Page 15 of 27
14
When Driving
For details, refer to Section 4, “Mazda Radar Cruise Control (MRCC)”.
Mazda Radar Cruise Control (MRCC) Display IndicationSetting the Mazda Radar Cruise Control (MRCC)
The Mazda Radar Cruise Control (MRCC) system may be cancelled during rain,
fog, snow or other inclement weather conditions, or when the front surface of the
radiator grille is dirty.
NOTE
Under the following conditions, operation of the Mazda Radar Cruise Control
(MRCC) system is temporarily cancelled. The Mazda Radar Cruise Control
(MRCC) indicator light (green) turns off simultaneously.
• The CANCEL switch is pressed or the brake pedal is depressed.
The setting status of the Mazda Radar Cruise Control (MRCC) system is indicated
in the display in the instrument cluster.
A system malfunction or operation conditions are indicated by a warning.
• The parking brake is applied.
• The shift lever is in the P, N, or R position (for manual transaxle vehicles,
R position only).
• The vehicle speed decreases to less than 25 km (16mph).
• The DSC, Smart Brake Support (SBS) system, or the Smart City Brake
Support (SCBS) system is operating.
• A system malfunction is detected.
Other details are described in the related text.
Vehicle ahead display
MRCC Distance between vehicle displayMRCC Set
vehicle speed
$ 9 @ & ; & & % @ & E J U J P O @ 2 V J D L ( V J E F J O E C
Page 23 of 27
22
When Driving
Diesel Particulate Filter
The diesel particulate filter collects and eliminates most of the particulate matter
(PM) in the exhaust gas of the diesel engine for improved exhaust gas processing
ability.
While the particulate matter (PM) collected in the diesel particulate filter is
eliminated automatically, fuel may be mixed with the engine oil increasing the
engine oil level. If the engine oil level exceeds the “X” mark on the dipstick,
replace the engine oil.
For details, refer to Section 4, “Tyre Pressure Monitoring System” or
“Diesel Particulate Filter”.
The Tyre Pressure Monitoring System (TPMS) monitors the air pressure of all
four tyres. If the air pressure of one or more tyres is too low, the system warns the
driver by indicating the tyre pressure monitoring system warning light in the
instrument cluster and operating a beep sound.
In the following cases, system initialization must be performed so that the system
operates normally.
• A tyre pressure is adjusted.
• Tyre rotation is performed.
• A tyre or wheel is replaced.
• The tyre pressure monitoring system warning
light is illuminated.
Tyre Pressure Monitoring System
$ 9 @ & ; & & % @ & E J U J P O @ 2 V J D L ( V J E F J O E C
Page 24 of 27
Interior Features
23
Temperature control dial Fan control dial Mode selector dial
A/C switch Air intake selector switch Rear window defogger switch
Air-Conditioning System (Fully Automatic Type)
Operation of Automatic Air Conditioning
1. Set the mode selector dial to the AUTO position.
2. Set the air intake selector to the outside air position (indicator light turned off).
3. Set the fan control dial to the AUTO position.
4. Press the A/C switch to operate the air conditioning (turn indicator light on).
5. Set the temperature control dial to the desired position.
6. To turn off the system, set the fan control dial to the 0 position.
For details, refer to Section 5, “Air-Conditioning System”.
$ 9 @ & ; & & % @ & E J U J P O @ 2 V J D L ( V J E F J O E C
Page 26 of 27
Maintenance and Care
25
Inspection and Engine Oil Refill
Selector
If the engine oil level exceeds the “X” mark on the dipstick, replace the engine oil.
When inspecting the engine oil level, pull out the dipstick straight without twisting.
In addition, when inserting the dipstick, always insert it without twisting so that the
“X” mark faces the front of the vehicle.
For details, refer to Section 6, “Owner Maintenance”.
NOTE
The initialization (engine oil data resetting) of the recorded value can be
performed using the following procedure:
1. Switch the ignition OFF.
2. Switch the ignition ON with the selector pressed, and press and hold the
selector for about 5 seconds until the master warning light flashes.
3. After the master warning light flashes for several seconds, the
initialization is completed.
X Mark Full Low
Whenever the engine oil is replaced, the vehicles engine control unit needs to be
reset as soon as possible. Otherwise the wrench indicator light or engine oil warning
light may turn on. To reset the engine control unit, consult an expert repairer, we
recommend an Authorised Mazda Repairer or refer to the vehicle engine control
unit reset procedure.
$ 9 @ & ; & & % @ & E J U J P O @ 2 V J D L ( V J E F J O E C
Page 27 of 27
If Trouble Arises
26
If Trouble Arises
• Flat Tyre
If you have a flat tyre, drive slowly to a level spot that is well off the road and
out of the way of traffic to change the tyre.
In the event of a flat tyre, use the emergency flat tyre repair kit to repair the tyre
temporarily or use the temporary spare tyre.
• Overheating
1. Drive safely to the side of the road and park off the right-of-way.
2. Check whether coolant or steam is escaping from the engine compartment.
If steam is coming from the engine compartment:
Do not go near the front of the vehicle. Stop the engine.
Wait until the steam dissipates, then open the bonnet and start the engine.
If neither coolant nor steam is escaping:
Open the bonnet and idle the engine until it cools.
• Towing Description
We recommend that towing be done only by an expert repairer, we recommend
an Authorised Mazda Repairer or a commercial tow-truck service.
• Warning Lights and Warning Sounds
If a warning light illuminates or flashes or a warning sound is heard, check for
details concerning the warning light or sound in this guide. If the problem
cannot be resolved, contact an Authorised Mazda Repairer.
For details, refer to Section 7, “Flat Tyre”, “Overheating”, “Emergency Towing” or
“Warning/Indicator Lights and Warning Sounds”.
$ 9 @ & ; & & % @ & E J U J P O @ 2 V J D L ( V J E F J O E C
