2015 HYUNDAI I20 sensor

 
"&t%'s%st&'!"'%!'&&
Side air bags
Side air bags (side impact and\for
curtain air bags) are designed to
inflate when an impact is detected by
side collision sensors depending on
the crash severity, speed or angles of
impact resulting from a side impact
collision.
Although the front air bags (driver’s
and front passenger’s air bags) are
designed to inflate only in frontal col
lisions, they also may inflate in other
types of collisions if the front impact
sensors detect a sufficient impact.
Side air bags (side impact and\for
curtain air bags) are designed to
inflate only in side impact collisions,
but they may inflate in other colli
sions if the side impact sensors detect a sufficient impact.
If the vehicle chassis is impacted by
bumps or objects on unimproved
roads or sidewalks, air bags may
deploy. Drive carefully on unim
proved roads or on surfaces not
designed for vehicle traffic to prevent
unintended air bag deployment.
Air bag noninflation conditions
• In certain lowspeed collisions the air bags may not deploy. The air
bags are designed not to deploy in
such cases because they may not
provide benefits beyond the pro
tection of the seat belts in such col
lisions. • Front air bags are not designed to
inflate in rear collisions, because
occupants are moved backward by
the force of the impact. In this
case, inflated air bags would not be
able to provide any additional ben
efit.
OPA037041
OPA037042

 
"&t%'s%st&'!"'%!'&&

• Front air bags may not inflate inside impact collisions, becauseoccupants move to the direction of
the collision, and thus in sideimpacts, frontal air bag deployment
would not provide additional occu
pant protection.
However, side impact or curtain air
bags may inflate depending on the
intensity, vehicle speed and angles
of impact. • In a slant or angled collision, the
force of impact may direct the
occupants in a direction where the
air bags would not be able to pro
vide any additional benefit, and
thus the sensors may not deploy
any air bags. • Just before impact, drivers often
brake heavily. Such heavy braking
lowers the front portion of the vehi
cle causing it to “ride” under a vehi
cle with a higher ground clearance.
Air bags may not inflate in this
"underride" situation because
deceleration forces that are detect
ed by sensors may be significantly
reduced by such “underride” colli
sions.
OSA038121OBH038060OPA037043

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3AUTO light position (if equipped)When the light switch is in the AUTO
position, the parking (position) light
and headlights will be turned ON or
OFF automatically depending on the
amount of light outside the vehicle.
Even with the AUTO light feature in
operation, it is recommended to
manually turn ON the lights when
driving at night or in a fog, or when
you enter dark areas, such as tun-
nels and parking facilities. •
•
Do not cover or spill anything on
the sensor (1) located on the
instrument panel.
• Do not clean the sensor using a win- dow cleaner, the cleanser may
leave a light film which could inter-
fere with sensor operation.
• If your vehicle has window tint or other types of metallic coating on
the front windshield, the AUTO
light system may not work proper-
ly.
High beam operationTo turn on the high beam headlamp,
push the lever away from you. The
lever will return to its original position.
The high beam indicator will light
when the headlamp high beams are
switched on.
To turn off the high beam headlamp,
pull the lever towards you. The low
beams will turn on.
NOTICE
OLF044192R
OLF044085R
Do not use high beam when there
are other vehicles approaching you.
Using high beam could obstruct the
other driver's vision.
WARNING

)'
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
PParking Distance Warning
(Reverse) System (if equipped)The Parking Distance Warning
(Reverse) System assists the driver
during reverse movement of the vehi-
cle by chiming if any object is sensed
within the distance of about 120 cm
(47 in.) behind the vehicle. This is a supplemental system that
senses objects within the range and
location of the sensors, it cannot
detect objects in other areas where
sensors are not installed.
Operation of the Parking Distance
Warning (Reverse) SystemOperation condition • This system will activate when
backing up with the power on.
• Sensing distance when backing up is approximately 120 cm (47 in.)
when you are driving less than 10
km/h (6 mph).
• When more than two objects are sensed at the same time, the clos-
est one will be recognized first.
OIB047065
Sensors
OIB047189
Sensors
•
ALWAYS look around your vehi-
cle to make sure there are no
objects or obstacles before mov-
ing the vehicle in any direction to
prevent a collision.
•
Always pay close attention when
the vehicle is driven close to
objects, particularly pedestrians,
and especially children.
•
Be aware that some objects
may not be detected by the sen-
sors, due to the objects dis-
tance, size or material, all of
which can limit the effectiveness
of the sensor.
WARNING
■ 5 Door■Cross

)'#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3Types of warning indicator and
sound
••If an object is in between sensors
or close to a sensor, the displayed
indicator may differ from the above
illustration.
• Do not wash the vehicle's sensor with high pressure water.
• When you shift into the R (Reverse) position and one or
more of the below situation occurs,
this may indicate a malfunction
with the parking assist system.
• You don't hear an audible warning sound or the buzzer sounds inter-
mittently.
If this occurs, we recommend that
the system be checked by an
authorized HYUNDAI dealer.
Non-operational conditions of Parking Distance Warning(Reverse) SystemThe Parking Distance Warning
(Reverse) System may not operate
normally when:• Moisture is frozen to the sensor.
• The sensor is covered or stained
with foreign material, such as snow
or water, or the sensor cover is
blocked.There is a possibility of a parking
assist system malfunction when:• Driving on uneven road surfacessuch as unpaved roads, gravel,
bumps, or gradient.
• Objects generating excessive noise such as vehicle horns, loud motor-
cycle engines, or truck air brakes
can interfere with the sensor.
• Heavy rain or water spray is present.
• Wireless transmitters or mobile phones are present near the sensor.
• The sensor is covered with snow.
• Any non-factory equipment or accessories have been installed, or
if the vehicle bumper height or sen-
sor installation has been modified.
NOTICE
Distance from
object
Warning
indicator
Warning sound
120cm ~ 61cm
(47 in. ~ 24 in.)
Buzzer beeps
intermittently.
60cm ~ 31cm
(24 in. ~ 12 in.)
Buzzer beeps
more frequently.
Less than
30 cm (12 in.)
Buzzer beeps continuously.
• is displayed. (if equipped)

)')
#10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
DDetecting range may decrease
when:• Outside air temperature is extremely hot or cold.
• Undetectable objects smaller than about 1 m (40 in.) and narrower
than about 14 cm (6 in.) in diameter.The following objects may not be
recognized by the sensor:• Sharp or slim objects such asropes, chains or small poles.
• Objects, which tend to absorb sen- sor frequency such as clothes,spongy material or snow.
Information
The system may not recognize objects
less than 30 cm (12 in.) from the sen-
sor, or it may sense an incorrect dis-
tance.Do not push, scratch or strike the
sensor with any hard objects that
could damage the surface of the
sensor. Sensor damage could occur.iNOTICE
Your new vehicle warranty does
not cover any accidents or dam-
age to the vehicle or injuries to its
occupants due to a Parking
Distance Warning (Reverse)
System malfunction. Always drive
safely and cautiously.
WARNING

)' #10*30-30.2+3%.,/3(21+2"1,/2*3!-$&3
IInformation
Never place anything near the sensor
located to ensure better control of the
heating and cooling system.
Manual heating and air condition-
ingThe heating and cooling system can
be controlled manually by pressing
buttons other than the AUTO button.
In this case, the system works
sequentially according to the order of
buttons selected.
When pressing any button (or turning
any knob) except the AUTO button
while using automatic operation, the
functions not selected will be con-
trolled automatically.
1. Start the engine.
2. Set the mode to the desired posi- tion.
To improve the effectiveness of
heating and cooling:- Heating:
- Cooling: 3. Set the temperature control to the
desired position.
4. Set the air intake control to the outside (fresh) air position.
5. Set the fan speed control to the desired speed.
6. If air conditioning is desired, turn the air conditioning system on.
7. Press the AUTO button in order to convert to full automatic control of
the system.
i
OIB044080

1.+1
,204/3424-3
!#$ "$#Filter replacement You can clean the filter when inspect-
ing the air cleaner element.
Clean the filter by using compressed
air.
1. Loosen the air cleaner cover attaching clips and open the cover. 2. Remove the used filter and wipe
the inside of the air cleaner hous-
ing carefully not to remain dusts in
the cover housing.
3. Place new filter with clean hands and ensure the rubber gasket is
not taken off.
4. Lock the cover with attaching clips.
Replace the filter according to the
Maintenance Schedule.
If the vehicle is operated in extreme- ly dusty or sandy areas, replace theelement more often than the usualrecommended intervals. (Refer to“Maintenance under severe usageconditions” in this chapter.)
• Do not drive with the filter removed; this will result in exces-
sive engine wear.
• When replacing th e air cleaner fil-
ter, be careful that dust or dirt does
not enter the air intake, or damage
may result .
Keep the new filter clean of any
contamination while replacing.
• We recommend that you use parts for re placement from an author-
ized HYUNDAI dealer.NOTICE
OIB074017
OIB074018
Don’t clean the used filter. It can
cause contaminations on the
clean side of filter to result in
engine wear or sensors’ failure.
CAUTION