2015 MAZDA MODEL CX-3 low beam

4–103
When Driving
i-ACTIVSENSE
NOTE
The timing in which the system switches the headlights changes under the following
conditions. If the system does not switch the headlights appropriately, manually switch
between high and low beams according to the visibility as well as road and traffi c
conditions.
 
 When there are sources of light in the area such as street lamps, illuminated
signboards, and traffi c signals.

 When there are refl ective objects in the surrounding area such as refl ective plates and
signs.
  When visibility is reduced under rain, snow and foggy conditions. 
 When driving on roads with sharp curves or hilly terrain. 
 When the headlights/rear lamps of vehicles in front of you or in the opposite lane are
dim or not illuminated.
  When there is suffi cient darkness such as at dawn or dusk. 
 When the luggage compartment is loaded with heavy objects or the rear passenger
seats are occupied.
  When visibility is reduced due to a vehicle in front of you spraying water from its tyres
onto your windscreen.
$9@&;&&%@&EJUJPOJOEC







4–104
When Driving
i-ACTIVSENSE
To Operate the System
The High Beam Control System (HBC)
operates to switch the headlights
automatically between high and low
beams after the ignition is switched ON
and the headlight switch is in the AUTO
and high beam position. At the same time,
the High Beam Control System (HBC)
indicator light (green) in the instrument
cluster illuminates.
The High Beam Control System (HBC)
determines that it is dark based on the
brightness of the surrounding area.
NOTE
  When the vehicle speed is 30 km/h
(18 mph) or higher, the headlights
automatically switch to high beams
when there are no vehicles ahead
or approaching in the opposite
direction.
 When the vehicle speed is less
than about 20 km/h (12 mph), the
High Beam Control System (HBC)
switches the headlights to low
beams.
  The low beams may not switch to
high beams when cornering.
  Operation of the High Beam Control
System (HBC) function can be
disabled. Refer to Personalisation
Features on page 9-13 .
Manual Switching
Switching to low beams
Shift the lever to the low beam position.
The High Beam Control System (HBC)
indicator light (Green) turns off.
Switching to high beams
Turn the headlight switch to the
position.
The High Beam Control System (HBC)
indicator light (Green) turns off and the
is illuminated.
$9@&;&&%@&EJUJPOJOEC







4–142
When Driving
i-ACTIVSENSE
NOTE
  The Smart City Brake Support (SCBS) detects a vehicle ahead by emitting a near-
infrared laser beam and receiving the beam refl ected off the refl ector of the vehicle
ahead, and then using it for the measurement. Consequently, the Smart City Brake
Support (SCBS) may not operate under the following conditions:
 


 Refl ection of the laser is poor due to the shape of the vehicle ahead.



 The vehicle ahead is signifi cantly dirty.



 Under bad weather condition, such as rain, fog and snow.



 The window washer is being used or the windscreen wipers are not used when it's
raining.
 


 The windscreen is dirty.



 The steering wheel is turned completely left or right, or the vehicle is accelerated
rapidly and comes close to the vehicle ahead.
 


 Trucks with low loading platforms and vehicles with an extremely low or high
profi le.




 Vehicles with certain shapes such as a vehicle carrier. 

 Under the following conditions, the Smart City Brake Support (SCBS) system may not
operate normally.
 


 Heavy luggage is loaded in the luggage compartment or on the rear seat.



 If there is the possibility of partial contact with a vehicle ahead.



 When driving on continuously curving roads, and entering and exiting exits.



 Elongated luggage or cargo is loaded onto installed roof rails and covers the laser
sensor (front) .
 


 Exhaust gas from the vehicle in front, sand, snow, and water vapour rising from
manholes and grating, and water splashed into the air.
 


 When towing a malfunctioning vehicle.



 When driving with tyres having signifi cantly different wear. 

 In the following cases, the laser sensor (front) may inadvertently determine that there
is a vehicle ahead and the Smart City Brake Support (SCBS) system may operate.
 


 Objects on the road at the entrance to a curve.



 Vehicles passing in the opposite lane while making a curve.



 Metal objects, bumps, or protruding objects on the road.



 When passing through a toll gate equipped with a bar.



 When passing under a vinyl curtain or fl ag.



 Plastic objects such as pylons.



 Two-wheeled vehicles, pedestrians, animals or standing trees. 

(Manual transaxle) If the vehicle is stopped by the SCBS operation and the clutch pedal is not depressed,
the engine stops.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–14 8
When Driving
i-ACTIVSENSE
Forward Sensing Camera (FSC) *
Your vehicle is equipped with a Forward Sensing Camera (FSC). The Forward Sensing
Camera (FSC) is positioned near the rearview mirror and used by the following systems.
 


 High Beam Control System (HBC)



 Lane Departure Warning System (LDWS)



 Smart Brake Support (SBS)
Forward Sensing Camera (FSC)
The Forward Sensing Camera (FSC) determines the conditions ahead of the vehicle while
travelling at night and detects traffi c lanes. The distance in which the Forward Sensing
Camera (FSC) can detect objects varies depending on the surrounding conditions.
$9@&;&&%@&EJUJPOJOEC







4–149
When Driving
i-ACTIVSENSE
CAUTION
  Do not apply accessories, stickers or fi lm to the windscreen near the Forward Sensing
Camera (FSC).
 If the area in front of the Forward Sensing Camera (FSC) lens is obstructed, it will
cause the system to not operate correctly. Consequently, each system may not operate
normally which could lead to an unexpected accident.
  Do not disassemble or modify the Forward Sensing Camera (FSC).  Disassembly or modifi cation of the Forward Sensing Camera (FSC) will cause a
malfunction or mistaken operation. Consequently, each system may not operate
normally which could lead to an unexpected accident.
  Heed the following cautions to assure the correct operation of the Forward Sensing
Camera (FSC).
 


 The direction of the Forward Sensing Camera (FSC) has been fi nely adjusted,
therefore do not change the installation position or remove the Forward Sensing
Camera (FSC).
 


 Be careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get
dirty.
 


 Do not remove the Forward Sensing Camera (FSC) cover.



 Do not place objects on the instrument panel which refl ect light.



 Always keep the windscreen glass around the camera clean by removing dirt or
fogging. Use the windscreen defroster to remove fogging on the windscreen.
 


 Consult an expert repairer, we recommend an Authorised Mazda Repairer regarding
cleaning the interior side of the windscreen around the Forward Sensing Camera
(FSC).
 


 Consult an expert repairer, we recommend an Authorised Mazda Repairer before
performing repairs around the Forward Sensing Camera (FSC).
 


 The Forward Sensing Camera (FSC) is installed to the windscreen. Consult an expert
repairer, we recommend an Authorised Mazda Repairer for windscreen repair and
replacement.
 


 When performing repairs around the rearview mirror, consult an expert repairer, we
recommend an Authorised Mazda Repairer.
 


 Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area
around it. If strong force is applied, stop using the Lane Departure Warning System
(LDWS), the High Beam Control System (HBC), and the Smart Brake Support
(SBS) and consult an expert repairer, we recommend an Authorised Mazda Repairer.
 


 The direction in which the Forward Sensing Camera (FSC) is pointed has been fi nely
adjusted. Do not change the installation position of the Forward Sensing Camera
(FSC) or remove it. Otherwise, it could result in damage or malfunction.
$9@&;&&%@&EJUJPOJOEC







4–150
When Driving
i-ACTIVSENSE
NOTE
  In the following cases, the Forward Sensing Camera (FSC) cannot detect target objects
correctly, and each system may be unable to operate normally.
 


 The height of the vehicle ahead is low.



 You drive your vehicle at the same speed as the vehicle ahead.



 Headlights are not turned on during the night or when going through a tunnel. 

 In the following cases, the Forward Sensing Camera (FSC) may not be able to detect
target objects correctly.
 


 When driving next to walls with no patterning (including fences and longitudinally
striped walls).
 


 The tail lights of the vehicle ahead are turned off.



 A vehicle is outside the illumination range of the headlights.



 The vehicle is making a sharp curve, or ascending or descending a steep slope.



 Entering or exiting a tunnel.



 Heavy luggage is loaded causing the vehicle to tilt.



 Strong light is shone at the front of the vehicle (back light or high-beam light from
on-coming vehicles).
 


 There are many light emitters on the vehicle ahead.



 When the vehicle ahead is not equipped with tail lights or the tail lights are turned
off at nighttime.
 


 The vehicle ahead has a special shape.
$9@&;&&%@&EJUJPOJOEC







4–170
When Driving
Rear View Monitor
Displayable Range on the Screen
The images on the screen may be different from the actual conditions.
(Screen display)
Garnish
Bumper
(Actual view)
Object
NOTE
  The displayable range varies depending on the vehicle and road conditions. 
 The displayable range is limited. Objects under the bumper or around the bumper ends
cannot be displayed.
  The distance appearing in the displayed image is different from the actual distance
because the rear view parking camera is equipped with a specifi c lens.

 Some optionally installed vehicle accessories may be picked up by the camera. Do not
install any optional parts that can interfere with the camera view, such as illuminating
parts or parts made of refl ective material.

 It may be diffi cult to see the display under the following conditions, however, it does
not indicate a malfunction.
 


 In darkened areas.



 When the temperature around the lens is high/low.



 When the camera is wet such as on a rainy day or during periods of high humidity.



 When foreign material such as mud is stuck around the camera.



 When the camera lens refl ects sunlight or headlight beams. 

 Image display may be delayed if the temperature around the camera is low.
$9@&;&&%@&EJUJPOJOEC







*Some models.6–47
Maintenance and Care
Owner Maintenance
Headlights (Low beam)
Headlights (High beam)
Headlights (High beam)/Running lights *
Running lights/Position lights
Position lights
Front fog lights *
Front direction indicator lights
Side direction indicator lights
Brake lights/Tail lights
Rear direction indicator lights
Tail lights *
Reverse lights
Rear fog light (Left-hand drive model) *
Rear fog light (Right-hand drive model) *
High-mount brake light
Number plate lights
Overhead lights (Front)/Map lights
Overhead lights (Rear)
Luggage compartment light
$9@&;&&%@&EJUJPOJOEC