2015 MAZDA MODEL 6 warning

Black plate (495,1)
qIf the tire pressure monitoring
system warning light flashes
If the tire pressure monitoring system has
a malfunction, the tire pressure warning
light flashes for about 1 minute when the
ignition is switched ON and then
continues illuminating. Have your vehicle
checked by an Authorized Mazda Dealer
as soon as possible.
qIf the KEY indication/warning
light (red) is indicated
Type A
“Keyless System Inspection Required”
is displayed
This message is displayed if the advanced
keyless entry & push button start system
has a problem.
Contact an Authorized Mazda Dealer.
CAUTION
If the above message is indicated, or
the push button start indicator light
(amber) flashes, the engine may not
start. If the engine cannot be started,
try starting it using the emergency
operation for starting the engine, and
have the vehicle inspected at an
Authorized Mazda Dealer as soon as
possible.
Refer to Emergency Operation for
Starting the Engine on page 4-8.
“Set Power to OFF”is displayed
This message is displayed when the
driver's door is opened without switching
the ignition off.
“Key not found”is displayed
This message is displayed when any of
the following operations is performed
with the key out of the operational range
or placed in areas inside the cabin where it
is difficult for the key to be detected.
lThe push button start is pressed with
the ignition switched off
lThe ignition is switched onlAll doors are closed without switching
the ignition off
Type B
If any malfunction occurs in the keyless
entry system, it illuminates continuously.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-35
Mazda6_8DQ8-EA-13L_Edition3 Page495
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (496,1)
CAUTION
If the key warning indicator light
illuminates or the push button start
indicator light (amber) flashes, the
engine may not start. If the engine
cannot be started, try starting it
using the emergency operation for
starting the engine, and have the
vehicle inspected at an Authorized
Mazda Dealer as soon as possible.
Refer to Emergency Operation for
Starting the Engine on page 4-8.
qIf the high beam control system
(HBC) warning light (amber)
flashes
í
This light flashes if there is a malfunction
in the high beam control system (HBC).
Have your vehicle inspected by an
Authorized Mazda Dealer.
qIf the traction control system
(TCS)/dynamic stability control
(DSC) indicator light illuminates
If the light stays on, the TCS, DSC or the
brake assist system may have a
malfunction and they may not operate
correctly. Take your vehicle to an
Authorized Mazda Dealer.
NOTE
lIn addition to the indicator light flashing, a
slight lugging sound will come from the
engine. This indicates that the TCS/DSC is
operating properly.
lOn slippery surfaces, such as fresh snow, it
will be impossible to achieve high rpm
when the TCS is on.
qIf the dynamic stability control
system (DSC) OFF indicator light
illuminates
If the light remains illuminated and the
TCS/DSC is not switched off, take your
vehicle to an Authorized Mazda Dealer.
The DSC may have a malfunction.
7-36
If Trouble Arises
íSome models.
Warning/Indicator Lights and Warning Sounds
Mazda6_8DQ8-EA-13L_Edition3 Page496
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (497,1)
qIf the adaptive front lighting system
(AFS) OFF indicator light flashesí
The indicator light flashes continuously if
the system is malfunctioning. Consult an
Authorized Mazda Dealer.
NOTE
lEven if the AFS is not operating due to
some malfunction, the normal headlight
function is still operable.
lIf there is a malfunction with the headlight
auto-leveling function, the indicator light
flashes.
qIf the low engine coolant
temperature indicator light (blue)
does not turn off
If the low engine coolant temperature
indicator light remains illuminated after
the engine has been sufficiently warmed
up, the temperature sensor could have a
malfunction. Consult an Authorized
Mazda Dealer.
qIf the turn signal/hazard warning
indicator light illuminates or flashes
at an abnormally high speed
If an indicator light remains illuminated
(does not flash) or if it flashes abnormally,
one of the turn signal bulbs may be
burned out. Consult an Authorized Mazda
Dealer.
qIf the security indicator light
illuminates or flashes
If the engine does not start with the
correct key, and the security indicator
light keeps illuminating or flashing, the
system may have a malfunction. Consult
an Authorized Mazda Dealer.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-37íSome models. Mazda6_8DQ8-EA-13L_Edition3 Page497
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (498,1)
qIf the blind spot monitoring (BSM)
system OFF indicator light flashesí
The indicator light flashes if the BSM
system has a malfunction. Consult an
Authorized Mazda Dealer.
NOTE
If the vehicle is driven on a road with less
traffic and few vehicles that the radar sensors
can detect, the system may pause (The BSM
OFF indicator light in the instrument panel
flashes). However, it does not indicate a
malfunction.
qIf the lights-on indicator light flashes
The light continues to flash if the lighting
system has a malfunction. Consult an
Authorized Mazda Dealer.
Warning Sound is Activated
qLights-On Reminder
The lights-on reminder is operable when
the time setting*1of the auto headlight off
function is 0 seconds.
If lights are on and the ignition is
switched to ACC or the ignition is
switched off, a continuous beep sound
will be heard when the driver's door is
opened.
*1 If the light switch is left on, the auto
headlight off function automatically
turns off the lights about 30 seconds
after switching the ignition off. The
time setting can be changed.
Refer to Personalization Features on
page 9-9.
NOTE
lWhen the ignition is switched to ACC, the
“Ignition Not Switched Off (STOP)
Warning Beep”(page 7-39) overrides the
lights-on reminder.
lA personalized function is available to
change the sound volume for the lights-on
reminder.
Refer to Personalization Features on page
9-9.
7-38
If Trouble Arises
íSome models.
Warning/Indicator Lights and Warning Sounds
Mazda6_8DQ8-EA-13L_Edition3 Page498
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (499,1)
qAir Bag/Front Seat Belt
Pretensioner System Warning Beep
If a malfunction is detected in the air bag/
front seat belt pretensioner systems and
the warning light, a warning beep sound
will be heard for about 5 seconds every
minute.
The air bag and seat belt pretensioner
system warning beep sound will continue
to be heard for approximately 35 minutes.
Have your vehicle inspected at an
Authorized Mazda Dealer as soon as
possible.
WARNING
Do not drive the vehicle with the air
bag/front seat belt pretensioner system
warning beep sounding:
Driving the vehicle with the air bag/
front seat belt pretensioner system
warning beep sounding is dangerous.
In a collision, the air bags and the
front seat belt pretensioner system
will not deploy and this could result
in death or serious injury.
Contact an Authorized Mazda Dealer
to have the vehicle inspected as soon
as possible.
qSeat Belt Warning Beep
If the driver's seat belt is not fastened
when the ignition is switched ON, a beep
sound will be heard for about 6 seconds.
If the driver or the front passenger's seat
belt is not fastened and the vehicle is
driven at a speed faster than about 20
km/h (12 mph), a beep sound will be
heard again for a specified period of time.NOTE
lSome models do not have the seat belt
warning function for the front passenger's
seat.
lPlacing heavy items on the front passenger
seat may cause the front passenger seat belt
warning function to operate depending on
the weight of the item.
lTo allow the front passenger seat weight
sensor to function properly, do not place
and sit on an additional seat cushion on the
front passenger seat. The sensor may not
function properly because the additional
seat cushion could cause sensor
interference.
lWhen a small child sits on the front
passenger seat, it is possible that the
warning beep will not operate.
qIgnition Not Switched Off
(STOP) Warning Beep
If the driver's door is opened while the
ignition is switched to ACC, a continuous
beep sound will be heard to notify the
driver that the ignition has not been
switched off (STOP) (for vehicles with a
type A meter, messages are displayed in
the instrument cluster). Left in this
condition, the keyless entry system will
not operate, the car cannot be locked, and
the battery power will be depleted.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-39
Mazda6_8DQ8-EA-13L_Edition3 Page499
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (500,1)
qKey Removed from Vehicle
Warning Beep
Under the following conditions, a beep
sound will be heard and the KEY warning
light (red) will flash continuously when
the ignition has not been switched off to
notify the driver that the key has been
removed (for vehicles with a type A
meter, messages are displayed in the
instrument cluster). The KEY warning
light (red) will stop flashing when the key
is back inside the vehicle (for vehicles
with a type A meter, messages are
displayed in the instrument cluster):
The ignition has not been switched off
and all the doors are closed after
removing the key from the vehicle. (A
beep sound will be heard 6 times.)
NOTE
Because the key utilizes low-intensity radio
waves, the Key Removed From Vehicle
Warning may activate if the key is carried
together with a metal object or it is placed in a
poor signal reception area.
qRequest Switch Inoperable
Warning Beep (With the
advanced keyless function)
If the request switch is pressed under the
following conditions while the key is
being carried, a beep will be heard for
about 2 seconds to indicate that the front
doors and the trunk can not be locked.
lA door is open (door ajar included).lThe ignition has not been switched to
off.
qKey Left-in-trunk Warning Beep
(With the advanced keyless function)
If the key is left in the trunk with all doors
locked and the trunk lid closed, a beep
sound is heard for about 10 seconds to
remind the driver the key has been left in
the trunk. If this happens, open the trunk
lid by pressing the electric trunk lid
opener and remove the key. A key
removed from the trunk may not function
because its functions may have been
temporarily suspended. To restore the key
function, perform the applicable
procedure (page 3-7).
qKey Left-in-vehicle Warning Beep
(With the advanced keyless function)
If a key is left in the vehicle cabin and all
the doors and the trunk are locked using a
separate key, a beep sound is heard for
about 10 seconds to remind the driver that
the key has been left in the vehicle cabin.
If this happens, the doors and the trunk
lock but the functions of the key left in the
vehicle cabin may be temporarily
suspended.
Perform the applicable procedure to
restore the functions of the key (page 3-7).
qi-ELOOP Warning Beep
If the vehicle is driven while“i-ELOOP
charging”is displayed, a beep sound is
heard. Make sure the message is no longer
displayed before driving.
qTire Inflation Pressure Warning
Beep
The warning beep sound will be heard for
about 3 seconds when there is any
abnormality in tire inflation pressures
(page 4-117).
7-40
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
Mazda6_8DQ8-EA-13L_Edition3 Page500
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (501,1)
qLane Departure Warning System
(LDWS) Warning Soundí
While the system is operating, if the
system determines that the vehicle may
depart from the lane, it sounds a warning
sound.
NOTE
lThe volume of the LDWS warning sound
can be changed.
Refer to Personalization Features on page
9-9.
lThe type of the LDWS warning sound can
be changed.
Refer to Personalization Features on page
9-9.
qBlind Spot Monitoring (BSM)
System Warning Beepí
Driving forward
The warning beep operates when the turn
signal lever is operated to the side where
the BSM warning light is illuminated.
NOTE
A personalized function is available to change
the BSM warning beep sound volume. Refer to
Personalization Features on page 9-9.
Reversing
If vehicles approach from the rear on the
left and right, the Blind Spot Monitoring
(BSM) warning beep operates.
qMazda Radar Cruise Control
(MRCC) System Warningsí
The Mazda Radar Cruise Control
(MRCC) system warnings notify the
driver of system malfunctions and
cautions on use when required.
Check based on the beep sound.
Cautions What to check
The beep sounds 1 time
while the Mazda Radar
Cruise Control (MRCC)
is operatingThe vehicle speed is
slower than 25 km/h
(16 mph) and the Mazda
Radar Cruise Control
(MRCC) system has been
canceled.
The beep sounds 5 times
while drivingThe distance between
your vehicle and the
vehicle ahead is too
close. Verify the safety of
the surrounding area and
reduce vehicle speed.
When the Mazda Radar
Cruise Control (MRCC)
is operating, the beep
sounds and the Mazda
Radar Cruise Control
(MRCC) warning light
(amber) in the instrument
cluster flashes.A malfunction in the
system may be indicated.
Have your vehicle
inspected at an
Authorized Mazda
Dealer.
qCollision warningí
If there is the possibility of a collision
with a vehicle or obstruction ahead, the
beep sounds continuously and a warning
is indicated in the display.
If Trouble Arises
Warning/Indicator Lights and Warning Sounds
7-41íSome models. Mazda6_8DQ8-EA-13L_Edition3 Page501
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L

Black plate (503,1)
8
Customer Information and Reporting
Safety Defects
Important consumer information including warranties and add-on equipment.
Customer Assistance ............................... 8-2
Customer Assistance (U.S.A.) ............ 8-2
Customer Assistance (Canada) ........... 8-7
Customer Assistance (Puerto Rico) ... 8-10
Customer Assistance (Mexico) ......... 8-11
Mazda Importer/Distributors ............... 8-13
Importer/Distributor .......................... 8-13
Reporting Safety Defects ....................... 8-14
Reporting Safety Defects (U.S.A.) .... 8-14
Reporting Safety Defects (Canada) ... 8-15
Warranty ................................................ 8-16
Warranties for Your Mazda ............... 8-16
Outside the United States/Canada ..... 8-17
Registering Your Vehicle in A Foreign
Country (Except United States and
Canada) ............................................. 8-18
Add-On Non-Genuine Parts and
Accessories ....................................... 8-19
Cell Phones ............................................. 8-20
Cell Phones Warning ......................... 8-20
Event Data Recorder ............................. 8-21
Event Data Recorder (U.S.A. and
Canada) ............................................. 8-21
Recording of Vehicle Data .................... 8-22
Recording of Vehicle Data ................ 8-22
Uniform Tire Quality Grading System
(UTQGS) ................................................ 8-23
Uniform Tire Quality Grading System
(UTQGS) .......................................... 8-23Tire Information (U.S.A.) ..................... 8-25
Tire Labeling ..................................... 8-25
Location of the Tire Label
(Placard) ............................................ 8-31
Tire Maintenance .............................. 8-34
Vehicle Loading ................................ 8-37
Steps for Determining the Correct Load
Limit ................................................. 8-43
Declaration of Conformity .................... 8-44
Declaration of Conformity ................ 8-44
Service Publications .............................. 8-51
Service Publications .......................... 8-51
8-1
Mazda6_8DQ8-EA-13L_Edition3 Page503
Friday, June 13 2014 6:23 PM
Form No.8DQ8-EA-13L