2015 MAZDA MODEL CX-3 brake

4–149
When Driving
i-ACTIVSENSE
CAUTION
  Do not apply accessories, stickers or fi lm to the windscreen near the Forward Sensing
Camera (FSC).
 If the area in front of the Forward Sensing Camera (FSC) lens is obstructed, it will
cause the system to not operate correctly. Consequently, each system may not operate
normally which could lead to an unexpected accident.
  Do not disassemble or modify the Forward Sensing Camera (FSC).  Disassembly or modifi cation of the Forward Sensing Camera (FSC) will cause a
malfunction or mistaken operation. Consequently, each system may not operate
normally which could lead to an unexpected accident.
  Heed the following cautions to assure the correct operation of the Forward Sensing
Camera (FSC).
 


 The direction of the Forward Sensing Camera (FSC) has been fi nely adjusted,
therefore do not change the installation position or remove the Forward Sensing
Camera (FSC).
 


 Be careful not to scratch the Forward Sensing Camera (FSC) lens or allow it to get
dirty.
 


 Do not remove the Forward Sensing Camera (FSC) cover.



 Do not place objects on the instrument panel which refl ect light.



 Always keep the windscreen glass around the camera clean by removing dirt or
fogging. Use the windscreen defroster to remove fogging on the windscreen.
 


 Consult an expert repairer, we recommend an Authorised Mazda Repairer regarding
cleaning the interior side of the windscreen around the Forward Sensing Camera
(FSC).
 


 Consult an expert repairer, we recommend an Authorised Mazda Repairer before
performing repairs around the Forward Sensing Camera (FSC).
 


 The Forward Sensing Camera (FSC) is installed to the windscreen. Consult an expert
repairer, we recommend an Authorised Mazda Repairer for windscreen repair and
replacement.
 


 When performing repairs around the rearview mirror, consult an expert repairer, we
recommend an Authorised Mazda Repairer.
 


 Do not hit or apply strong force to the Forward Sensing Camera (FSC) or the area
around it. If strong force is applied, stop using the Lane Departure Warning System
(LDWS), the High Beam Control System (HBC), and the Smart Brake Support
(SBS) and consult an expert repairer, we recommend an Authorised Mazda Repairer.
 


 The direction in which the Forward Sensing Camera (FSC) is pointed has been fi nely
adjusted. Do not change the installation position of the Forward Sensing Camera
(FSC) or remove it. Otherwise, it could result in damage or malfunction.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–151
When Driving
i-ACTIVSENSE
Radar Sensor (Front) *
Your vehicle is equipped with a radar sensor (front).
The following systems also use the radar sensor (front).
 


 Mazda Radar Cruise Control (MRCC)



 Distance Recognition Support System (DRSS)



 Smart Brake Support (SBS)
The radar sensor (front) functions by detecting the radio waves refl ected off a vehicle ahead
or an obstruction sent from the radar sensor.
The radar sensor (front) is mounted behind the front emblem.
Radar sensor (front)
If the Smart Brake Support/Smart City Brake Support (SBS/SCBS) Warning Light (amber)
is illuminated, the area around the radar sensor may be dirty. Refer to “Warning Guidance”
in the centre display (Type C/D audio).
Refer to If a Warning Light Turns On or Flashes on page 7-35 .
$9@&;&&%@&EJUJPOJOEC







4–153
When Driving
i-ACTIVSENSE
NOTE
  Under the following conditions,
the radar sensor (front) may not
be able to detect vehicles ahead
or obstructions correctly and each
system may not operate normally.
 


 The rear surface of a vehicle
ahead does not refl ect radio waves
effectively, such as an unloaded
trailer or an automobile with a
loading platform covered by a
soft top, vehicles with a hard
plastic tailgate, and round-shaped
vehicles.
 


 Vehicles ahead with low vehicle
height and thus less area for
refl ecting radio waves.




 Visibility is reduced due to a
vehicle ahead casting off water,
snow, or sand from its tyres and
onto your windscreen.
 


 The luggage compartment is
loaded with heavy objects or the
rear passenger seats are occupied.
 


 Ice, snow, or soiling is on the front
surface of the front emblem.
 


 During inclement weather such as
rain, snow, or sand storms.
 


 When driving near facilities or
objects emitting strong radio
waves.
NOTE
  Under the following conditions,
the radar sensor (front) may not
be able to detect vehicles ahead or
obstructions.
 


 The beginning and end of a curve.



 Roads with continuous curves.



 Narrow lane roads due to road
construction or lane closures.
 


 The vehicle ahead enters the radar
sensor's blind spot.
 


 The vehicle ahead is running
abnormally due to accident or
vehicle damage.
 


 Roads with repeated up and down
slopes
 


 Driving on poor roads or unpaved
roads.
 


 The distance between your vehicle
and the vehicle ahead is extremely
short.
 


 A vehicle suddenly comes close
such as by cutting into the lane.


 To prevent incorrect operation of
the system, use tyres of the same
specifi ed size, manufacturer, brand,
and tread pattern on all four wheels.
In addition, do not use tyres with
signifi cantly different wear patterns
or tyre pressures on the same vehicle
(Including the temporary spare tyre).
  If the battery power is weak, the
system may not operate correctly.
  When driving on roads with little
traffi c and few vehicles ahead or
obstructions for the radar sensor to
detect, Smart Brake Support/Smart
City Brake Support (SBS/SCBS)
Warning Light (amber) temporarily
illuminates, however, this does not
indicate a problem.
$9@&;&&%@&EJUJPOJOEC







*Some models.4–154
When Driving
i-ACTIVSENSE
Laser Sensor (Front) *
Your vehicle is equipped with a laser sensor (front). The laser sensor (front) is positioned
near the rearview mirror and used by the following systems.
 


 Smart Brake Support (SBS)



 Smart City Brake Support (SCBS)
Laser sensor (front)
CAUTION
Heed the following precautions to assure correct operation of the system.


 Keep the windscreen clean at all times. 
 Do not apply stickers to the surface of the windscreen (including transparent stickers). 
 If cracks or damage caused by fl ying gravel or debris is visible near the laser sensor
(front), stop using the system immediately and have your vehicle inspected by an
Authorised Mazda Repairer.
 See the next page on how to turn off the system. Refer to Personalisation Features on
page 9-13 .
  Do not apply a coating agent to the windscreen. 
 When replacing the windscreen wipers or windscreen, consult an Authorised Mazda
Repairer.
  Never remove the sensor. 
 A removed sensor will not meet the conditions for a class 1M laser under the IEC
60825-1 specifi cation and therefore eye safety cannot be assured.

 Do not peer into the sensor using optical instruments with a magnifi cation function
such as magnifying glasses, and microscopic and objective lenses within a distance of
100 mm (3.94 in) from the sensor.
$9@&;&&%@&EJUJPOJOEC







4–160
When Driving
Cruise Control
3. Set the cruise control by pressing the
SET
or SET switch at the desired
speed. The cruise control is set at the
moment the SET
or SET switch is
pressed. Release the accelerator pedal
simultaneously. The cruise set indicator
light (Green) illuminates.
NOTE
  The cruise control speed setting
cannot be performed under the
following conditions:
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.


 Release the SET or SET switch
at the desired speed, otherwise the
speed will continue increasing while
the SET
switch is pressed and
held, and continue decreasing while
the SET
switch is pressed and held
(except when the accelerator pedal is
depressed).
  On a steep grade, the vehicle may
momentarily slow down while
ascending, or speed up while
descending.
NOTE
  Cruise control will cancel if the
vehicle speed decreases below
21 km/h (13 mph) when cruise is
activated, such as when climbing a
steep grade.
  Cruise control may cancel at about
15 km/h (9 mph) below the preset
speed (such as may happen when
climbing a long, steep grade).
To Increase Cruising Speed
Follow either of these procedures.
To increase speed using cruise control
switch
Press the SET
switch and hold it. Your
vehicle will accelerate. Release the switch
at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will increase the
preset speed according to the number of
times it is operated.
Increasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To increase speed using accelerator
pedal
Depress the accelerator pedal to accelerate
to the desired speed. Press the SET
or
SET
switch and release it immediately.
$9@&;&&%@&EJUJPOJOEC







4–161
When Driving
Cruise Control
NOTE
Accelerate if you want to speed up
temporarily when the cruise control is
on. Greater speed will not interfere with
or change the set speed. Take your foot
off the accelerator to return to the set
speed.
To Decrease Cruising Speed
Press the SET switch and hold it. The
vehicle will gradually slow.
Release the switch at the speed you want.
Press the SET
switch and release it
immediately to adjust the preset speed.
Multiple operations will decrease the
preset speed according to the number of
times it is operated.
Decreasing speed with a single SET
switch operation
Meter display for vehicle speed indicated
in km/h: 1 km/h (0.6 mph)
Meter display for vehicle speed indicated
in mph: 1 mph (1.6 km/h)
To Resume Cruising Speed at
More Than 25 km/h (16 mph)
If some other method besides the OFF
switch was used to cancel cruising speed
(such as applying the brake pedal) and the
system is still activated, the most recent
set speed will automatically resume when
the RESUME switch is pressed.
If vehicle speed is below 25 km/h (16
mph), increase the vehicle speed up to
25 km/h (16 mph) or more and press the
RESUME switch.
To Temporarily Cancel
To temporarily cancel the system, use one
of these methods:
 


 Slightly depress the brake pedal.



(Manual transaxle)
 Depress the clutch pedal.



 Press the CANCEL switch.
If the RESUME switch is pressed when
the vehicle speed is 25 km/h (16 mph) or
higher, the system reverts to the previously
set speed.
NOTE
  If any of the following conditions
occur, the cruise control system is
temporarily cancelled.
 


 The parking brake is applied.



(Vehicles with adjustable speed
limiter)
  The ON/OFF switch for the
adjustable speed limiter is pressed.
 


(Automatic transaxle)
 The selector lever is in the P or N
position.
 


(Manual transaxle)
 The shift lever is in the neutral
position.
 
 When the cruise control system is
temporarily cancelled by even one of
the applicable cancel conditions, the
speed cannot be re-set.
 (Automatic transaxle) The cruise control cannot be
cancelled while driving in manual
mode (selector lever shifted from
D to M position). Therefore, engine
braking will not be applied even
if the transaxle is shifted down
to a lower gear. If deceleration is
required, lower the set speed or
depress the brake pedal.
$9@&;&&%@&EJUJPOJOEC







4–16 6
When Driving
Tyre Pressure Monitoring System
Tyre Pressure Monitoring System
Initialization
In the following cases, system
initialization must be performed so that the
system operates normally.
 


 A tyre pressure is adjusted.



 Tyre rotation is performed.



 A tyre or wheel is replaced.



 The battery is replaced or completely
drained.
 


 The tyre pressure monitoring system
warning light is illuminated.
Initialization method
1. Park the car in a safe place and fi rmly
apply the parking brake.
2. Let the tyres cool, then adjust the tyre
pressure of all four (4) tyres to the
specifi ed pressure indicated on the tyre
pressure label located on the door jamb
of the driver's door (door open).
Refer to Tyres on page 9-9 .
3. Switch the ignition ON.
4. While the vehicle is parked, press
and hold the tyre pressure monitoring
system set switch and verify that
the tyre pressure monitoring system
warning light in the instrument cluster
fl ashes twice and a beep sound is heard
once.
CAUTION
If the system initialization is performed
without adjusting the tyre pressure, the
system cannot detect the normal tyre
pressure and it may not illuminate the
tyre pressure monitoring system warning
light even if a tyre pressure is low, or
it may illuminate the light even if the
pressures are normal.
Adjust the tyre pressure on all four
tyres and initialize the system when
the warning light is turned on. If the
warning light turns on for a reason other
than a fl at tyre, the tyre pressure of all
four tyres may have decreased naturally.
The system initialization will not be
performed if the switch is pressed while
the vehicle is being driven.
$9@&;&&%@&EJUJPOJOEC







4–178
When Driving
Parking Sensor System
NOTE
  Do not install any accessories within the detection ranges of the sensors. It may affect
the system operation.
  Depending on the type of obstruction and the surrounding conditions, the detection
range of a sensor may narrow, or the sensors may not be able to detect obstructions.
  The system may not operate normally under the following conditions:




 Mud, ice, or snow is adhering to the sensor area (Returns to normal operation when
removed).
 


 The sensor area is frozen (Returns to normal operation when the ice is thawed).



 The sensor is covered by a hand.



 The sensor is excessively shocked.



 The vehicle is excessively tilted.



 Under extremely hot or cold weather conditions.



 The vehicle is driven on bumps, inclines, gravel, or grass covered roads.



 Anything which generates ultrasound is near the vehicle, such as another vehicle's
horn, the engine sound of a motorcycle, the air brake sound of a large-sized vehicle,
or another vehicle's sensors.
 


 The vehicle is driven in heavy rain or in road conditions causing water-splash.



 A commercially-available wing pole or an aerial for a radio transmitter is installed to
the vehicle.
 


 The vehicle is moving towards a tall or square curbstone.



 An obstruction is too close to the sensor. 

 Obstructions under the bumper may not be detected. Obstructions that are lower than
the bumper or thin which may have been initially detected but are no longer detected
as the vehicle approaches more closely.
  The following types of obstructions may not be detected:




 Thin objects such as wire or rope



 Things which absorb sonic waves easily such as cotton or snow



 Angular shaped objects



 Very tall objects, and those which are wide at the top



 Small, short objects 

 Always have the system inspected at an expert repairer, we recommend an Authorised
Mazda Repairer if any shock is applied to the bumpers, even in a minor accident. If the
sensors are deviated, they cannot detect obstructions.
  The system may have a malfunction if the beep does not operate. Consult an expert
repairer, we recommend an Authorised Mazda Repairer.
  The beeper which indicates a system malfunction may not be heard if the ambient
temperature is extremely cold, or mud, ice, or snow adheres to the sensor area.
Remove any foreign material from the sensor area.
  When installing a trailer hitch, consult an expert repairer, we recommend an
Authorised Mazda Repairer.
$9@&;&&%@&EJUJPOJOEC