Selecting an option from the main menu with
a submenu:
❒briefly press the MODE button to display the first
submenu option;
❒ press buttons
or
(with single presses) to
scroll through all the submenu options;
❒ briefly press the MODE button to select the
displayed submenu option and to open the
relevant settings menu;
❒ press buttons
or
(with single presses) to
select the new setting for this submenu option;
❒ briefly press the MODE button to store the new
setting and at the same time go back to the
previously selected submenu option.
MENU ITEMSLighting (Interior light adjustment)
With the side lights on, this function is used to set
the brightness of the instrument panel, radio
controls and dual zone automatic climate control
system controls (for versions/markets where
provided) to 8 levels.
Proceed as follows to adjust the brightness:
❒briefly press the MODE button: the previously set
level flashes on the display;
❒ press button
or
to set the required brightness
level;
❒ briefly press the MODE button to return to the
menu screen or hold the button down to return
to the standard screen without storing.
Speed Beep (Speed limit)
This function is used to set the car speed limit (km/h
or mph); the driver is immediately alerted when
this limit is exceeded (see section “Warning lights
and messages”).
To set the desired speed limit, proceed as follows:
❒ press the MODE button briefly, the display shows
the dedicated message;
❒ press the
or
button to select speed limit
activation (On) or deactivation (Off );
❒ if the function has been activated (On), press the
or
buttons to select the desired speed limit
and then press MODE to confirm.
20GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND DRIVING
WARNING LIGHTS AND MESSAGES
IN AN EMERGENCY SERVICING ANDMAINTENANCE
TECHNICAL
SPECIFICATIONS
INDEX
SET TEMPERATURE ALIGNMENT (MONO function) Press the MONO button to align the temperature between the driver side and passenger side. Then turn the AUTO or MONO knob to increase/decrease the temperature between the twoareas by the same amount. Press MONO again to deactivate the function. CLIMATE CONTROL SYSTEM COMPRESSOR ACTIVATION/DEACTIVATION Press the
button to switch on the climate control
system compressor. Compressor engagement ❒
button LED
on;
❒
symbol appears on display.
Compressor deactivation❒
button LED
off;
❒
symbol on display disappears;
❒
internal air recirculation excluded;
❒
AQSfunctiondisabled
With the climate control system compressor switched off, air cannot be introduced into thepassenger compartment that has a lowertemperature than the outside air; in this case the
symbol in the display will flash.
The deactivation of the climate control systemcompressor is memorised even after the engine hasstopped. To reactivate the climate control systemcompressor, press the
or AUTO button again:
if you press AUTO, the other manual settings will becancelled. IMPORTANT In order to preserve the battery charge, the electronic climate control managementpermits a higher ventilation speed than minimumonly if the engine is running at a speed greater than750 rpm. When the speed drops below thisthreshold – possible when setting off, for example –the ventilation speed is automatically reduced tominimum. AIR DISTRIBUTION SELECTION Press one or more of these buttons
/
/
to
manually select one of the seven possible air distribution settings for the passenger compartment:
Air flow to the windscreen and front sidewindow diffusers to demist/defrost them.Air flow to the front and rear footwell diffusers.This air distribution allows the passengercompartment to be warmed up quickly.
Air flow distribution between front andrear diffusers, centre/side dashboarddiffusers, rear diffuser and windscreen andfront side window demisting/defrostingdiffusers.
Air flow distribution to centre/side dashboarddiffusers (passenger's body).
50GETTING TO
KNOW YOUR CAR
SAFETY
STARTING AND
DRIVING
WARNING LIGHTSAND MESSAGESIN AN EMERGENCYSERVICING ANDMAINTENANCETECHNICAL
SPECIFICATIONS
INDEX
(forversions/markets,whereprovided).
