2015 INFINITI Q40 buttons

5
INFINITI Intelligent Key System
The INFINITI Intelligent Key system allows you to lock or
unlock the vehicle, open the trunk and start the engine.


It is important to make sure the Intelligent Key is
with you (that is, in your pocket or purse).



The operating range of the Intelligent Key is within
31.5 in (80 cm) from each request switch.



To lock the vehicle, push either door handle request switch 1 once
or press the
button
2 on the key fob.



To unlock the vehicle, perform one of the following procedures:



•

Push either door handle request switch 1 once; the corresponding
door will unlock. Push the door handle request switch 1 again
within 1 minute; all other doors will unlock, or
•


Press the button
3 on the key fob to unlock the driver’s side
door. Press the
button again; all other doors will unlock.
To release the trunk lid, press the button
4 for more than
1 second. Lift the trunk lid to access the trunk.
The Intelligent Key can also be used to activate the panic alarm by
pressing and holding the
button
5 for more than 1 second. Once
activated, the panic alarm and headlights will stay on for 25 seconds.
INFINITI INTELLIGENT KEY BATTERY DISCHARGE
If the battery in the Intelligent Key is almost discharged,
the guide lights
6 of the Intelligent Key port blink and
the Intelligent Key battery discharge indicator 7 is
displayed in the vehicle information display.
To start the engine under these circumstances, insert
the Intelligent Key into the key port with the buttons
facing upward and the key ring end toward you until
it latches into place. Then push the ignition switch to
start the engine.
To remove the Intelligent Key from the port, push the ignition switch to\

turn the engine off and then pull the Intelligent Key out of the port.
The Intelligent Key port does not charge the Intelligent Key battery.
If you see the low battery indicator
7, replace the battery in the
Intelligent Key.
Do not insert the mechanical key or any other objects into the intellige\
nt key port. Inserting any
object other than the Intelligent Key will damage the Intelligent Key po\
rt.
For more information, refer to the “Pre-driving checks and adjustments (section 3)”, the “Starting and driving (section 5)” and the
“ Maintenance and do-it-yourself (section 8)” of your Owner’s Manual.
first drive features
2
3
4
5
6
7
1
1811809_15b_Infiniti_Q40_QRG_091014.indd 59/10/14 3:42 PM

9
Climate Controls
1 AUTO BUTTON/DRIVER’S SIDE TEMPERATURE CONTROL DIAL
The auto mode may be used year-round. Press the AUTO button to turn the system on,
and the system will automatically control the inside temperature (autom\
atic cooling and/
or dehumidified heating), air flow distribution and fan speed.
Turn the driver’s side temperature control dial to the left for coole\
r air or rig ht for
warmer air.
2 DUAL BUTTON/PASSENGER’S SIDE TEMPERATURE CONTROL DIAL
Press the DUAL button to turn the passenger’s side temperature controls on or off. T\
his
will allow the passenger’s side temperature to be adjusted independen\
tly from the
driver’s side by turning the passenger’s side temperature control \
dial.
Turn the passenger’s side temperature control dial left for cooler ai\
r or right for
warmer air.
3 FAN SPEED CONTROL BUTTONS
To manually adjust the fan speed, press the button to increase the fan speed or
press the
button to decrease the fan speed.
Windshield Wiper and Washer Switch
Move the lever to one of the following positions to
operate the windshield wipers:
1 Mist (MIST) - One sweep operation of
the wipers.
2 Intermittent (INT) - Operate the wipers
intermittently. To increase or decrease the
wiper speed, twist the time control ring
3.
4 Low (LO) - Wipers operate at a continuous low-speed.
5 High (HI) - Wipers operate at a continuous high-speed.
6 Pull the lever toward you to activate the washer.
The wipers will operate several times.
For more information, refer to the “Instruments and controls (section 2)” of your
Owner’s Manual.
12
45
67
8
9
3
2
4
5
1MIST
OFF
INT
LO
HI
6
3
1811809_15b_Infiniti_Q40_QRG_091014.indd 99/10/14 3:42 PM

11
FM/AM/SiriusXM®* Satellite Radio with CD/DVD (if so equipped) Player
1 ON•OFF BUTTON/VOL (volume) CONTROL KNOB
Press the ON•OFF button to turn the system on or off.
Turn the VOL (volume) knob right or left to increase or decrease the volume.
2 SEEK•CAT AND TRACK BUTTONS
To scan quickly through each broadcasting station, press the SEEK•CAT button or the
TRACK button to stop at the next or previous broadcast station.
For satellite radio, press the SEEK•CAT button or the TRACK button to switch to the first
channel of the next or previous category.
Press the SEEK•CAT button or the TRACK button to change tracks on a CD or device.
Press and hold the SEEK•CAT button or the TRACK button to fast forward or rewind a
track on a CD.
3 AUDIO BUTTON/TUNE/FOLDER CONTROL KNOB
To manually tune the radio, turn the TUNE/FOLDER control knob left or right.
Press the AUDIO button to access the audio settings screen.
4 STATION PRESET BUTTONS
Twelve stations can be set for the FM band, 6 for the AM band and 18 for\
satellite radio.
To store a station in a preset, you must first select the radio band by \
pressing the
AM•FM/SAT button
5 and tune to the desired AM, FM or satellite radio station. Then press and hold the desired station select button (
1-6) until the preset number is
updated on the display and the sound is briefly muted. The channel indic\
ator will then
display, and the sound will resume. Programing is now complete.
To retrieve a previously set station, select the radio band where the pr\
eset was stored then
press the corresponding station select button (1-6).
*SiriusXM® Satellite Radio is only available on vehicles equipped with an optional\
satellite radio subscription service.
For more information, refer to the “Monitor, climate, audio, phone and voice recognition systems (section 4\
)” of your Owner’s Manual.
13
5
2
4
1811809_15b_Infiniti_Q40_QRG_091014.indd 119/10/14 3:42 PM

19
DVD Player (if so equipped)
With this DVD Player, you can play video files via a
DVD or CD from the front display.
To view movies on the front display, stop the
vehicle in a safe location, move the shift lever to
the P (PARK) position and apply the parking brake.
To reduce driver distraction, movies will not be
shown on the front display while the vehicle is in
any drive position.
For more information, refer to the “Monitor, climate, audio, phone and voice
recognition systems (section 4)” of your Owner’s Manual.
HomeLink® Universal Transceiver
The HomeLink® Universal
Transceiver can learn and
consolidate the functions of
up to three different hand-held
transmitters, operating items
such as garage doors, property
gates, outdoor and indoor
lights or alarm systems.
To program the HomeLink® Universal Transceiver:



•


Position the handheld transceiver 1-3 in (26-76 mm) away from the Home\
Link surface,
keeping the HomeLink indicator light in view.



•


Press and hold the desired HomeLink button and the handheld transmitter button
simultaneously until the HomeLink indicator light flashes slowly and the\
n rapidly.



•


Both buttons may be released when the indicator light flashes rapidly.
To verify the programing is complete, press and hold the HomeLink button\
and observe the
indicator light:



•

A solid, continuous light indicates the programing is complete and the H\
omeLink button
will activate your device.



•

A blinking light that turns to a solid, continuous light after 2 seconds\
indicates additional
steps are required to complete the programing.
An additional person may make the remaining steps easier. To complete th\
e
programing process:



•

At the receiver of the device that you are programing to the HomeLink bu\
tton, press
and release the “learn” or “smart” button (the name may var\
y by manufacturer but it is
usually located near where the hanging antenna wire is attached to the u\
nit). You have
approximately 30 seconds to initiate the following step.



•

Press and hold the programed HomeLink button for 2 seconds and release.
You may have to repeat the previous 2 steps up to 3 times to complete th\
e programing
process. HomeLink should now activate your device.
For more information, refer to the “Instruments and controls (section 2)” of your Owner’s Manual, the HomeLink website at
www.homelink.com or call 1-800-355-3515.
HOMELINK
1811809_15b_Infiniti_Q40_QRG_091014.indd 199/10/14 3:43 PM