2015 MITSUBISHI L200 Cooling system

CAUTIONlNormally, use the “” (outside) position
to keep the windscreen and side windows clear and quickly remove fog or frost from
the windscreen.
If high cooling performance is desired, or if
the outside air is dusty or otherwise contami-
nated, use the “
” (recirculation) position.
Set the air selection lever to the “
” (out-
side) position periodically to increase venti-
lation so that the windows do not become fogged up.
l Use of the “
” (recirculation) position for
extended time may cause the windows to fog up.
Air conditioning switch*
E00701500781
Push the switch, and the air conditioning
compressor will turn on. The air conditioning
indication lamp (A) will come on.
Push the switch again and the air condition-
ing compressor will stop and the indication
lamp goes off.
CAUTIONl When using the air conditioning, the idling
speed may slightly increase as the air condi- tioning compressor is switched on/off auto-
matically. While the vehicle with an A/T is
stationary, fully depress the brake pedal to
prevent the vehicle from creeping.Operating the air conditioning
system
E00701800247
Heating
Set the mode selection dial to the “” posi-
tion and set the air selection lever to the
“
” (outside) position.
Turn the temperature control dial clockwise
or anticlockwise to the desired temperature. Select the desired blower speed.NOTEl For maximum heat, set the blower speed at
the 3 rd
position.
Heater/Manual air conditioning*
7-06OKTE15E3For pleasant driving7 LHD RHD LHD RHD

CAUTIONlWhen using the air conditioning, the idling
speed may slightly increase as the air condi-
tioning compressor is switched on/off auto- matically. While the vehicle with an A/T is
stationary, fully depress the brake pedal to prevent the vehicle from creeping.Operating the system in auto-
matic mode
E00704100919
In normal conditions, use the system in the
AUTO mode and follow these procedures: 1. Set the blower speed selection dial to the
“AUTO” position.
2. Select the temperature control dial to the
desired temperature. The temperature
can be set within a range of 17 to 27 (Type 1) or 20 to 30 (Type 2). The tem-
perature will gradually increase as the dial is turned to the right.
3. Set the mode selection dial to the “AU-
TO” position.
4. Push the air conditioning switch to oper-
ate the air conditioning. When the air
conditioning operates, the indication lamp (A) in the dial will come on.
The outlet port (except “
”) and blower
speed, and ON/OFF of air conditioning will
be controlled automatically.
NOTEl Set the temperature at about 22 (Type 1) or
25 (Type 2) under normal conditions.NOTEl When the temperature is set to the highest or
the lowest setting under the AUTO opera-
tion, the air selection, mode selection, blow- er speed and the air conditioning will be au-
tomatically changed as follows.
Also, if manually operated after an automat-
ic changeover, manual operation will be se- lected.
• Quick Heating (When the temperature is
set to the highest setting)
Outside air will be introduced, the air
flow will select foot position, and the air conditioning will stop.
• Quick Cooling (When the temperature is
set to the lowest setting)
Inside air will be recirculated, the air flow
will select face position, and the air condi-
tioning will operate.Operating the system in man-
ual mode
E00704200040
Blower speed and ventilator mode may be
controlled manually by setting the blower speed selection dial and the mode selection
dial to the desired positions. To return to au-
tomatic operation, set the dials to the “AU- TO” position.
Automatic air conditioning*
7-12OKTE15E3For pleasant driving7

Important operation tips forthe air conditioning E00708300951
l Park the vehicle in the shade.
Parking in the hot sun will make the ve-
hicle inside extremely hot, and it will re-
quire more time to cool the interior.
If it is necessary to park in the sun, open the windows for the first few minutes of
air conditioning operation to expel the
hot air.
l Close the windows when the air condi-
tioning is in use. The entry of outside air
through open windows will reduce the cooling efficiency.
l Too much cooling is not good for the
health. The inside air temperature should
only be 5 to 6 °C below the outside air temperature.
l When operating the system, make sure
the air intake, which is located in front
of the windscreen, is free of obstructions such as leaves and snow. Leaves collec- ted in the air-intake plenum may reduce
air flow and plug the plenum water
drains.Air conditioning system refrig-
erant and lubricant recommen-dations
If the air conditioning seems less effective than usual, the cause might be a refrigerant
leak. We recommend you to have the system inspected.
The air conditioning system in your vehicle must be charged with the refrigerant
HFC-134a and the lubricant ZXL-100PG.
Use of any other refrigerant or lubricant will
cause severe damage which will result in the need to replace your vehicle’s entire air con-
ditioning system. The release of refrigerant into the atmosphere should be prevented.
It is recommended that the refrigerant be re- covered and recycled for further use.
During a long period of disuse
The air conditioning should be operated for at
least five minutes each week, even in cold
weather. This is to prevent poor lubrication of the compressor internal parts and to main-
tain the air conditioning in the best operating
condition.
Air purifier*
E00708400675
An air filter has been incorporated into this air conditioning so that dirt and dust are
cleaned from the air.
Replace the air filter periodically as its ability
to clean the air will be reduced as it collects pollen and dirt. For the maintenance interval,
refer to the “SERVICE BOOKLET”.NOTEl Operation in certain conditions such as driv-
ing on a dusty road and frequent use of the air conditioning can lead to reduction of
service life of the filter. When you feel that the air flow is lower than normal or when the windscreen or windows start to fog up
easily, replace the air filter.
We recommend you to have it checked.
Important operation tips for the air conditioning
7-14OKTE15E3For pleasant driving7

3.Confirm that the cooling fan is turning.
If the fan is not turning, stop the engine
immediately and have it checked.
A- Radiator cap B- Cooling fan
C- Reserve tank
*: if so equipped
WARNINGl Be careful not to get your hands or clothes
caught in the cooling fan.4. After the engine coolant temperature has
dropped to the normal temperature, stop the engine.
5. Check the coolant level in the reserve
tank.
WARNINGl If there is none, make sure that the engine
has cooled down before removing the ra-
diator cap, because hot steam or boiling water otherwise will gush from the fillerport and may scald you.
6. Add coolant to the radiator and/or re-
serve tank if necessary (refer to the
“Maintenance” section.)
CAUTIONl Do not add coolant while the engine is hot.
Suddenly adding cold coolant could damage
the engine. Wait for the engine to cool
down, then add coolant a little at a time.
7. Examine the radiator hoses for coolant
leakage and the drive belt for looseness
or damage.
If there is anything wrong with the cool-
ing system or drive belt, we recommend
you to have it checked and repaired.
Bleeding the fuel system
E00800700312
The fuel system should be bled to remove air
as described below if the fuel supply is ex- hausted during travel.
Bleeding the fuel system
8-05OKTE15E3For emergencies8

NOTElUse of additives is not recommended since
they may reduce the effectiveness of addi-
tives already included in the engine oil. It may result in failure of the mechanical as-
sembly.
Vehicles with diesel particulate
filter (DPF)
l Select engine oil of the proper SAE vis-
cosity number according to the atmos- pheric temperature.
l Use engine oil conforming to the follow-
ing classification: • ACEA classification: “For service C1, C2, C3 or C4”
• JASO classification: “For service DL-1”
If those classifications are not available, contact a MITSUBISHI MOTORS Au-
thorized Service Point.
NOTEl Use of additives is not recommended since
they may reduce the effectiveness of addi-
tives already included in the engine oil. It may result in failure of the mechanical as-
sembly.Engine coolant
E01000502153
To check the coolant level
A transparent coolant reserve tank (A) is lo-cated in the engine compartment.
The coolant level in this tank should be kept
between the “LOW” and “FULL” marks when measured while the engine is cold.
*: Front of the vehicle
To add coolant
The cooling system is a closed system and
normally the loss of coolant should be very
slight. A noticeable drop in the coolant level
could indicate leakage. If this occurs, we rec- ommend you to have the system checked as
soon as possible.
If the level should drop below the “LOW” level on the reserve tank, open the lid and
add coolant.
Also, if the reserve tank is completely empty, remove the radiator cap (B) and add coolant until the level reaches the filler neck.
WARNINGl Do not open the radiator cap (B) while the
engine is hot. The coolant system is under
pressure and any hot coolant escaping
could cause severe burns.
Anti-freeze
The engine coolant contains an ethylene gly-
col anti-corrosion agent. The cylinder head and water pump housing are cast aluminium
alloy, and periodic changing of the engine coolant is necessary to prevent corrosion of
these parts.

Use “ MITSUBISHI MOTORS GENUINE
SUPER LONG LIFE COOLANT” or equiva- lent.
Engine coolant
10-06OKTE15E3Maintenance10 Type 1
Type 2

MITSUBISHI MOTORS GENUINE Coolant
has excellent protection against corrosion and rust formation of all metals including alumi-
nium and can avoid blockages in the radiator, heater, cylinder head, engine block, etc.
Because of the necessity of this anti-corro-
sion agent, the coolant must not be replaced with plain water even in summer. The re-
quired concentration of anti-freeze differs de-
pending on the expected ambient tempera- ture.Ambient
tempera-
ture (mini- mum) °C
-15-20-25-30-35-50
Anti-freezeconcentra- tion %
303540455060CAUTIONl Do not use alcohol or methanol anti-freeze
or any engine coolants mixed with alcohol
or methanol anti-freeze. The use of an im- proper anti-freeze can cause corrosion of the
aluminium components.
l For effective anti-corrosion and anti-freeze
performance, keep the anti-freeze concentra-tion within the range of 30 to 60 %.
Concentrations exceeding 60 % will result in
a reduction of both the anti-freeze and cool-
ing performance thus adversely affecting the
engine.CAUTIONl Do not top up with water only.
Water by itself reduces the rust-protective and anti-freeze qualities of the coolant and
has a lower boiling point. It can also cause damage to the cooling system if it should freeze. Do not use tapwater, as it can causecorrosion and rust formation.
During cold weather
If the temperatures in your area drop below
freezing, there is the danger that the coolant
in the engine or radiator could freeze and cause severe damage to the engine and/or ra-diator.
Add a sufficient amount of anti-freeze to the
coolant to prevent it from freezing.
The concentration should be checked before the start of cold weather and anti-freeze add- ed to the system if necessary.
Automatic transmission
fluid* E01000602125
The proper amount of automatic transmission fluid is essential to the life and operation of
the automatic transmission. Either insuffi- cient fluid or excessive fluid could causetransmission trouble. The transmission fluid filler port cap is equipped with a dipstick.Use the following procedure to check the flu-
id level.
Procedure for checking the flu- id level
1. Check the fluid level after the vehicle
has been driven enough to warm up the
transmission fluid.
2. Park the vehicle on a flat, level surface
and apply the parking brake.
3. With the engine idling and the brake
pedal fully depressed, move the trans- mission selector lever through all the po-sitions from P” (PARK) to “D”
(DRIVE), stopping momentarily at each position.
4. Move the selector lever to the “P”
(PARK) position.
5. Remove the dipstick and wipe it with a
clean lint-free cloth.
6. Reinsert the dipstick as far as it goes.
Automatic transmission fluid*
10-07OKTE15E3Maintenance10