2015 Lancia Delta wheel

252MAINTENANCE AND CARE
BODYWORK
PROTECTION AGAINST ATMOSPHERIC AGENTS
The main causes of corrosion are the following:
❍atmospheric pollution;
❍ salty air and humidity (coastal areas, or hot humid cli-
mates);
❍ seasonal environmental conditions.
The abrasive action of wind-borne atmospheric dust and
sand, as well as mud and gravel raised by other cars is
also not to be underestimated.
On your car, Lancia has implemented the best manufac-
turing technologies to effectively protect the bodywork
against corrosion. These include:
❍
paint products and systems which give the car a spe-
cial resistance to corrosion and abrasion;
❍ use of galvanised (or pre-treated) steel sheets with high
resistance to corrosion;
❍ spraying the underbody, engine compartment, wheel
arch internal parts and other elements with highly pro-
tective wax-based products;
❍ spraying protective plastic materials in the most ex-
posed areas: underdoor, inner wing parts, edges, etc.;
❍ using “open” boxed sections to prevent condensation
and pockets of moisture from causing rust inside.
BODY AND UNDERBODY WARRANTY
Your car is covered by warranty against perforation due
to rust of any original element of the structure or body-
work.
For the general terms of this warranty, refer to the War-
ranty Booklet.
233-256 Delta GB 1ed 03/04/14 13:28 Pagina 252

6
TECHNICAL SPECIFICATIONS257
Identification data ........................................................... 258
Engine codes - bodywork versions .................................... 260
Engine ........................................................................\
.... 261
Fuel supply syst em .......................................................... 262
Transmission ................................................................... 262
Brakes ........................................................................\
..... 263
Suspension ...................................................................... 263
Steering .......................................................................\
... 263
Wheels ........................................................................\
.... 264
Dimensions ..................................................................... 269
Performance ................................................................... 270
Weights .......................................................................\
.... 271
Capacities .......................................................................\
272
Fluids and lubr icants ...................................................... 273
Fuel consumpt ion ........................................................... 275
CO
2emissions ................................................................. 276
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 257

TECHNICAL SPECIFICATIONS263
6
Self-ventilated discsDisc
Controlled by hand lever, acting on rear brakes
BRAKES
IMPORTANT Water, ice and road salt spread on roads may deposit on the brake discs thus reducing braking efficien-
cy when braking for the first time.
Service brakes:
– front
– rear
Parking brake
Rack and pinion with electric power steering
10.6 / 11.2 (*)
SUSPENSIONS
McPherson independent wheels
Interconnected wheels with torsion beamFront suspensions
Rear suspensions
STEERING
(*) With 18” tyres
Type
Turning circle
(kerb to kerb) m
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 263

264TECHNICAL SPECIFICATIONS
WHEELS
RIMS AND TYRES
Pressed steel or alloy rims. Tubeless radial carcass tyres.
All approved tyres are listed in the Vehicle Registration
Document.
IMPORTANT In the event of discrepancies between the
information provided in this “Owner’s handbook” and the
“Registration Document”, consider the specifications
shown in the log book only. For safe driving, the car must
be fitted with tyres of the same make and type on all
wheels.
IMPORTANT Do not use air chambers with Tubeless tyres.
SPACE-SAVER WHEEL
Pressed steel rim. Tubeless tyre.
WHEEL GEOMETRY
Total front toe in: –1
±1 mm
Total rear toe in: 2
± 2 mm
The figures refer to the car in running order. UNDERSTANDING TYRE MARKING fig. 5
Example: 195/55 R 16 91 V
195 = Nominal width (S, distance in mm between
sidewalls).
55 = Height/width ratio (H/S) as a percentage.
R = Radial tyre.
16 = Rim diameter in inches (Ø).
91 = Load index (capacity).
V = Maximum speed index.
fig. 5L0E0120m
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 264

266TECHNICAL SPECIFICATIONS
UNDERSTANDING RIM MARKING fig. 5
Example: 7J x 16 H2 ET 31
7 = rim width in inches (1).
J = rim drop centre outline (side projection where thetyre bead rests) (2).
16 = rim nominal diameter in inches (corresponds to the diameter of the tyre to be mounted) (3 = Ø).
H2 = shape and number of humps (circumference pro- jection which holds tubeless tyre beads on the rim).
ET 31 = wheel camber angle (distance between the disc/rim supporting plane and the wheel rim cen-
tre line).
fig. 6L0E0193m
RIM PROTECTOR TYRES fig. 6
Do NOT fit wheel caps when using integral
wheel caps fixed (with springs) to the steel
rim and after-sale tyres provided with Rim
Protector (fig. 5a). The use of unsuitable tyres and
wheel caps may cause sudden loss of tyre pressure.
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 266

TECHNICAL SPECIFICATIONS267
6
7Jx16”- ET31
7Jx16”- ET31
7Jx17”- ET31
7,5Jx18”- ET35 (**)
4Bx15” H-ET 35 (*) 125/90 R15-96M (*)
(■) 1.6 Multijet 120 HP versions
(*) Depending on the trim level, the space-saver wheel for the 1.6 Multijet \
120 HP version has a 205/55 R16-91V tyre and a 7Jx16” - ET31 rim. In this case the 205/55 R16 91V tyre has the same specifications as the space-saver wheel: the informa-
tion in “Replacing a wheel” paragraph therefore refers to the 205/55 R16 91V tyre.
(**) For versions/markets, where provided
(
❏) Tyre not suitable for fitting snow chains.
Rims TyresTyres Space-saver wheel
for snow (for versions/markets, where provided)
Rim Tyre
On 205/55 R16-91V tyres, use reduced size snow chains with a maximum pro\
jection of 9 mm beyond
the tyre profile. On 225/45 R17-91W tyres, use reduced size snow chains \
with a maximum projection
of 7 mm beyond the tyre profile.
IMPORTANT Special techniques need to be adopted for 225/40 R18 92W tyres. For this reason, these tyres can only
be requested when the vehicle is purchased. Do not fit this tyre after vehicle has been purchased !
195/155R16-91V (■ )
205/55 R16-91V
225/45 R17-91W
225/40 R18-92W
(❏) (**)
REINFORCED
195/55R16-91T (■ ) (M+S)
205/55 R16-91T (M+S)
225/45 R17-91T (M+S)
225/40 R18-92T (M+S)
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 267

2.72.5
2.7 2.5
2.7 2.5
2.9 2.7195/55 R16-91V
205/55 R16-91V
225/45 R17-91W
225/40 R18-92W
268TECHNICAL SPECIFICATIONS
205/55 R16-91V 125/90 R15-96
2.4 2.2
2.4 2.2
2.4 2.2
2.6 2.4
Add +0.3 bar to the prescribed pressure when the tyres are warm. Check correct pressure when the tyres are cold.
With snow tyres, add +0.2 bar to the prescribed pressure for standard tyres.
When travelling at speeds over 160 km/h, inflate the tyres to the values specified for fully laden conditions.
The TPMS is not fitted with 195/55 R16 91V tyres.
COLD TYRE INFLATION PRESSURES (bar)
2.2
4.2
Size Inflation pressure
SPACE-SAVER/SPARE WHEEL
TYRES PROVIDED
Size Medium load Full load
Front Rear FrontRear
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 268

Gearboxes and
differentials
CV joints
differential side
CV joints
wheel side
Hydraulic brakes and
hydraulic clutch controls
windscreen/rear window
washer/wiper
Cooling circuits
Percentage of use:
50% water
50% PARAFLU
UP(❑)
To be mixed with diesel
(25 cc per 10 litres)
To be used undiluted or
diluted in windscreen/rear
window washer/wiper
systems
TUTELA TRANSMISSIONGEARFORCE
Contractual Technical
Reference No. F002.F10
TUTELA STAR 700
Contractual Technical
Reference No. F701.C07
TUTELA ALL STAR
Contractual Technical
Reference No. F702.G07
TUTELA TOP 4
Contractual Technical
Reference No. F001.A93
PARAFLU
UP(●)
Contractual Technical
Reference No. F101.M01
TUTELA DIESEL ARTContractual Technical
Reference No. F601.L06
TUTELA
PROFESSIONAL SC 35
Contractual Technical
Reference No. F201.D02
SAE 75W grade synthetic base lubricant.
FIAT 9.55550-MZ6 classification
Grease for constant velocity joints with low friction
coefficient. NL.GI. 0-1 consistency.
FIAT 9.55580 classification
Molybdenum disulphide grease, for use at
high operating temperatures. NL.GI. 1-2 consistency
FIAT 9.55580 classification
Synthetic fluid for brake and clutch systems.
It exceeds the specifications: FMVSS no. 116 DOT 4,
ISO 4925, SAE J 1704. FIAT 9.55597 classification
Red protective agent with antifreeze action, based on
inhibited monoethylene glycol with organic formula.
Exceeds CUNA NC 956-16, ASTM D 3306 specifications.
Additive for diesel fuel, protecting Diesel engines.
Mixture of spirits and surfactants.
Exceeds CUNA NC 956-11 specifications. FIAT 9.55522 classification
274TECHNICAL SPECIFICATIONS
Brake fluid
Protective
agent
for radiators
Diesel
fuel additive
Windscreen
and rear
window
washer fluid
(●) IMPORTANT Do not top up or mix using fluids with different specifications.
(
❑) When the vehicle is used in particularly harsh climate conditions, we recommend using a mixture of 60% PARAFLUUPand
40% demineralised water.
Lubricants
and greases
for drive
transmission
Usage Fluid and lubricant specifications Fluids and lubricants Applicationsfor a correct use of the car genuine
257-280 Delta GB 1ed 02/09/13 09.37 Pagina 274