Hydroplaning
..................................... 155 I
Immobilizer .......................................... 61
Indicator lamp
see Warning and indicator lamps
Indicators
see Turn signals
Insect protection on the radiator ......27
Installing a wheel
Installing the adapter (spare
wheel ) ............................................ 309
Instrument cluster
Fuel gage ...................................... .181
Important safety notes .................. 180
Instrument cluster lighting ............. 181
Outside temperature displa y.......... 181
Overview .......................................... 34
Speedometer ................................. 181
Tachometer ................................... 181
Warning and indicator lamps ........... 35
Instrument cluster lighting .............. 181
Instrument lighting
see Instrument cluster lighting
Interior lighting ................................... 97
Front ................................................ 97
Motion detectors ............................. 99
Notes on replacing bulbs ............... 105
Replacing bulb s............................. 105
Switching the rear compartment
lighting on centrally ......................... 98
Interior motion sensor
Arming ............................................. 62
Deactivating ..................................... 62
Function ........................................... 62
Switching off .................................... 62 J
Jack Jacking points ................................ 307
Preparation .................................... 307
Storage location ............................ 274
Using ............................................. 307
Jump-starting ..................................... 276 K
Key Position in the ignition lock ............ 138
Key positions ..................................... 138
Kickdown ........................................... 144 L
Lamps see Warning and indicator lamps
Lane Keeping Assist
Activating/deactivating ................. 166
Function/note s............................. 165
Language
Display (vehicles with steering
wheel buttons) ............................... 190
Lashing points and tie downs
Permissible tensile load ................. 327
LATCH-type (ISOFIX) child seat
anchors ................................................ 53
License plate lamp
Replacing bulb s............................. 103
License plate lamp (Chassis Cab)
Replacing bulb s............................. 104
Light sensor ......................................... 93
Lighting
see Lights
Lighting
see Lights
Lights
Activating/deactivating daytime
running lamps (on-board com-
puter with steering wheel but-
tons) .............................................. 192
Activating/deactivating surround
lighting (vehicles with steering
wheel buttons) ............................... 193
Automatic headlamp mode .............. 93
Bulb failure indicator ........................ 92
Cornering light function ................... 95
Driving abroad ............................... 153
Fog lamps ........................................ 93
Hazard warning lamps ..................... 95
High beam flasher ............................ 94
High-beam headlamp s..................... 94
Highbeam Assist .............................. 96
Important safety notes .................... 92 12
Index
X
Assemble the lug wrench extension using
the middle rod and the rod with the largest diameter from the three-piece jack pump
lever.
X Starting with the middle rod, slide the lug
wrench extension as far as it will go onto
the lug wrench.
X Using lug wrench 0043, loosen the wheel
bolts/wheel nuts on the wheel to be
changed by about one full turn. Do not
unscrew the wheel bolts/nuts completely.
Raising the vehicle G
WARNING
If you do not position the jack correctly at the appropriate jacking point of the vehicle, the
jack could tip over with the vehicle raised.
There is a risk of injury.
Only position the jack at the appropriate jack-
ing point of the vehicle. The base of the jack
must be positioned vertically, directly under
the jacking point of the vehicle. G
WARNING
On uphill and downhill slopes, the jack could
tip over with the vehicle raised. There is a risk of injury.
Do not change wheels on uphill or downhill
gradients. Notify a qualified specialist work-
shop.
! Only position the jack on the jacking
points intended for this purpose. You could
otherwise damage the vehicle. Observe the following when raising the vehi-
cle:
R When raising the vehicle, only use the jack
which Mercedes-Benz has specifically
approved for your vehicle.
R The vehicle's jack is intended only to raise
the vehicle for a short time when changing
a wheel. It is not suited for performing
maintenance work under the vehicle.
R Avoid changing the wheel on uphill and
downhill slopes.
R Before raising the vehicle, secure it from
rolling away by applying the parking brake
and inserting wheel chocks. Never disen-
gage the parking brake while the vehicle is
raised.
R The jack must be placed on a firm, flat and
non-slip surface. On a loose surface, a
large, load-bearing underlay must be used. On a slippery surface, a non-slip underlay
must be used, e.g. rubber mats.
R Make sure that the distance between the
underside of the tires and the ground does
not exceed 1.2 in(3 cm).
R Never place your hands or feet under the
raised vehicle.
R Never lie under the raised vehicle.
R Never start the engine when the vehicle is
raised.
R Never open or close a door when the vehi-
cle is raised.
R Make sure that no persons are present in
the vehicle when the vehicle is raised.
! Only use the jack pump lever middle rod
and the rod with the largest diameter as a
lug wrench extension. Only slide the middle rod as far as it will go onto the lug wrench. The rods may otherwise bend and be dis-
torted to such an extent that they can no
longer be used as a pump lever for the jack.
! Do not place the jack on the leaf spring or
the differential case. Changing wheels
307Wheels and tires Z
Hydraulic jack
Preparing the hydraulic jack
X Insert the third rod of jack pump lever 0043
into the lug wrench extension.
Jack pump lever 0043is assembled.
X Close pressure release screw 0044.
X To do this, use the flattened section on
pump lever 0043to turn pressure release
screw 0044clockwise to the stop.
i Do not turn pressure release screw
0044
more than 1 or 2 full turns. Hydraulic fluid
could otherwise escape.
X Insert pump lever 0043into the recess on the
jack and secure by turning it clockwise.
X Place the jack vertically beneath the jack-
ing points described below. Jacking point, front axle
Jacking point at the front axle
X Place the jack under the longitudinal mem-
ber in front of the front axle. Jacking point, rear axle (example: vehicle type
2500) Jacking point, rear axle (example: vehicle type
3500)
Jacking point at the rear axle on vehicle
types 2500 and 3500
X Place the jack under the longitudinal mem-
ber in front of the rear axle. Jacking point, rear axle (example: Cab Chassis)
Jacking point at the rear axle on chassis
versions
X Place the jack next to the front leaf spring
support beneath the jacking point. 308
Changing wheelsWheels and tires