2015 HYUNDAI I20 manual radio set

##!'%$&%" '&$
(( Continued)
• In case of product malfunction, please contact your place of pur-
chase or After Service ce nter.
• Placing the audio system within an electromagnetic environment may
result in noise interference.
• Prevent caustic solutions such as perfume and cosmetic oil from
contacting the dashboard because
they ma y cause damage or discol-
oration.
RadioRadio ModeChange Mode:
[RADIO
]button
• You can toggle between the radio modes using
[RADIO]
button.
• If
[SETUP/CLOCK]
 [Display] 
[Mode Popup] is turned [Off], then
each time you press the
[RADIO]
button, you can toggle between
radio modes (FM1 ➟ FM2 ➟AM ➟
DRM ➟FM1).
• The radio mode popup will not be displayed when
[SETUP/CLOCK]
button [Display] [Mode popup]
is turned [Off].
Search Frequency:
[SEEK/TRACK]
button• Searches the previous/next broad- cast frequencies.
- Short press of button: searchesthe previous/next available
broadcast frequency.
- Long press of button: Frequency is controlled by 1 step quickly.
When the button is released after
pressing and holding, searches
the previous/next available
broadcast frequency.Change Frequency:
TUNE
knob
Changes frequency by turning the
knob left/right. You can seek avail-
able frequencies manually.Saved Frequency:
[1] ~ [6]
(Preset)
buttons
• Pressing the button: Plays the fre-
quency saved in the corresponding
button.
• Pressing and holding the button (more than 1.0 second): Saves the
currently playing broadcast to the
selected button and sound a BEEP.

#!'%$&%" '&$
IInformation
• Up to 2000 phone numbers can be
downloaded from a single, paired
Bluetooth
®
device.
• If the caller’s number is listed in Contacts, the caller’s name will be
displayed. Otherwise, only the num-
ber will be displayed. In some
Bluetooth
®
devices, the phone num-
ber may not be displayed.
• In some Bluetooth
®
devices, the Use
Private feature may not be supported.
• In some Bluetooth®
devices, the
Switch feature may not be supported.
• The phone number may not be properly displayed in some
Bluetooth
®
devices.
• During a phone call on a Bluetooth
®
Handsfree, you cannot access other
modes, such as Radio and Setup.
• Depending on handset types, the in- call volume the other party hears
may differ. If the other party hears
your voice too low or too loud,
adjust the mic volume.
Phone settingsPress the
[PHONE]
button Select
[Phone settings].
• Moves to a screen of Phone Settings. Refer to Setup ➟ Phone
manual for more information.
SetupDisplayPress the
[SETUP/CLOCK]
button 
Select [Display].
• Media Display: When playing an MP3 file, select the desired display
info from [Folder/File] or
[Artist/Title/Album].
• Mode Popup: During [On] state, press the
[RADIO]
or
[MEDIA]
but-
ton to display the mode change
popup.
• Text Scroll: If MP3 file name is too long to display, the file name is
scrolled from right to left.
i

TTo prevent damage to your vehicle:
• Only use a 12-volt power supply (battery or jumper system) to jump
s tart your vehicle.
• Do not attempt to jump start your vehicle by push-starting.
Information
An inappropriately disposedbattery can be harmful to the
environment and human
health. Dispose the battery
according to your local law(s)
or regulation.
Jump starting procedure 1.Position the vehicles close enough that the jumper cables will reach,
but do not allow the vehicles to
touch.
2.Avoid fans or any moving parts in the engine compartment at all
times, even when the vehicles are
turned off.
3.Turn off all electrical devices such as radios, lights, air conditioning,
etc. Put the vehicles in P (Park, for
Continuously Variable Transaxle
vehicle) or neutral (for Manual
Transaxle vehicle), and set the
parking brakes. Turn both vehicles
OFF.
iNOTICE
!$#'#"'"' %'$%'&&&%
Pb
•
Improper jump starting proce-
dure can result in battery explo-
sion and acid burn hazard.
•
Loosely connected battery
cables could damage the elec-
tronic control units.
•
To disconnect battery terminals
wait for at least 2 minutes to
allow discharge of high voltage
or it cou ld lead to personal
injury.
•
While disconnecting, always dis-
connect the -VE terminal first
and while connecting, always
connect the -VE terminal last.
CAUTION