2015 HYUNDAI I20 fuel
[x] Cancel search: fuelPage 375 of 400
1 . $ (
, 2 0 4 / 3 4 2 4 - 3
PCB Block (Diesel engine)FFuse Name
Symbol
Fuse rating
Circuit Protected
ECU 4
20A
ECM
ECU 2
15A
E/R Junction Block (RLY. 1), Electrical EGR Control Valve, Mass Air Flow Sensor,
WGT Control Solenoid Valve, Camshaft Position Sensor, Immobilizer Module
ECU 5
10A
Fuel Pressure Regulator Valve
Page 385 of 400
1 . ' $
, 2 0 4 / 3 4 2 4 - 3
BBright-metal maintenance• To remove road tar and insects,use a tar remover, not a scraper or
other sharp object.
• To protect the surfaces of bright- metal parts from corrosion, apply a
coating of wax or chrome preser-
vative and rub to a high luster.
• During winter weather or in coastal areas, cover the bright metal parts
with a heavier coating of wax or
preservative. If necessary, coat the
parts with non-corrosive petroleum
jelly or other protective compound.
Underbody maintenanceCorrosive materials used for ice and
snow removal and dust control may
collect on the underbody. If these
materials are not removed, acceler-
ated rusting can occur on the under-
body parts such as the fuel lines,
frame, floor pan and exhaust system,
even though they have been treated
with rust protection.
Thoroughly flush the vehicle under-
body and wheel openings with luke-
warm or cold water once a month,
after off-road driving and at the end
of each winter. Pay special attention
to these areas because it is difficult
to see all the mud and dirt. It will do
more harm than good to wet down
the road grime without removing it.
The lower edges of the doors, rocker
panels, and frame members have
drain holes that should not clog with
dirt; trapped water in these areas can
cause rusting.
After washing the vehicle, test the
brakes while driving slowly to see
if they have been affected by
wat er. If braking performance is
impaired, dry the brakes by apply-
ing them lightly while maintaining
a sl ow forward speed.
WARNING
Page 391 of 400
1 . 1 +
, 2 0 4 / 3 4 2 4 - 3
$ $ ! ! " # " # $ The emission control system of your
vehicle is covered by a written limited
warranty. Please see the warranty
information contained in the Service
Passport in your vehicle.
Your vehicle is equipped with an
emission control system to meet all
emission regulations.
There are three emission control
systems which are as follows.
(1) Crankcase emission control sys-
tem
(2) Evaporative emission control sys- tem
(3) Exhaust emission control system
In order to assure the proper function
of the emission control systems, it is
recommended that you have your
car inspected and maintained by an
authorized HYUNDAI dealer in
accordance with the maintenance
schedule in this manual.
1. Crankcase emission control systemThe positive crankcase ventilation
system is employed to prevent air
pollution caused by blow-by gases
being emitted from the crankcase.
This system supplies fresh filtered air
to the crankcase through the air
intake hose. Inside the crankcase,
the fresh air mixes with blow-by
gases, which then pass through the
PCV valve into the induction system.
2. Evaporative emission controlsystemThe Evaporative Emission Control
System is designed to prevent fuel
vapors from escaping into the atmos-
phere.CanisterFuel vapors generated inside the fuel
tank are absorbed and stored in the
onboard canister. When the engine is
running, the fuel vapors absorbed in
the canister are drawn into the surge
tank through the purge control sole-
noid valve.Purge Control Solenoid Valve(PCSV)The purge control solenoid valve is
controlled by the Engine Control
Module (ECM); when the engine
coolant temperature is low during
idling, the PCSV closes so that evap-
orated fuel is not taken into the
engine. After the engine warms up
during ordinary driving, the PCSV
opens to introduce evaporated fuel to
the engine.
Page 393 of 400
1 . 1 (
, 2 0 4 / 3 4 2 4 - 3
OOperating precautions for catalytic
converters (if equipped)
Your vehicle is equipped with a cat-
alytic converter emission control
device.
Therefore, the following precautions
must be observed:
• Use only UNLEADED FUEL for
Petrol engine.
• Do not operate the vehicle when there are signs of engine malfunc-
tion, such as misfire or a noticeable
loss of performance.
• Do not misuse or abuse the engine. Examples of misuse are
coasting with the ignition off and
descending steep grades in gear
with the ignition off.
• Do not operate the engine at high idle speed for extended periods (5
minutes or more).
• Do not modify or tamper with any part of the engine or emission con-
trol system. All inspections and
adjustments must be made by an
authorized HYUNDAI dealer. • Avoid driving with a extremely low
fuel level. Running out of fuel could
cause the engine to misfire, dam-
aging the catalytic converter.
Failure to observe these precautions
could result in damage to the catalyt-
ic converter and to your vehicle.
Additionally, such actions could void
your warranties.
Fire•
A hot exhaust system can ignite
flammable items under your
vehicle. Do not park, idle, or
drive the veh icle over or near
flammable objects, such as
grass, vegetation, paper,
leaves, etc.
•
The exhaust system and catalyt-
ic system are very hot while the
engine is running or immediate-
ly afte r the engine is turned off.
Keep away from the exhaust
system and catalytic, you may
get burned. Also, do not remove
the heat sink around the
exhaust system, do not seal the
bottom of the vehicle or do not
coa t the vehicle for corrosion
control. It may present a fire risk
under certain conditions.
WARNING
Page 398 of 400
!
1 0
+ ' - " - ' ( $ - ) , % * * ) , % # + & * - , " ) & # ( $ - ) ,
% ) " ) ' ! ) ! # % ( & ' $ & ' ! & & ( $ ( )
To help achieve proper engine and powertrain performance and durability, use only lubricants of the proper quality.
The correct lubricants also help promote engine efficiency that results in improved fuel economy.
These lubricants and fluids are recommended for use in your vehicle.
LubricantVolumeClassification
Engine oil *
\f*2 *5
(drain and refill) Petrol engine \f.2 L
3.6
l
ACEA A5/B5*
3
Petrol engine \f.4 L 3.5
l
ACEA A5/B5*3
Diesel engine5.3 lACEA B4*4
Manual transaxle fluid Petrol engine \f.2 L
\f.5 ~ \f.6
l
API Service GL\b4, SAE 70W
(HYUNDAI genuine transaxle fluid)
Diesel engine \f.7 ~ \f.8
l
Continuously variable
transaxle fluid Petrol engine \f.2 L
6.0
l
SP\bCVT\f
Automatic transaxle fluid Petrol engine \f.4 L 6.8
l
DIAMOND ATF SP\bIII, SK ATF SP\bIII
Coolant Petrol engine
4.3
l MIXTURE, Antifreeze with water
(Ethylene glycol base coolant for aluminum radiator)
Diesel engine
6.4
l
Brake/Clutch fluid 0.7~0.8
l
FMVSS\f\f6 DOT\b3 or DOT\b4
Fuel 40
l
\b
*\f : Refer to the recommended SAE viscosity numbers on the next page.
*2: Engine oils labeled Energy Conserving Oil are now available. Along with other additional benefits, they contribute to fuel economy by reducing
the amount of fuel necessary to overcome engine friction. Often, these improvements are difficult to measure in everyday driving, but in a year’s
time, they can offer significant cost and energy savings.
*3 : If the recommended engine oil is not available in your country, you are able to use API SL/ / ILSAC GF\b3 or ACEA A3.
*4 : If the recommended engine oil is not available in your country, you are able to use engine oil above API CH\b4.
*5: We recommend that you use the engine oils approved by HYUNDAI Motor India Ltd. We recommend that you consult an authorized HYUNDAI
dealer for details
.
Page 399 of 400
!
+ ' - " - ' ( $ - ) , % * * ) , % # + & * - , " ) & # ( $ - ) ,
Recommended SAE viscosity
numberEngine oil viscosity (thickness) has
an effect on fuel economy and cold
weather operating (engine start and
engine oil flowability). Lower viscosi\b
ty engine oils can provide better fuel
economy and cold weather perform\b
ance, however, higher viscosity
engine oils are required for satisfac\b
tory lubrication in hot weather. Using oils of any viscosity other than
those recommended could result in
engine damage.
When choosing an oil, consider the
range of temperature your vehicle
will be operated in before the next oil
change. Proceed to select the rec\b
ommended oil viscosity from the
chart.
Always be sure to clean the area
around any filler plug, drain plug,
or dipstick before checking or
draining any lubricant. This is
especially important in dusty or
sandy areas and when the vehicle
is used on unpaved roads.
Cleaning the plug and dipstick
areas will prevent dirt and grit from
entering the engine and other
mechanisms that could be dam\b
aged.
CAUTION
Temperature Range for SAE Viscosity Numbers
Temperature
°C
(°F)\b 3 0 \b 2 0 \b \f 0 0 \f 0 2 0 3 0 4 0 5 0 \b \f 0 0 2 0 4 0 6 0 8 0 \f 0 0 \f 2 0
Diesel
Engine Oil
5W\b30
\f5W\b40
\f0W\b30
0W\b30
Petrol
Engine Oil *\f
20W\b50
\f0W\b30
\f5W\b40
OW\b30, 5W\b30, 5W\b40
*\f : For better fuel economy, it is recommended to use the engine oil of a viscosity grade SAE 5W\b30 (ACEA A5/B5). However, if the engine oil is not available in your coun\btry, select the proper engine oil using the engine oil viscosity chart.