2015 MAZDA MODEL CX-3 ESP

*Some models.4–111
When Driving
i-ACTIVSENSE
Blind Spot Monitoring (BSM) System *
The Blind Spot Monitoring (BSM) system is designed to assist the driver in checking the
area to the rear of the vehicle on both sides during lane changes by alerting the driver to the
presence of vehicles approaching from the rear in an adjacent lane.
The Blind Spot Monitoring (BSM) system detects vehicles approaching from the rear while
travelling in the forward direction at a speed of 30 km/h (19 mph) or faster and turns on
the Blind Spot Monitoring (BSM) warning lights equipped on the door mirrors depending
on the conditions. If the direction indicator lever is operated to signal a lane change in
the direction in which the Blind Spot Monitoring (BSM) warning light is illuminated,
the system warns the driver of a vehicle in the detection area by fl ashing the Blind Spot
Monitoring (BSM) warning light and activating a beep sound.
The detection area on this system covers the driving lanes on both sides of the vehicle and
from the rear part of the front doors to about 50 m (164 ft) behind the vehicle.
Detection areas Your vehicle
WARNING
Always check the surrounding area visually before making an actual lane change:
The system is only designed to assist you in checking for vehicles at your rear when
making a lane change. Due to certain limitations with the operation of this system, the
Blind Spot Monitoring (BSM) warning light may not fl ash or it might be delayed even
though a vehicle is in an adjacent driving lane. Always make it your responsibility as a
driver to check the rear.
$9@&;&&%@&EJUJPOJOEC







4–122
When Driving
i-ACTIVSENSE
WARNING
Always check the surrounding area visually before actually putting the vehicle in
reverse:
The system is only designed to assist you in checking for vehicles at the rear when
putting the vehicle in reverse. Due to certain limitations with the operation of this
system, the Blind Spot Monitoring (BSM) warning light may not fl ash or it might be
delayed even though a vehicle is behind your vehicle. Always make it your responsibility
as a driver to check the rear.
NOTE
  In the following cases, the Blind Spot Monitoring (BSM) OFF indicator light turns
on and operation of the system is stopped. If the Blind Spot Monitoring (BSM) OFF
indicator light remains illuminated, have the vehicle inspected at an Authorised Mazda
Dealer as soon as possible.
 


 Some problem with the system including the Blind Spot Monitoring (BSM) warning
lights has occurred.
 


 A large deviation in the installation position of a radar sensor (rear) on the vehicle
has occurred.
 


 There is a large accumulation of snow or ice on the rear bumper near a radar sensor
(rear).
 


 Driving on snow-covered roads for long periods.



 The temperature near the radar sensors becomes extremely hot due to driving for
long periods on slopes during the summer.
 


 The battery voltage has decreased.
$9@&;&&%@&EJUJPOJOEC







4–14 0
When Driving
i-ACTIVSENSE
WARNING
Do not rely on the Smart City Brake Support System (SCBS) as a substitute for safer
driving:
The Smart City Brake Support (SCBS) system cannot compensate for unsafe and
reckless driving, excessive speed, tailgating (following another vehicle too closely), and
driving on slippery roads such as wet, snowy, and icy roads (reduced tyre friction and
road contact because of water on the road surface). You can still have an accident.
Do not rely completely on the Smart City Brake Support (SCBS) system:
 
 The Smart City Brake Support (SCBS) system is only designed to reduce damage in
the event of a collision. Over reliance on the system leading to the accelerator pedal
or brake pedal being mistakenly operated could result in an accident.
  The Smart City Brake Support (SCBS) is a system which operates in response to a
vehicle ahead. The system may not be able to detect or react to two-wheeled vehicles
or pedestrians.
  The laser sensor (front) for the Smart City Brake Support (SCBS) system is installed
near the rearview mirror. To assure the correct operation of the Smart City Brake
Support (SCBS), heed the following cautions.
 

 
 Do not apply stickers to the surface of the windscreen near the laser sensor (front)
(including transparent stickers). Otherwise, the laser sensor (front) may not be
able to detect vehicles ahead which could result in an accident.
 

 
 Do not apply coating agent to the windscreen. Otherwise, the laser sensor (front)
may not be able to detect vehicles or obstructions in front which could result in an
accident.
 

 
 Do not disassemble the laser sensor (front) .


 
 If cracks or damage caused by fl ying gravel or debris is visible near the laser
sensor (front) , stop using the Smart City Brake Support (SCBS) system
immediately and have your vehicle inspected by an expert repairer, we recommend
an Authorised Mazda Repairer. If the vehicle continues to be driven with cracks or
scratch marks left on the windscreen near the laser sensor (front) , the system may
operate unnecessarily and cause an unexpected accident.
  Refer to Stopping The Smart City Brake Support (SCBS) System Operation on
page 4-143 .
 

 
 When replacing the windscreen wipers or windscreen, consult an expert repairer,
we recommend an Authorised Mazda Repairer.
Do not modify the suspension:
If the vehicle height or inclination is changed, the system will not be able to correctly
detect vehicles ahead. This will result in the Smart City Brake Support (SCBS) system
not operating normally or mistakenly operating, which could cause a serious accident.
$9@&;&&%@&EJUJPOJOEC







4–16 4
When Driving
Tyre Pressure Monitoring System
CAUTION
  Each tyre, including the spare (if provided), should be checked monthly when cold
and infl ated to the infl ation pressure recommended by the vehicle manufacturer on the
vehicle placard or tyre infl ation pressure label. (If your vehicle has tyres of a different
size than the size indicated on the vehicle placard or tyre infl ation pressure label, you
should determine the proper tyre infl ation pressure for those tyres.)
 As an added safety feature, your vehicle has been equipped with a tyre pressure
monitoring system (TPMS) that illuminates a low tyre pressure telltale when one or
more of your tyres is signifi cantly under-infl ated. Accordingly, when the low tyre
pressure telltale illuminates, you should stop and check your tyres as soon as possible,
and infl ate them to the proper pressure. Driving on a signifi cantly under-infl ated tyre
causes the tyre to overheat and can lead to tyre failure. Under-infl ation also reduces
fuel effi ciency and tyre tread life, and may affect the vehicle's handling and stopping
ability.
 Please note that the TPMS is not a substitute for proper tyre maintenance, and it is the
driver's responsibility to maintain correct tyre pressure, even if under-infl ation has not
reached the level to trigger illumination of the TPMS low tyre pressure telltale.
 Your vehicle has also been equipped with a TPMS malfunction indicator to indicate
when the system is not operating properly.
 The TPMS malfunction indicator is combined with the low tyre pressure telltale.
When the system detects a malfunction, the telltale will fl ash for approximately
one minute and then remain continuously illuminated. This sequence will continue
upon subsequent vehicle start-ups as long as the malfunction exists. When the
malfunction indicator is illuminated, the system may not be able to detect or signal
low tyre pressure as intended. TPMS malfunctions may occur for a variety of reasons,
including the installation of replacement or alternate tyres or wheels on the vehicle that
prevent the TPMS from functioning properly. Always check the TPMS malfunction
telltale after replacing one or more tyres or wheels on your vehicle to ensure that the
replacement or alternate tyres and wheels allow the TPMS to continue to function
properly.
  To avoid false readings, the system samples for a little while before indicating a
problem. As a result it will not instantaneously register a rapid tyre defl ation or blow
out.
$9@&;&&%@&EJUJPOJOEC







4–181
When Driving
Parking Sensor System
Rear Corner Sensor
Distance detection area Distance between vehicle and obstruction Beeper sound *1
Far distance Approx. 50—38 cm (19—14 in) Medium intermittent sound
Middle distance Approx. 38—25 cm (14.0—9.8 in)
Fast intermittent sound
Close distance Within approx. 25 cm (9.8 in)
Continuous sound
*1 The rate at which the intermittent sound beeps increases as the vehicle approaches the obstruction.
NOTE
If an obstruction is detected in a zone for 6 seconds or more, the beep sound is stopped
(except for the close-distance zone). If the same obstruction is detected in another zone,
the corresponding beep sound is heard.
$9@&;&&%@&EJUJPOJOEC







5–33
Interior Features
Audio System
Preset channel tuning
The 6 preset channels can be used to store
6 AM and 12 FM stations.
1. To set a channel fi rst select AM, FM1,
or FM2. Tune to the desired station.
2. Press a channel preset button for
about 2 seconds until a beep is heard.
The preset channel number or station
frequency will be displayed. The
station is now held in the memory.
3. Repeat this operation for the other
stations and bands you want to store.
To tune one in the memory, select AM,
FM1, or FM2 and then press its channel
preset button. The station frequency or
the channel number will be displayed.
Auto memory tuning
This is especially useful when driving in
an area where the local stations are not
known.
Press and hold the auto memory button
(
) for about 2 seconds until a beep
is heard; the system will automatically
scan and temporarily store up to 6 stations
with the strongest frequencies in each
selected band in that area.
After scanning is completed, the station
with the strongest frequency will be tuned
and its frequency displayed. Press and
release the auto memory button (
)
to recall stations from the auto-stored
stations. One stored station will be
selected each time and its frequency and
channel number will be displayed.
NOTE
If no stations can be tuned after scanning
operations, “ A ” will be displayed.
$9@&;&&%@&EJUJPOJOEC







5–112
Interior Features
Bluetooth®
Audio Operation Using Voice Recognition (Type C/Type D)
Main audio operation
The below commands are examples of the available commands.
When the talk button is pressed and the following command is spoken out, the audio can be
operated. The commands in the () can be omitted. The specifi ed name and number are put
into the {}.
Voice command Function Corresponding audio
source
(Go to/Play) AM (Radio) Switches the audio source to AM radio. All
(Go to/Play) FM (Radio) Switches the audio source to FM radio. All
(Go to/Play) DAB (Radio) Switches the audio source to DAB radio. All
(Go to/Play) Bluetooth (Audio) Switches the audio source to BT audio. All
(Go to/Play) Aha (Radio) Switches the audio source to Aha™ Radio. All
(Go to/Play) Stitcher Switches the audio source to Stitcher™ Radio. All
(Go to/Play) USB 1 Switches the audio source to USB 1. All
(Go to/Play) USB 2 Switches the audio source to USB 2. All
Play Playlist {Playlist name} Plays the selected playlist. USB
Play Artist {Artist name} Plays the selected artist. USB
Play Album {Album name} Plays the selected album. USB
Play Genre {Genre name} Plays the selected genre. USB
Play Folder {Folder name} Plays the selected folder. USB
NOTE
  Some commands cannot be used depending on devices and use conditions. 
 If the Bluetooth ® device, USB, or AUX is not connected, the related commands cannot
be used.
$9@&;&&%@&EJUJPOJOEC







5–125
Interior Features
Bluetooth®
4. Download will be started from the
mobile phone.
NOTE
  Attached data is not downloaded. 
 Messages up to 1 kilobyte
(e-mail)/140-bytes (SMS) can be
downloaded.
  A message list is created for each
device.
  If the connected device does not
correspond to MAP 1.0, the AT
command is used to download. The
downloaded message indicates that it
is already read.
  Downloading using the AT command
may not function depending on the
connected device.
Receiving messages
(Method 1)
When a device receives a message, a
message received notifi cation is displayed.
The “Email Notifi cations” (E-mail) or
“SMS Notifi cations” (SMS) setting must
be on.
Refer to Communication Settings on page
5-128 .
Select
and display the message.
(Method 2)
1. Select the
icon on the home screen
and display the Communication screen.
2. Select
and display the new
message list for e-mail and SMS.
3. Select the message you would like to
display.
$9@&;&&%@&EJUJPOJOEC