2015 Citroen DS3 key battery

DS3_en_Chap02_ouvertures_ed01-2015
Following disconnection of the vehicle battery, replacement   of   the   remote   control   battery   or  
i

n   the   event   of   a   remote   control   malfunction,  
y

ou   can   no   longer   unlock,   lock   or   locate   your  
v

ehicle.
F
 
F
irst   of   all,   use   the   key   in   the   lock   to   unlock  
o

r   lock   your   vehicle.
F
 
T
hen,   reinitialise   the   remote   control.
If
  the   problem   persists,   contact   a   CITROËN  
d

ealer   as   soon   as   possible.
Remote control problem
Reinitialisation
F Switch  off   the   ignition.
F  T urn   the   key   to   position   2 (Ignition).
F
 
P
ress   the   closed   padlock   immediately   for   a  
f

ew   seconds.
F
 
S
witch   off   the   ignition   and   remove   the   key  
f

rom   the   ignition   switch.
The
  remote   control   is   fully   operational   again.
Changing the battery
Battery ref.: CR1620 / 3 volts.F  U nclip   the   casing   by   inserting   a   coin   at   the  
n

otch   and   rotating.
F
 
S
lide   the   flat   battery   out   of   its   location.
F

S
lide the new battery into its location
observing
  the   original   direction.
F
 
C
lip   the   casing   in   place,   then   the   chrome  
f

inisher.
F
 
R
einitialise   the   remote   control.
If the battery is flat, you are
informed
  by   lighting   of   this   warning  
l

amp   in   the   instrument   panel,   an   audible   signal  
a

nd   a   message   in   the   multifunction   screen.
F
 
U
nfold   the   key.
F
 
R
elease   the   chrome   finisher   by   pressing   on  
l

ug   A.
F
 
M
aintain   pressure   on   lug   A   and   remove   the  
c

hrome   finisher   by   sliding   it   off   at   45°.

DS3_en_Chap02_ouvertures_ed01-2015
Activation
F Press button A  for   more   than   two   seconds.
A   confirmation   message   appears   in   the  
m

ultifunction   screen,   accompanied   by   an  
a

udible
 s
ignal.
deactivation
F Press button A   again   for   more   than  
two   seconds.
A
  confirmation   message   appears   in   the  
m

ultifunction   screen,   accompanied   by   an  
a

udible
 s
ignal. To
  lock   or   unlock   the   doors   mechanically   in   the  
e

vent   of   a   central   locking   system   failure   or   flat  
b

attery.
Emergency control
Locking the driver's door
F Insert
  the   key   in   the   lock,   then   turn   it   to   the  r
ight.
Unlocking the driver's door
F Insert   the   key   in   the   lock,   then   turn   it   to  t
he left.
Locking the passenger's door
F Remove   the   black   cap,   on   the   edge   of   the  d
oor,   using   the   key.
F
 
I
nsert   the   key   in   the   cavity,   then   turn   it   fully.
F
 
R
emove   the   key   and   refit   the   cap.
Unlocking the passenger's
door
F Pull  the   interior   door   opening   control.
In the event of a fault with the central
locking
 
system,
 
you
 
must
 
disconnect
 
t

he
 
battery
 
to
 
lock
 
the
 
boot
 
and
 
s

o
 
ensure
 
the
 
complete
 
locking
 
of
 
t

he vehicle.

101
DS3_en_Chap04_conduite_ed01-2015
Anti-theft protection
Electronic engine immobiliser
The key contains an electronic chip which has a  special   code.   When   the   ignition   is   switched  
o

n,   this   code   must   be   recognised   in   order   for  
s

tarting   to   be   possible.
This
  electronic   engine   immobiliser   locks   the  
e

ngine   management   system   a   few   minutes  
a

fter   the   ignition   is   switched   off   and   prevents  
s

tarting   of   the   engine   by   anyone   who   does   not  
h

ave   the   key.In the event of a fault, you are
informed
  by   illumination   of   this  
w

arning   lamp,   an   audible   signal   and  
a

  message   in   the   screen.It
  has   3   positions:
-
 
P
osition   1:   Stop
-
 
P
osition   2:   Ignition on
-
 
P
osition   3:   Starting
Ignition switch
Ignition on
In this position the vehicle's electrical equipment   can   be   used   or   accessories  
c

harged.
When
  the   state   of   charge   of   the   battery  
d

rops   to   a   reserve   level,   the   system   goes   into  
e

nergy   economy   mode:   the   power   supply   is  
a

utomatically   cut   off   to   preserve   the   state   of  
c

harge   of   the   battery.
Keep
 
safely,
 
away
 
from
 
your
 
vehicle,
 
t

he
 
label
 
attached
 
to
 
the
 
keys
 
given
 
to
 
y

ou
 
on
 
acquisition
 
of
 
the
 
vehicle.
Starting-switching off the engine
In this case, your vehicle will not start; contact a   CITROËN   dealer   as   soon   as   possible.
Avoid
  attaching   heavy   objects   to   the  
k

ey,   which   would   weigh   down   on   its  
b

lade   in   the   ignition   switch   and   could  
c

ause   a   malfunction.
driving

DS3_en_Chap04_conduite_ed01-2015
Stop & StartThe Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...). The engine   restarts   automatically   -   START   mode   -   as   soon   as   you   want   to   move   off.   The   restart   takes   place   instantly,   quickly   and   silently.
Per fect
  for   urban   use,   the   Stop   &   Start   system   reduces   fuel   consumption   and   exhaust   emissions   as   well   as   the   noise   level   when   stationary.
Operation
going into engine STOP mode
For your comfort, during parking manoeuvres,   STOP   mode   is   not  
a

vailable for a few seconds after
coming
  out   of   reverse   gear.
STOP
  mode   does   not   affect   the  
f

unctionality of the vehicle, such as for
example,
  braking,   power   steering...
Never
  refuel   with   the   engine   in   STOP  
m

ode;   you   must   switch   off   the   ignition  
w

ith   the   key.
The "ECO" 
warning
 
lamp
 
comes
 o
n
 
in
 
the
 
instrument
 
panel
 
and
 
the
 
e

ngine
 
goes
 
into
 
standby:
-

w

ith a manual gearbox , at speeds below
12
 
mph
 
(20
 
km/h),
 
when
 
you
 
put
 
the
 
gear
 
l

ever into neutral, and you release the
clutch
 
pedal.
-

w

ith a 5 or 6-speed electronic gearbox ,
when
 
stationary
 
or
 
at
 
speeds
 
below
 
5
 
mph
 
(

8
 
km/h)
 
(depending
 
on
 
version),
 
when
 
y

ou
 
press
 
the
 
brake
 
pedal
 
or
 
put
 
the
 
gear
 
s

elector in position
n
.
A

 
time
 
counter
 
calculates
 
the
 
sum
 o

f
 
the
 
periods
 
in
 
STOP
 
mode
 
during
 a

 
journey.
 
It
 
rests
 
itself
 
to
 
zero
 
every
 t

ime
 
the
 
ignition
 
is
 
switched
 
on
 
with
 t

he
 
key. STOP
  mode   is   not   invoked   when:
-  t he   driver's   door   is   open,
-
 
t
he   driver's   seat   belt   is   not   fastened,
-
 
t
he   vehicle   has   not   exceeded   6   mph  
(

10 km/h)   since   the   last   engine   start   using  
t

he   key,
-
 
t
he   engine   is   needed   to   maintain   a  
c

omfortable   temperature   in   the   passenger  
c

ompartment,
-
 
d
emisting   is   active,
-
 
s
ome   special   conditions   (battery   charge,  
e

ngine   temperature,   braking   assistance,  
a

mbient   temperature...)   where   the   engine   is  
n

eeded   to   assure   control   of   a   system.
Special cases: STOP mode not
available
The "ECO" warning   lamp   flashes   for  a
  few   seconds   then   goes   off.
This operation is perfectly normal.

DS3_en_Chap04_conduite_ed01-2015
The system is reactivated automatically at   every   new   start   using   the   key.
Reactivation
This system requires a battery with a special specification   and   technology   (reference  
n

umbers   available   from   a   CITROËN   dealer   or   a  
q

ualified
 w
orkshop).
Fitting
  a   battery   not   listed   by   CITROËN  
i

ntroduces   the   risk   of   malfunction   of   the  
s

ystem.
In
 
the
 
event
 
of
 
a
 
fault
 
with
 
the
 
system,
 
the
 
"

ECO OFF"
 
switch
 
warning
 
lamp
 
flashes
 
then
 
c

omes
 
on
 
continuously.
Have
 
it
 
checked
 
by
 
a
 
CITROËN
 
dealer
 
or
 
a
 
q

ualified
 w

orkshop.
In
 
the
 
event
 
of
 
a
 
fault
 
in
 
STOP
 
mode,
 
the
 
v

ehicle
 
may
 
stall.
 
All
 
of
 
the
 
instrument
 
panel
 
w

arning
 
lamps
 
come
 
on.
 
It
 
is
 
then
 
necessary
 
t

o
 
switch
 
off
 
the
 
ignition
 
and
 
start
 
the
 
engine
 
a

gain
 
using
 
the
 
key.
Operating fault Maintenance
Before doing anything under the b
onnet, deactivate the Stop & Start
system
  to   avoid   any   risk   of   injury  
r

esulting   from   automatic   operation   of  
S

TART   mode.
The
  Stop   &   Start   system   makes   use  
o

f   advanced   technology.   All   work  
o

n   this   type   of   battery   must   be   done  
b

y   a   CITROËN   dealer   or   a   qualified  
w

orkshop.
Press the "ECO OFF"
 
switch
 
again.
The
 
system
 
is
 
active
 
again;
 
this
 
is
 
confirmed
 
b

y
 
the
 
switch
 
warning
 
lamp
 
going
 
off,
 
a

ccompanied
 
by
 
a
 
message
 
in
 
the
 
screen.

DS3_en_Chap12_index-recherche_ed01-2015
Exterior
Remote control key 60 - 63,   101-103
- l ocking/unlocking
-


battery
-
a

nti-theft protection
-
 s

tarting Lighting
  controls  
1
30 -134
Headlamp
 adj

ustment
 1
35
Changing
 bu

lbs
 2
08-211
-
 
f
ront   lamps
-
 fo

glamps
-
d

irection indicator repeaters
W iper c ontrols
13

6 -13 9
Changing
  a   wiper   blade  
2
27 Door
  mirrors  
7
9
Doors
66 - 68
-
 ope

ning/closing
-
 
c
entral   locking
-
 em

ergency
 c
ontrol
Electric windows

6
4- 65
Fuel
  tank  
1
84-185
Misfuel prevention
1

86Accessories
23

4-235
Hill start assist

1
19
Braking
  assistance  
1
50 -151
Trajectory
  control  
1
51-152
Tyre pressures

1
98 -199, 262
Under-inflation detection
1

46-149
Boot
6

9
Temporary
  puncture   repair   kit  
1
95 -199
Changing
  a   wheel  
2
00 -206
-
tools
-
 r

emoving/refiting
Snow chains

2
07
Changing
 bu

lbs
 2
12-214
-
 
r
ear   lamps
-
 
3
D   rear   lamps
-
3
rd  brake lamp
-
 n
umber   plate   lamps
Rear
 
parking   sensors  
1
24-125
Reversing   camera  
1
26
Towbar
23
0-231
Towing
 2
28-229

5Driving











Stop & Start
The Stop & Start system puts the engine temporarily into standby - STOP mode - during stops in the traffic (red lights, traffic jams, or other...).
The engine restarts automatically - START mode - as soon as you want to move off. The restart takes place instantly, quickly and silently.
Per fect for urban use, the Stop & Start system reduces fuel consumption and exhaust emissions as well as the noise level when stationary.


Operation


Going into engine STOP mode


For your comfort, during parking
manoeuvres, STOP mode is not
available for a few seconds after
coming out of reverse gear.
STOP mode does not affect the
functionality of the vehicle, such as for
example, braking, power steering...

Never refuel with the engine in STOP
mode; you must switch off the ignition
with the key. The "ECO"
warning lamp comes
on in the instrument panel and the
engine goes into standby:


- with a manual gearbox
, at speeds below
12 mph (20 km/h), when you put the gear
lever into neutral, and you release the
clutch pedal.

- with a 5 or 6-speed electronic gearbox
,
when stationary or at speeds below 5 mph
(8 km/h) (depending on version), when
you press the brake pedal or put the gear
selector in position N
.

- with an automatic gearbox
, vehicle
stationary, when you press the brake pedal
or you place the gear selector in position N
. A time counter calculates the sum
of the periods in STOP mode
during a journey. It rests itself
to zero every time the ignition is
switched on with the key. STOP mode is not invoked when:


- the driver's door is open,

- the driver's seat belt is not fastened,

- the vehicle has not exceeded 6 mph
(10 km/h) since the last engine start using
the key,

- the engine is needed to maintain a
comfortable temperature in the passenger
compartment,

- demisting is active,

- some special conditions (battery charge,
engine temperature, braking assistance,
ambient temperature...) where the engine is
needed to assure control of a system.


Special cases: STOP mode not
available
The "ECO"
warning lamp flashes for
a few seconds then goes off.

This operation is per fectly normal.

7Driving

The system is reactivated automatically
at every new start using the key.



Reactivation

This system requires a battery with a special
specification and technology (reference
numbers available from a CITROËN dealer or a
qualified workshop).
Fitting a battery not listed by CITROËN
introduces the risk of malfunction of the system.
In the event of a fault with the system, the
"ECO OFF"
switch warning lamp flashes then
comes on continuously.
Have it checked by a CITROËN dealer or a
qualified workshop.
In the event of a fault in STOP mode, the
vehicle may stall. All of the instrument panel
warning lamps come on. It is then necessary
to switch off the ignition and start the engine
again using the key.


Operating fault
Maintenance


Before doing anything under the
bonnet, deactivate the Stop & Start
system to avoid any risk of injury
resulting from automatic operation of
START mode.

The Stop & Start system makes use
of advanced technology. All work
on this type of battery must be done
by a CITROËN dealer or a qualified
workshop.
Press the "ECO OFF"
switch again.
The system is active again; this is confirmed
by the switch warning lamp going off,
accompanied by a message in the screen.