2015 Lancia Ypsilon ECU

Never leave children in the unattended car. Always
remove the ignition key when leaving the car and
take it out with you.
WARNING
The car should be braked after a few
clicks of the lever, if it is not, contact
a Lancia Dealership to have it adjusted.
157
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
PARKING
Switch off the engine and engage the handbrake.
Engage a gear (first gear if parked uphill or
reverse if facing downhill) and leave the wheels
turned. If the car is parked on a steep slope block
the wheels with a wedge or stone. Always remove
the ignition key when leaving the car.
HANDBRAKE
To engage the handbrake pull lever A fig. 112
upwards until the car is secured. To release the
handbrake, raise the lever A slightly, press and
hold the button B and lower the lever.
If the car is parked on a steep slope, it is also
advisable to block the wheels with a wedge or
stone.
fig. 112L0F0074

187
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
The sealing fluid has an expiry date.
WARNING
Never operate the compressor for
longer than 20 consecutive minutes.
Risk of overheating. The Fix&Go kit is not
suitable for definitive repairs, so the
repaired tyres may only be used temporarily.
WARNING
The bottle contains ethylene glycol. It
contains latex that might cause
allergic reactions. It is harmful if swallowed.
It is irritant for the eyes. May cause a
reaction if inhaled or on contact. Avoid
contact with eyes, skin and clothes. In the
event of contact, wash immediately with
plenty of water. If ingested, do not induce
vomiting. Rinse out your mouth, drink large
quantities of water and seek immediate
medical attention. Keep out of the reach of
children. The product must not be used
by asthmatics. Do not inhale the vapours
during insertion and suction. Call a doctor
immediately if allergic reactions are noted.
Store the spray bottle away from heat
sources. The sealing fluid has an expiry
date.
Replace the bottle if the sealing fluid
has expired. Dispose of the bottle
and the sealant liquid properly. Have
the sealing fluid and the bottle disposed of in
compliance with national and local
regulations.
INFLATION PROCEDURE
WARNING
Wear the protective gloves provided
with the Fix&Go kit.
To carry out the inflation procedure proceed as
follows:
❒engage the handbrake;
❒place the Fix&Go kit close to the tyre to be
repaired;
❒locate the filler pipe fig. 124 already
connected to the spray bottle A;
❒open the side lid E fig. 125 then connect the
spray bottle A to the fitting, following the
direction of the arrow;
❒undo the cap of the tyre valve F and connect the
filling pipe B tightening the relevant ring nut on
the tyre valve;
❒Make sure that the switch G fig. 126 is in position
0(off), then start the engine;

NUMBER PLATE LIGHTS
To replace the bulbs proceed as follows:
❒remove lens A fig. 141;
❒turn the bulb holder B fig. 142 anticlockwise,
extract the bulb C and replace it;
❒refit the lens.REPLACING INTERIOR BULBS
For the type of bulb and corresponding power
rating, see the paragraph "Changing a bulb".
FRONT ROOF LIGHT
To change the bulbs, proceed as follows:
❒remove the roof light A fig. 143 working at the
points indicated by the arrows;
❒open the flap B fig. 144 and replace the bulbs C
releasing them from the side contacts. Make
sure that the new bulbs are correctly secured
between the contacts;
❒reclose the flap B fig. 144 and fix the roof light
A fig. 143 in its housing making sure that it is
locked.
fig. 141L0F0259fig. 142L0F0214
201
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

SUSPENSION
Versions Front Rear
0.9 TwinAir 85 HP
Independent, MacPherson type with
lower transversal wishbones secured to
an auxiliary crossmemberInterconnected wheels by means of tor-
sion beam 1.2 8V 69 HP
1.3 16V MultiJet
STEERING
Versions Turning circle (m) Type
0.9 TwinAir 85 HP9.4
Rack and pinion with electric power
steering 1.2 8V 69 HP9.4
1.3 16V MultiJet9.4
247
GETTING TO KNOW
YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTS
AND MESSAGES
IN AN EMERGENCY
SERVICING AND
MAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX

Possible error messages
If the CD loaded cannot be read (e.g. a CD ROM
has been inserted or the CD is inserted the wrong
way round or there is reading error) the display
will show the wording "CD Disc error".
The CD will then be ejected and the audio source
activated prior to the CD mode selection will be
heard.
With an external audio source activated (TA,
ALARM or Phone), the CD that cannot be read
will be not be ejected until these functions have
ended. At the end, with the CD mode activated,
the display will show the text "CD Disc error" for
a few seconds and then the CD will be ejected.
If the CD player overheats the CD playing could
be temporarily interrupted. The radio will
automatically turn to the Radio (Tuner) mode and
the display will show “CD hot” and then “CD disc
error”.DISPLAY INFORMATION
When the CD player is in operation, information
appears on the display with the following
meanings:
❒"CD Track 5": indicates the number of the CD
track;
❒"03.42": indicates the time elapsed since the
start of the track (if the relevant Menu function
is activated).
TRACK SELECTION (forward/back)
Briefly press the
button to play the previous CD
track and the
button to play the next track.
The tracks are selected cyclically: the first track is
selected after the last track and vice versa.
If the track has been played for more than 3
seconds, pressing the
button will cause the track
to be started again from the beginning.
In this case, if you want to play the previous track,
press the button twice consecutively.
297
SOUND-SYSTEM