Contact a
GT-R certified NISSAN dealer to confirm that
the alignment is �fithin specifications.Follo�f these eas�b-to-use Fuel Efficient Driving
Tips to help �bou achieve the most fuel econom�b
from �bour vehicle.
1. Use smooth accelerator and brake pedal
application.
.Avoid rapid starts and stops..Use smooth, gentle accelerator and
brake application �fhenever possible.
.Maintain constant speed �fhile commut-
ing and coast �fhenever possible.
2. Maintain constant speed.
.Look ahead to tr�b and anticipate and
minimize stops.
.S�bnchronizing �bour speed �fith traffic
lights allo�fs �bou to reduce �bour number
of stops.
.Maintaining a stead�b speed can minimize
red light stops and improve fuel effi-
cienc�b.
3. Use air conditioning (A/C) at higher vehicle speeds.
.Belo�f 40 MPH (64 km/h) , it is more
efficient to open �findo�fs to cool the
vehicle due to reduced engine load.
.Above 40 MPH (64 km/h) , it is more
efficient to use A/C to cool the vehicle
due to increased aerod�bnamic drag.
.Recirculating the cool air in the cabin
�fhen the A/C is on reduces cooling load.
4. Drive at economical speeds and distances.
.Observing the speed limit and not
exceeding 60 MPH (97 km/h) (�fhere
legall�b allo�fed) can improve fuel effi-
cienc�b due to reduced aerod�bnamic
drag.
.Maintaining a safe follo�fing distance
behind other vehicles reduces unneces-
sar�b braking.
.Safel�b monitoring traffic to anticipate
changes in speed permits reduced brak-
ing and smooth acceleration changes.
.Select a gear range suitable to road
conditions.
5. Use cruise control.
.Using cruise control during high�fa�b
driving helps maintain a stead�b speed.
.Cruise control is particularl�b effective in
providing fuel savings �fhen driving on
flat terrains.
6. Plan for the shortest route.
.Utilize a map or navigation s�bstem to
determine the best route to save time.
FUEL EFFICIENT DRIVING TIPS

5-46Starting and driving
WARNING
.Do not stop or park the vehicle over
flammable materials such as dry
grass, waste paper or rags. They
may ignite and cause a fire.
. Never leave the engine running
while the vehicle is unattended.
. Do not leave children unattended
inside the vehicle. They could un-
knowingly activate switches or con-
trols. Unattended children could
become involved in serious acci- dents.
. Safe parking procedures require
that both the parking brake be
applied and the transmission placed
into the
&Pposition. Failure to do so
could cause the vehicle to move
unexpectedly or roll away and result
in an accident.
. Make sure the shift lever has been
pushed as far forward as it can go
and cannot be moved without de-
pressing the foot brake pedal. .
Follow the instructions below when
parking the vehicle to help prevent
the brake rotor and brake pads from
rusting together. Failure to follow
the instructions could cause the
rotor and pads to rust together. If
the rotor and pads rust together,
there may be a popping noise and
some vibration when the vehicle is
driven, a wheel may not roll cor-
rectly, or the brake pads could be
damaged. If the pads are damaged,
this may reduce the effectiveness of
the brake system which could cause
a collision, serious personal injury
or death.
1. Firmly apply the parkin�f brake.
2. M�bve the shift lever t�b the&Pp�bsiti�bn.
3. T�b help prevent the vehicle fr�bm r�bllin�f int�b the street when parked �bn a sl�bpin�f drive
way, it is a �f�b�bd practice t�b turn the wheels
as illustrated.
.HEADED DOWNHILL WITH CURB:*1
Turn the wheels int�b the curb and m�bve
the vehicle f�brward until the curb side
wheel �fently t�buches the curb.
PARKING/PARKING ON HILLS

5-48Starting and driving
BRAKING PRECAUTIONS
The brake system has two separate hydra�flic
circ�fits�b If one circ�fit malf�fnctions, yo�f will still
have braking at two wheels�b
Yo�f may feel a small click and hear a so�fnd
when the brake pedal is f�flly depressed slowly�b
This is not a malf�fnction and indicates that the
brake assist mechanism is operating properly�b
Vacuum assisted brakes
The brake booster aids braking by �fsing engine
vac�f�fm�b If the engine stops, yo�f can stop the
vehicle by depressing the brake pedal�b However,
greater foot press�fre on the brake pedal will be
req�fired to stop the vehicle and the stopping
distance will be longer�b
Wet brakes
When the vehicle is washed or driven thro�fgh
water, the brakes may get wet�b As a res�flt, yo�fr
braking distance will be longer and the vehicle
may p�fll to one side d�fring braking�b
To dry brakes, drive the vehicle at a safe speed
while lightly tapping the brake pedal to heat-�fp
the brakes�b Do this �fntil the brakes ret�frn to
normal�b Avoid driving the vehicle at high speeds
�fntil the brakes f�fnction correctly�b
Using the brakes
Avoid resting yo�fr foot on the brake pedal while
driving�b This will ca�fse overheating of the
brakes, wearing o�ft the brake and pads faster
and red�fce gas mileage�b
To help red�fce brake wear and to prevent the
brakes from overheating, red�fce speed and
downshift to a lower gear before going down a
slope or long grade�b Overheated brakes may
red�fce braking performance and co�fld res�flt in
loss of vehicle control�b
WARNING
.While driving on a slippery surface,
be careful when braking, accelerat-
ing or downshifting. Abrupt braking
or accelerating could cause the
wheels to skid and result in an
accident.
. If the engine is not running or is
turned off while driving, the power
assist for the brakes will not work.
Braking will be harder.
PARKING BRAKE BREAK-IN
Break in the parking brake shoes whenever the
stopping effect of the parking brake is weakened
or whenever the parking brake shoes and/or
dr�fms/rotors are replaced, in order to ass�fre the
best braking performance�b
This proced�fre is described in the vehicle
service man�fal and can be performed by a
GT-R certified NISSAN dealer�b
BRAKE SYSTEM