2015 JEEP GRAND CHEROKEE turn signal bulb

Turn Signals
Move the multifunction lever up or down and the arrows
on each side of the instrument cluster flash to show
proper operation of the front and rear turn signal lights.
NOTE:If either light remains on and does not flash, or
there is a very fast flash rate, check for a defective outside
light bulb. If an indicator fails to light when the lever is
moved, it would suggest that the indicator bulb is
defective.
Lane Change Assist
Tap the lever up or down once, without moving beyond
the detent, and the turn signal (right or left) will flash
three times then automatically turn off.
Flash-To-Pass
You can signal another vehicle with your headlights by
partially pulling the multifunction lever toward the steer-
ing wheel. This will cause the high beam headlights to
turn on until the lever is released.
High/Low Beam Switch
Push the multifunction lever toward the instrument
panel to switch the headlights to high beam. Pulling the
multifunction back toward the steering wheel will turn
the low beams back on, or shut the high beams off.
3
UNDERSTANDING THE FEATURES OF YOUR VEHICLE 177

5. Front Fog Light Indicator — If Equipped
This indicator will illuminate when the front fog
lights are on.
6. Upper Left Selectable DID
This area of the cluster will display selectable informa-
tion such as compass, outside temperature, etc. For
further information, refer to “Driver Information Display
(DID)” in this section.
7. Turn Signal Indicator
The arrows will flash with the exterior turn
signals when the turn signal lever is operated.
A tone will chime, and a DID message will
appear if either turn signal is left on for more
than 1 mile (1.6 km).
NOTE:If either indicator flashes at a rapid rate, check
for a defective outside light bulb.
8. Speedometer
Indicates vehicle speed.
9. Upper Right Selectable DID
This area of the cluster will display selectable informa-
tion such as compass, outside temperature, etc. For
further information, refer to “Driver Information Display
(DID)” in this section.
10. Malfunction Indicator Light (MIL)
The Malfunction Indicator Light (MIL) is part of
an onboard diagnostic system called OBD II that
monitors engine and automatic transmission con-
trol systems. The light will illuminate when the key is in
the ON/RUN position before engine start. If the bulb
does not come on when turning the key from OFF to
ON/RUN, have the condition checked promptly.
Certain conditions, poor fuel quality, etc., may illuminate
the light after engine start. The vehicle should be serviced
4
UNDERSTANDING YOUR INSTRUMENT PANEL 293

▫Front/Rear Axle Fluid..................640
▫Transfer Case........................641
▫Automatic Transmission................642
▫Appearance Care And Protection From
Corrosion...........................644
!FUSES..............................650
▫Power Distribution Center...............651
!VEHICLE STORAGE....................659
!REPLACEMENT BULBS.................660
!BULB REPLACEMENT..................662
▫High Intensity Discharge Headlamps (HID) — If
Equipped...........................662
▫Halogen Headlamps — If Equipped........663
▫Front Turn Signal.....................663
▫Front Fog Lamps.....................664
▫Rear Tail, Stop, and Turn Signal Lamps......665
▫Rear Liftgate Mounted Tail Lamp..........666
▫Center High-Mounted Stop Lamp (CHMSL) . .668
▫Rear License Lamp....................668
!FLUID CAPACITIES....................669
!FLUIDS, LUBRICANTS AND GENUINE PARTS . .670
▫Engine.............................670
▫Chassis............................672
600 MAINTAINING YOUR VEHICLE

Bulb Number
Headlamps (High Beam) - If Equipped9005
Premium Park/Turn Signal LampLED - (Service at Authorized Dealer)
Premium Daytime Running Lamp (DRL)LED - (Service at Authorized Dealer)
Front Fog LampsH11
Front Side Marker - If EquippedW5W
Premium Front Side Marker - If EquippedLED - (Service at Authorized Dealer)
Front Park/Turn Lamp - If Equipped7444NA (WY27/8W)
Rear Body Side Turn Signal Lamps7440NA (WY21W)
Auxiliary Liftgate Tail LampsLED - (Service at Authorized Dealer)
Liftgate Backup Lamps921 (W16W)
Rear License LampsLED - (Service at Authorized Dealer)
Rear Body Side Stop Lamps3157KRD LCP
7
MAINTAINING YOUR VEHICLE 661

WARNING!
A transient high voltage occurs at the bulb sockets of
High Intensity Discharge (HID) headlamps when the
headlamp switch is turned ON. It may cause serious
electrical shock or electrocution if not serviced prop-
erly. See your authorized dealer for service.
NOTE:On vehicles equipped with High Intensity Dis-
charge (HID) headlamps, when the headlamps are
turned on, there is a blue hue to the lamps. This dimin-
ishes and becomes more white after approximately 10
seconds, as the system charges.
Halogen Headlamps — If Equipped
1. Open the hood.
2. Turn the low or high beam bulb one–quarter turn
counterclockwise to remove from housing.
3. Disconnect the electrical connector and replace the
bulb.
CAUTION!
Do not touch the new bulb with your fingers. Oil
contamination will severely shorten bulb life. If the
bulb comes in contact with any oily surface, clean the
bulb with rubbing alcohol.
Front Turn Signal
1. Open the hood.
2. Turn the turn signal bulb one–quarter turn counter-
clockwise to remove from housing.
3. Disconnect the electrical connector and replace the
bulb.
7
MAINTAINING YOUR VEHICLE 663

6. Firmly and evenly push the bulb straight into the lamp
housing until both tabs snap firmly into place and are
fully engaged.
7. Connect the wiring harness to the front fog lamp
connector.
Rear Tail, Stop, and Turn Signal Lamps
1. Raise the liftgate.
2. Remove the two push-pins from the tail lamp housing.
3. Grasp the tail lamp and pull firmly rearward to
disengage the lamp from the aperture panel.Tail Lamp Push Pins
7
MAINTAINING YOUR VEHICLE 665

4. Twist socket counter clockwise and remove from
lamp.
5. Pull the bulb to remove it from the socket.
6. Replace the bulb, reinstall the socket, and reattach the
lamp assembly.
Rear Liftgate Mounted Tail Lamp
1. Raise the liftgate.
2. Use a fiber stick or flat blade screw driver to pry the
lower trim from the liftgate.
3. Continue removing the trim.
4. Disconnect the two trim panel lights.
1—RearStopLampBulbSocket2—LEDTailConnector–DoNotRemove3—RearTurnSignalBulbSocket
666 MAINTAINING YOUR VEHICLE