2015 MAZDA MODEL 3 HATCHBACK wheel

6–49
Maintenance and Care
Owner Maintenance
CAUTION
A wrong-sized wheel may adversely
affect:
 
 Tyre fi t 
 Wheel and bearing life 
 Ground clearance 
 Snow-chain clearance 
 Speedometer calibration 
 Headlight aim 
 Bumper height 
 Tyre Pressure Monitoring System
When replacing a wheel, make sure the
new one is the same as the original factory
wheel in diameter, rim width, and offset
(inset/outset).
Proper tyre balancing provides the best
riding comfort and helps reduce tread
wear. Out-of-balance tyres can cause
vibration and uneven wear, such as
cupping and fl at spots.
.B[EB@&'&&"@&EJUJPOJOEC







6–52
Maintenance and Care
Owner Maintenance
WARNING
Do not replace the xenon fusion bulbs
yourself:
Replacing the xenon fusion bulbs
yourself is dangerous. Because the
xenon fusion bulbs require high
voltage, you could receive an electric
shock if the bulbs are handled
incorrectly. Consult an expert repairer,
we recommend an Authorised Mazda
Repairer when the replacement is
necessary.
Never touch the glass portion of a
halogen bulb with your bare hands
and always wear eye protection when
handling or working around the bulbs:
When a halogen bulb breaks, it is
dangerous. These bulbs contain
pressurised gas. If one is broken, it will
explode and serious injuries could be
caused by the fl ying glass.
If the glass portion is touched with bare
hands, body oil could cause the bulb to
overheat and explode when lit.
Always keep halogen bulbs out of the
reach of children:
Playing with a halogen bulb is
dangerous. Serious injuries could be
caused by dropping a halogen bulb or
breaking it some other way.
NOTE
  To replace the bulb, contact an
expert repairer, we recommend an
Authorised Mazda Repairer.
  If the halogen bulb is accidentally
touched, it should be cleaned with
rubbing alcohol before being used.
  Use the protective cover and carton
for the replacement bulb to dispose
of the old bulb promptly and out of
the reach of children.
Replacing Exterior Light Bulbs
Headlights (With xenon fusion
headlights)
Low/High beam bulbs
You cannot replace the low/high beam
bulbs by yourself. The bulbs must
be replaced at an expert repairer, we
recommend an Authorised Mazda
Repairer.
Headlights (With halogen headlights)
Low-beam bulbs
1. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right, and turn
off engine.
2. Make sure the headlight switch is off.
.B[EB@&'&&"@&EJUJPOJOEC







6–55
Maintenance and Care
Owner Maintenance
Running lights/Position lights (With
xenon fusion headlights)
Due to the complexity and diffi culty
of the procedure, the LED bulbs must
be replaced by an expert repairer, we
recommend an Authorised Mazda
Repairer.
NOTE
LED bulb replacement is not possible
because it is built into the unit. Replace
the unit.
Front direction indicator lights, Position
lights (With halogen headlights)
1. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right, and turn
off engine.
2. Make sure the headlight switch is off.
3. Pull the centre of each plastic retainer
and remove the retainers.
Removal
Installation
4. Turn the screw anticlockwise and
remove it, and then partially peel back
the mudguard.
5. Turn the socket and bulb assembly
anticlockwise and remove it.
6. Disconnect the bulb from the socket.
Front direction indicator lights
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–56
Maintenance and Care
Owner Maintenance
Position lights (With halogen
headlights)
7. Install the new bulb in the reverse order
of the removal procedure.
Front fog lights
*
1. If you are changing the right bulb, start
the engine, turn the steering wheel all
the way to the left, and turn off engine.
If you are changing the left bulb, turn
the steering wheel to the right, and turn
off engine.
2. Make sure the fog light switch is off.
3. Pull the centre of each plastic retainer
and remove the retainers.
Removal
Installation
4. Turn the screw anticlockwise and
remove it, and then partially peel back
the mudguard.
5. Disconnect the connector from the unit
by pressing the tab on the connector
with your fi nger and pulling the
connector downward.
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.6–76
Maintenance and Care
Appearance Care
Bright-Metal Maintenance














 Use tar remover to remove road tar and
insects. Never do this with a knife or
similar tool.
 


 To prevent corrosion on bright-
metal surfaces, apply wax or chrome
preservative and rub it to a high lustre.
 


 During cold weather or in coastal areas,
cover bright-metal parts with a coating
of wax or preservative heavier than
usual. It would also help to coat them
with noncorrosive petroleum jelly or
some other protective compound.
CAUTION
Do not use steel wool, abrasive cleaners,
or strong detergents containing highly
alkaline or caustic agents on chrome-
plated or anodised aluminium parts. This
may result in damage to the protective
coating and cause discolouration or
paint deterioration.
Undercoating
This special coating is applied to the
critical parts of the underside to protect
vehicles from damage caused by
chemicals or stones. This coating is liable
to be damaged with time. Check this
coating periodically.
An expert repairer, we recommend an
Authorised Mazda Repairer are well
informed on how repairs should be made.
Consult an expert repairer, we recommend
an Authorised Mazda Repairer.
Aluminium Wheel Maintenance *
A protective coating is provided over the
aluminium wheels. Special care is needed
to protect this coating.
CAUTION
Do not use any detergent other than mild
detergent. Before using any detergent,
verify the ingredients. Otherwise, the
product could discolour or stain the
aluminium wheels.
NOTE
  Do not use a wire brush or any
abrasive cleaner, polishing
compound, or solvent on aluminium
wheels. They may damage the
coating.
  Always use a sponge or soft cloth to
clean the wheels.
 Rinse the wheels thoroughly with
lukewarm or cold water. Also, be
sure to clean the wheels after driving
on dusty or salted roads to help
prevent corrosion.
  Avoid washing your vehicle in an
automatic car wash that uses high-
speed or hard brushes.
.B[EB@&'&&"@&EJUJPOJOEC







7–3
If Trouble Arises
Flat Tyre
Spare Tyre and Tool Storage
Spare tyre and tools are stored in the locations illustrated in the diagram.
Towing eyelet
Spare
tyreJack Spare tyre hold-down bolt
Tool bag (With spare tyre (except Saudi Arabia))
Towing eyelet
Jack lever (Without spare tyre) Saloon
Puncture Tyre Repair Kit
Wheel brace
Some models.
Towing eyelet
Wheel brace
Spare tyre Jack
Jack lever Spare tyre hold-down bolt
Tool bag (With spare tyre (Saudi Arabia))
Screwdriver
Wrench Wheel braceJack lever
Screwdriver
Wrench
.B[EB@&'&&"@&EJUJPOJOEC







7–4
If Trouble Arises
Flat Tyre
(With spare tyre)
Towing eyeletPuncture Tyre Repair Kit
Jack lever (Without spare tyre)
Towing eyelet
Jack lever Wheel brace
Spare tyre Jack Spare tyre hold-down bolt Hatchback
Wheel brace
Some models.
Tool bag Screwdriver
Wrench
.B[EB@&'&&"@&EJUJPOJOEC







*Some models.7–5
If Trouble Arises
Flat Tyre
Jack *
NOTE
Your vehicle may or may not be
equipped with a jack and wheel brace.
For details, consult an Authorised
Mazda Dealer.
To remove the jack
1 . (Saloon)
Push the tabs and remove the cover.
Tabs
(Hatchback)
Turn the knob and remove the cover.
2. Turn the wing bolt and jack screw
anticlockwise.
To secure the jack
1. Insert the wing bolt into the jack with
the jack screw pointing to the down
and turn the wing bolt clockwise to
temporarily tighten it.
2. Turn the jack screw in the direction
shown in the fi gure.
3. Turn the wing bolt completely to secure
the jack.
NOTE
If the jack is not completely secured, it
could rattle while driving. Make sure the
jack screw is suffi ciently tightened.
.B[EB@&'&&"@&EJUJPOJOEC